Hussmann NIM Manuel utilisateur

SERIES NIM

Low Temperature

Merchandisers

PLEASE READ THIS MANUAL BEFORE USING THE PRODUCT

Installation &

Operation Manual

P/N 2402195

NIM-6

January 2003

Hussmann Monterrey, Mexico

Carretera Mexico-Laredo KM. 1009

Cienga de Flores, Nuevo Leon 65550

Mexico

Phone: (52) 81-8318-6400

Fax: (52) 81-8318-6496

TABLE OF CONTENTS

Page

Introduction 1

Inspection 1

Location 1

Clearance 1

Shipping Braces 1

Placement of Doors 1

Leveling of the Cabinet 2

Sealing Splashguard to Floor 2

Grills 2

Drain 3

Tempered Glass Doors 3

DisplayPan 3

Air Distribution 3

Electric connections 4

Serialplate 4

Control of temperature 4

Defrost time Clock 4

Maintenance 5

Technical Data Sheets 5

IMPORTANT

KEEP IN STORE FOR FUTURE REFERENCE

INTRODUCTION

The NIM – 6 and NIM-4 are low temperature self-contained cabinets, designed for pre-packaged frozen foods

or Novelty Ice Cream products.

Design features include self closing glass doors, CFC Free insulating foam, low rail height for ease of access,

and a balanced refrigeration system for optimum energy savings.

INSPECTION

a) General

All the cabinets should be thoroughly examined to detect damages before and during unloading from the

delivering carrier.

This cabinet has been inspected carefully at our factory. Any claim for loss or damage must be made to the

carrier. The carrier will provide any necessary inspection reports and/or claim forms.

b) Apparent Loss or Damage

If there is an obvious loss or damage, it must be noted on the freight bill or express receipt and signed by the

carrier’s agent; otherwise, carrier may refuse claim.

c) Concealed Loss or Damage

When loss or damage is not apparent until after the cabinets is uncrated, retain all packing materials and submit

a written request to the carrier for inspection, within 5 days.

LOCATION

Avoid locating where the light of the sun is direct, where air conditioning grills exist, or near electric fans,

doors, and open windows, that can create currents of air around these cabinets.

CLEARANCE

To prevent sweating on the exterior surfaces, there must be a minimum clearance of 4in. (102mm) between

merchandisers, other fixtures and store walls.

SHIPPING BRACES

Move the cabinet as close as possible to its permanent location and then remove all packaging. Check for

damage before discarding packaging. Remove all separately packed accessories such and kits.

PLACEMENT OF DOORS

The case doors are packed in cabinet. Install them in the following manner:

1. Install the left door first (interior).

2. Hook the door in the right interior upper corner with the hooks of automatic closing mechanism and push

toward the right. (fig.1)

3. Place the top in the interior upper rail leaving at an angle (fig 2.)

4. To align, push up and in to the back bottom rail (fig. 3)

5. Place the right or external door in the same way

LEVELING OF THE CABINET

Cabinets must be installed level to ensure proper operation of the refrigeration system and to ensure proper

drainage of defrost water. When leveling merchandisers, use a carpenter’s level as shown

SEALING SPLASHGUARD TO FLOOR

If required by local sanitation codes, or if desired by the customer, stainless steel splashguards may be sealed to

the floor using a vinyl cove base trim. The size of trim needed will depend on how much the floor is out of

level.

To install the trim to the splashguard:

1. Remove all dirt, wax and grease from the area of the splashguard where adhesion will be necessary.

This is to ensure a good and secure installation.

2. Apply a good contact cement to the cove trim and allow proper drying time according to the directions

supplied with the cement.

3. Install the trim to the splashguard so that it is lying flush with the floor. DO NOT SEAL THE TRIM

TO THE FLOOR.

4. If required by local health codes the cove Trim may be sealed to the floor, using a silicone-type sealer.

Sealant must be removed and replaced when servicing the case condensing unit area.

