Hussmann VR3-M Series Manuel utilisateur

/SPECIALTY

USER MANU A L

MERCHANDISER

VR3-M/HV-M MEAT SERVICE

VR3 - VR3-M/F-4-R

- VR3-M/F-6-R

- VR3-M/F-8-R

- VR3-M/F-12-R

- VR3HV-M/F-4-R

- VR3HV-M/F-6-R

- VR3HV-M/F-8-R

- VR3HV-M/F-12-R

- VR3HV-M/F-10-R Remote

22018

General Information 3

Case Sections 4

Installation 5

Unloading

Receiving Case 5

Snapping Chalk Lines 5

Placement 6

VR3 Lifting and Transport Instructions 7

Front Body Panel Install

Fasten Rear Body Panel Install

Leveling

Leveler Adjustment 8

Leg Adjustment 8

Joining

Parts List

Arm Adjustment 12

Glass Adjustment 13

Refrigeration 16

Piping

Refrigerant 16

Refrigerant Piping 16

Line Sizing 16

Oil Traps 16

Piping Schematic 17

Refrigeration Spec Sheets 20

DOE 2017y

Compliant .

Table of Contents

Electrical 22

Electrical Info

Merchandiser Electrical Data 22

Electrical Connections 22

Field Wiring 22

of Wiring 22

Remove Rear Raceway 23

Electrical Conduit (Electrical Box) 23

Electrical Wiring Diagram 24

User Information 33

General

Start Up 33

Load Limits 33

Basic Operation 33

Operation 34

Baseline Settings 34

Case Switches 34

Merchandising Requirements 35

Merchandising DON’TS 36

Maintenance

Case Cleaning 37

Exterior Surfaces 37

Interior Surfaces 37

Troubleshooting 39

Hussmann refrigerated merchandisers conﬁgured for sale for use in the United States

meet or surpass the requirements of the DOE 2017 energy eﬃciency standards.

Case Descripon:

Description: Refrigerated Service Meat Merchandiser

Shipping Damage: All equipment should be thoroughly examined for shipping damage before and

during unloading. This equipment has been carefully inspected at our factory and the carrier has

assumed responsibility for safe arrival. If damaged, either apparent or concealed, claim must be

made to the carrier Immediately.

Apparent Loss or Damage: If there is an obvious loss or damage, it must be noted on the freight bill

or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The carrier

will supply necessary claim forms.

Concealed Loss or Damage: When loss or damage is not apparent until after all equipment is

uncrated, a claim for concealed damage is made. Make request in writing to carrier for inspection

within 15 days, and retain all packaging. The carrier will supply inspection report and required claim

forms.

Shortages: Check your shipment for any possible shortages of material (See Parts List page 11). If

a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann

Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an

inspection. Hussmann Chino will acknowledge shortages within ten days from receipt of equipment.

Hussmann Chino Product Control: The serial number and shipping date of all equipment have been

recordedinHussmann’slesforwarrantyandreplacementpartpurposes.Allcorrespondence

pertaining to warranty or parts ordering must include the serial number of each piece of equipment

involved, in order to provide the customer with the correct parts.

Location/Store Conditions: The VR3HV-M/F-EP refrigerated merchandiser has been designed for use

only in air conditioned stores where temperature and humidity are maintained at or below 75°F Dry

bulb and 55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or

windows (etc.) to create air currents around the merchandiser, as this will impair its correct operation.

This equipment is to be installed

to comply with the applicable

NEC, Federal, State , and Local

Plumbing and Construction

Code having jurisdiction.

AT TENTION

INSTALLER

/CHINO

A publication of HUSSMANN®Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 592-2060

Keep this booklet with the case at all times for future reference.

General Information

Case Sections

Installation

NOTICE

Do NOT remove Foam Blocks from shelves

and glass until the merchandisers are

positioned for installation. Shelves or

merchandising glass may be damaged.

Loose

Items

Warning

Labels

Foam Blocks

in place Boards

fastened

Case is to arrive at store as was shipped form

factory. See reference above for proper shipment

referencing. (Not actual case)

Receiving Case

Upon receiving your new Hussmann Case all

equipment should be thoroughly examined for

shipping damage before and during unloading.

This equipment has been carefully inspected at

our factory. Any claim for loss or damage must

be made to the carrier. The carrier will provide

any necessary inspection reports/ or claim form.

