HydrogenX Hydro6000x Manuel utilisateur
Hydro6000x
Instruction Manual
Contents
Specifications
Machine Parts Diagram
Inner Packaging Details
Safety Warnings
Installation
Replacement of the Battery
Replacement of the Filter Cartridge
Troubleshooting
Others
Warranty Information
1
1
2
3
4
6
7
8
9
Contents
Specifications
1
Specifications
Item No: Hydro6000X
Size: 120*125*297mm (4¾*5*11¾ in)
Water flow: 3L/min (0.79 G/min)
Working water pressure: 0.07-0.35Mpa (10.15-50.76 PSI)
Working water temperature: 5 to 35°C (41 to 95°F)
Weight: 1.7KGS (3.75 LBS)
Installation type: Quick fitting
Filters: UF Membrane &Composite Filter
Life of the filters: 6000L water flow (varies for different water qualities)
Packaging: One set/color box, 6 sets/carton
Carton size: 510*510*390mm (20*20*15¼in)
Machine Parts Diagram
A. Water output
B. UF membrane Filter
C. Composite filter
D. Machine housing
E. Base pad
F. Water output connector
G. Pipe
H. Connector nut
I. Connector adapter
J. Silicon gasket
K. Stainless steel net
L. Connector Head
M. Multi-function joint
N. Connector adapter key
2
Inner Packing Details
Other s
A. Machine body (1 PC)
B. Connector head
C. Parts and accessories
Connector adapter 4pcs, multi-function joint 1 pc, adapter
key 1 pc
Inner Packing Details
Safety Warnings
3
Safety Warnings
The feed water of the machine must be higher or equal quality
of municipal tap water.
Please let the output water flow for about 15 seconds before
using the purified water.
Please let the output water flow for at least 1 minute if you
didn’t use the machine for more than 2 days.
Please replace your filter if the water outflow is significantly
slower.
Please use the machine under available source water pressure
(10.15-50.76 PSI). Please adjust your source water pressure if
it is too high, otherwise it will cause damage to the machine.
Please don’t clean the body of the machine with corrosive liquid
or detergent.
Avoid setting machine under direct sunlight, as damage may
occur.
F.
E.
D.
C.
B.
A.
G.
4
Installation
Other s
Install Type A Connection Adapter
(Suit for Screw Tap as Diameter 21.5mm or 23.5mm)
1. Dismount the nut from
the faucet
2. Choose the suitable
adapter
3. Put the nut mounting in upward,
install the outer thread adapter
with faucet
4. Screw down the
connector head into the
connector, then
connect the machine
hose.
5. When install is complete allow
water to run through the system.
Inspect all connections, and verify
no leaks are present.
Installation
Installation
5
Installation
Install Type B Connection Adaptor
(Suit for Screw Tap as Diameter 20.5mm or 22.5mm)
Pipe Connection of the Main Machine Head
1. Dismount the nut from
the faucet
2. Take off the faucet diverter and
choose the suitable adaptor
3. Put the nut-mounting in upward,
install the inner thread adapter
with faucet
4. Screw down the
connector head into the
connector then connect
the machine hose
5. When install is complete allow
water to run through the system.
Inspect all connections, and verify
no leaks are present.
6
Replacement of the Battery
Functions Instructions
A. Pull out the back cover of the battery box
B. Open the cover of the battery box
C. Remove batteries from the battery jar
D. Place the new batteries into the battery jar
E. Put the battery pack back into the machine housing
F. Close the back cover
A. After installing the battery, the LCD screen will illuminate
B. It will show 6000 on the screen (it means the life of the UF
membrane filter has 6000L of water flow)
C. The display will turn off if there is no water flow through the
machine
D. It will turn on again when the water flow is turned on
E. When the voltage capacity is less than 2.6V, it will show low
voltage on the screen and will disappear after replacing the
battery
Replacement
Replacement
3
Replacement of the Filter Cartridges
How to replace the filter cartridges?
Before beginning point water output pipe to halfway down
A. Align the tabs on the water output with the tabs on the housing.
B. Put tab into unlock position
C. Rotate the water output pipe counter-clockwise
D. Pull out the filter cartridges
E. Rotate the water output pipe clockwise
F. The filter cartridges and the water output pipe are now
separated
G. Now connect the new filter cartridges to the water output pipe
H. Rotate the water output pipe counter-clockwise
I. Once secured put the output pipe back into the machine body
J. Rotate the water output pipe clockwise
* Push in the snap joint once secure*
Troubleshooting
8
The head of the machine
(Leaking)
The head of the Connection
pipe (Leaking)
1. Did not install the faucet
in right way
1. Install again
2. Repair the faucet
Please connect it again
2. The head of the faucet is
broken or damaged. The
seal ring is broken
The head of the pipe is not
connecting well
The main body of the
machine (Leaking)
Please check and connect
again.
The inner connections pipe
of the machine is loose.
Tap water faucet flow is
coming out slow
Clean the net of the faucet
1. The tap water filter net
was blocked
The hydrogen water
output pipe flow is
coming out slow
1. Verify pipe is fully extended1. The water output pipe is
not in flow position.
The purified water has a
bad smell or taste
Replace the filtersThe life of the filter has
expired
If the Pipe is not the
problem, replace with a
new filter
The filter inside is clogged
The source water outlet
is dirty
Change the seal ring if
the seal ring is broken
Problems Reasons Solutions
Troubleshooting
Table des matières