If there is obvious loss or damage, it must be

noted on the freight bill or express receipt and

signed by the carrier’s agent; otherwise carrier

may refuse claim.

Snapping Chalk Lines

Preparepermanentpositioningbymarkingoors

with Chalk snap lines where cases are to be

located. Chalk lines are to run along the base or

legs of cases.

Placement

Important: See lifting instructions to properly lift

case when being placed on dollies or permanent

location. (See page 7 for Lifting Instructions.)

Leaveallhardwareandttingsinplaceuntil

case is located at or near its preferred location.

Using a J-Bar lift the case from the 2x4 boards

and placing dollies underneath each Base Leg,

proceed to moving the case to its designated

location if not done so already.

IF APPLICABLE

(NOT ALL CASES CONTAIN LEG BRACES)

The Illustration Below demonstrates perfect

placement of a dollie per 1 side for both Base

Legs of the merchandiser.

IF APPLICABLE

(NOT ALL CASES

CARRY LEG BRACES)

Installation (cont’d)

Movethextureascloseaspossibletoitsper-

manent location and then remove all packag-

ing and prepare to remove off Skid. Remove all

separately packed accessories such as kits, and

panels. Check for damage before discarding

packaging.

Remove screws as well as fastened plates

bolted to each 2x4 board at each base leg.

Remove fastened plates only upper Brace Legs

are to remain fastened onto case.

Fastened plate

Once the fastened plates are removed a J-Bar

can be used to lift at each end of the Leg Braces

to remove the below 2x4 boards.

VR3HV-M/F Lifting and Transport

Instructions

1. The VR3HV-M/F can be lifted by a forklift at

typical lifting points.

Forklift Points

(Underneath Deck)

WARNING

Improper placement of forks may damage

drainage piping. Use a spotter when placing

forks. Make sure that piping will not be dam-

aged. Use J-Bars or Jacks if forks cannot be

used safely

2. Ensure lower body panels are removed be-

fore lifting with a forklift. Serious damage will

occur if the body panels are not removed.

3. Make sure that fork spacing and width will not

damage drain or come in contact with piping,

or electrical lines

4. Be sure that the forks are long enough to

support beyond the center of the case but not

damage near components. Check for proper

balance before moving. A minimum fork

length of 36” is recommended for 68” wide

cases

Installation (cont’d)

5. The VR3HV-M/F merchandiser can be raised

at one end underneath the deck with a forklift

to allow the placement of rollers or dollies.

6. Evenly support the entire base structure on

rollers or dollies before attempting to move.

Each Base Leg must have its own dollie to

properly support the case.

Lifting Points are typical and dependent upon

size of case and refrigeration application, drain-

agecongurationswillcallforaltercationsin

Lifting Zones.

Belowarethefollowingdrainagecongurations

and lifting should be altered to the expected

model.

VR3HV M/F Drain Location

Service Drain

Bottom Drain

Installation (cont’d)

Leveler Adjustment

Position the case at the highest point. Set a long

magnetized level (4ft [1220 mm] or more) on

either underneath the deck or on top of the case.

Ensure to level case from front to back and side

to side.

Level

(4 ft[1220mm])

Leg Adjustment

Adjust the legs at each corner of the case to

level out any discrepancies in order to optimize

case performance and proper drainage.

Note:Toavoidremovingconcreteooring,begin

line up levelling from the Highest point of the

storeoor.

A wrench or pliers may be used to adjust each

base leg.

• Turning the base of each leg clockwise will

raise the height of the case.

• Turning the base of each leg

counterclockwise will lower the height of the

case.

Level

(4 ft[1220mm])

Installation (cont’d)

Setting and Joining

The sectional construction of these models en-

able them to be joined in line to give the effect of

one continuous display.

An Alignment pin kit is supplied with every case

and must be used in alignment.

Leveling

IMPORTANT! IT IS IMPERATIVE THAT CASES

BE LEVELED FROM FRONT TO BACK AND

SIDE TO SIDE PRIOR TO JOINING. A LEVEL

CASE IS NECESSARY TO INSURE PROPER

OPERATION, WATER DRAINAGE, GLASS

ALIGNMENT AND OPERATION OF THE HING-

ES SUPPORTING THE GLASS. LEVELING

THE CASE CORRECTLY WILL SOLVE MOST

HINGE OPERATION PROBLEMS.

1. Using case blueprints, measure off and mark

ontheoortheexactdimensionsofwherethe

cases will sit. Snap chalk line for front and back

positions of base rail or pedestal. Mark the loca-

tion of each joint front and back. Find the high-

est point throughout the lineup. FLOORS ARE

NORMALLY NOT LEVEL! Determine the highest

pointoftheoor;caseswillbesetoffthispoint.

All cases in the entire lineup must be brought up

to the highest level of the case sitting at the high-

est point in the lineup.

2.Setrstcaseoverthehighestpartoftheoor

and adjust legs so that case is level.

ALIGNMENT PINS

CASE BOLTING

LOCATION

SILICONE

SEALANT AREA

Installation (cont’d)

3.Setsecondcasewithinonefoot(1’)oftherst

case. Keep the supports along the length of the

caseandfarendofcase.Levelcasetotherst

using the instructions in step one.

4. Apply liberal bead of case joint sealant (bu-

tyl)torstcase.Sealantareaisshownusinga

dotted line in illustration. Apply heavy amount to

cover entire shaded area.

It is the contractor’s responsibility to install

case(s) according to local construction and

health codes.

ATTENTION

INSTALLER

5. Apply liberal bead of case joint sealant (bu-

tyl)torstcase.Sealantareaisshownusinga

striped line in illustration in page 16. Apply heavy

amount to cover entire shaded area.

6.Slidesecondcaseuptorstcasesnugly.

Thenlevelsecondcasetotherstcasesoglass

front,bumperandtopareush.

Do not use bolts to pull cases together.

< 1’

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hussmann marchandiseur

Hussmann

Hussmann VBL Manuel utilisateur

Hussmann

Hussmann impact C5-LE Mode d’emploi

Hussmann

Hussmann CW2U-138GE Manuel utilisateur

Hussmann

Hussmann Q1-DC Wedge Mode d’emploi

Hussmann

Hussmann D6NX-LEP Mode d’emploi

Hussmann

Hussmann FHM Manuel utilisateur

Hussmann

Hussmann SCSS Mode d'emploi

Hussmann

Hussmann IMPACT LWUG Mode d’emploi

Hussmann

Hussmann SHVS Mode d'emploi

Hussmann

Hussmann HGM-3 BS Manuel utilisateur

Hussmann

Hussmann GGSM Guide rapide

Hussmann

Hussmann Impact Excel C6X-E Mode d’emploi

Hussmann

Hussmann LBN Guide rapide

Hussmann

Hussmann VSG Mode d'emploi

Hussmann

Hussmann IMPACT RLT Mode d’emploi

Hussmann

Hussmann Impact Excel M1X-GE Mode d’emploi

Hussmann

Hussmann IMPACT D5R Manuel utilisateur

Hussmann

Hussmann IMPACT ED1 Manuel utilisateur

Hussmann

Hussmann ARL Manuel utilisateur

Hussmann

Hussmann Impact P1X49-MOB-B Manuel utilisateur

Hussmann

Hussmann G5 Guide rapide

Hussmann

Hussmann IMPACT D5ELE Guide de démarrage rapide

Hussmann

Hussmann Impact M1GE Manuel utilisateur

Hussmann

Hussmann IMPACT D5L Manuel utilisateur

Manuels marchandiseur populaires d'autres marques

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuel utilisateur

EPTA

EPTA COSTAN RHINO MULTI Manuel utilisateur

CASCO

CASCO Nano Cube Manuel utilisateur

True

True GDIM-26 Manuel utilisateur

Structural Concepts

Structural Concepts Oasis Mobile Series Instructions d'installation

Haussmann

Haussmann RL Manuel utilisateur

Howard McCray

Howard McCray R-CDS32E-4 Manuel utilisateur

EPTA

EPTA iarp Cool Emotions Delight Lite Manuel utilisateur

VALERA

VALERA BC 85 Manuel utilisateur

HL Display

HL Display 3eBin Manuel utilisateur

Dixie Narco

Dixie Narco DNCB 501E Manuel utilisateur

APW Wyott

APW Wyott Racer DMXD-30H Manuel utilisateur

Hoshizaki

Hoshizaki KD-90C Manuel utilisateur

Summit

Summit SCR1006 Manuel utilisateur

Delfield

Delfield Shelleyspeed SPM-28E Manuel utilisateur

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuel utilisateur

Kysor/Warren

Kysor/Warren GranBering KW Mode d’emploi

Crane

Crane BevMAX Refresh 6 Media Manuel utilisateur