GRILL

The grill provides access to the condenser unit and the box which contains the electric connections. The grill is

fastened with screws for initial shipping.

DRAIN

The cabinet is provided with a drain installed from the manufacturer; this drainage runs from the bottom of the

cabinet to a condenser pan located in the condensing unit area. The system is designed to evaporate the

condensate water. It is important to keep this pan clean and free of debris so that it dissipates the water

efficiently in order to prevent overflows.

DOORS OF TEMPERED GLASS

The doors are manufactured with tempered glass mounted on PVC frames. The Self-closing design assists in

maintaining stable interior temperatures and saves energy by preventing warm air from entering into the case

interior. Periodic cleaning of the doors and tracks assists in keeping the doors closing properly.

DISPLAY PANS

The NIM-6 is provided with 3 display pans which you should make sure are placed correctly and never operate

the cabinet without these. If you use the case without these display pans the interior airflow and temperature in

the cabinet will be adversely affected

AIR DISTRIBUTION

The NIM-6 and NIM-4 cabinets are sensitive to air disturbances. Air currents passing around cabinets will

seriously impair their operation. DO NOT allow air conditioning, electric fans, open doors or windows, etc. to

create air currents around the cabinets.

LOAD LIMITS

Each merchandiser has a load limit decal. Shelf life of perishables will be short if load limit is violated.

Overstocking will adversely affect product temperature and cabinet efficiency.

ELECTRIC CONNECTIONS

It is very important for your safety and that of your customers that this cabinet be grounded. A qualified

electrician must make the electrical installation, in accordance with the national or local electric codes.

NOTE: Connecting this cabinet to any electric supply other than specified on the serial plate, will void the

warranty and it can cause severe damage to the unit.

WARNING

Always disconnect the electrical power at the main disconnect when servicing or replacing any electrical

component. This includes, but is not limited to, such items as fans, heaters, thermostats and lights.

HONEY

COMB

DISCHARGE

PAN

DISPLAY

TEMPERATURE

CONTROL

DOORS GLASS

TEMPERED

SERIAL PLATE

The serial plate is located inside the cabinet. It contains the necessary information for the appropriate electric

installation. Do not remove the serial plate under any circumstance.

CONTROL OF TEMPERATURE

The cabinet has an electronic control for control of case interior temperature. It is installed in the lower part of

the cabinet. To locate it remove the grills. This control is programmed from the manufacturer for proper

freezing temperatures.

DEFROST TIME CLOCK

The Defrost Time Clock comes programmed from the factory. Defrost is set for every 24 hours for a duration of

50 minutes.

MAINTENANCE

Long life and satisfactory performance of any equipment is dependent upon the care it receives. To ensure long

life, proper sanitation and minimum maintenance costs, these merchandisers should be thoroughly cleaned, all

debris removed and the interiors washed down periodically.

Exterior Surfaces

The exterior surfaces should be cleaned with a mild detergent and warm water to protect and maintain their

attractive finish. NEVER USE ABRASIVE CLEANSERS OR SCOURING PADS.

Interior Surfaces

The interior surfaces may be cleaned with most domestic detergents, ammonia based cleaners and sanitizing

solutions with no harm to the surface.

Condenser

The condenser needs to be cleaned regularly. A dirty condenser restricts the airflow, causing loss in the

efficiency of the refrigeration system. (A regular schedule should be established to clean it frequently).

Prior to cleaning make sure that the case plug is disconnected from the outlet.

1) Use a stiff bristle brush to remove debris.

2) A vacuum cleaner may also be necessary to assist with removing dust and dirt.

3) If the cabinet is located in a susceptible area where the condenser is greased, clean the with a solution of

lukewarm water and detergent. Be careful that the solution doesn't come in contact with wiring or electric

components.

4)The thermostat in position TURNED OFF only disconnects the condenser unit. The compressor will be

energized until the cabinet is disconnected from the electric outlet.

When cleaning the condenser be careful as the fins may have sharp edges.

Routine maintenance

a) Verify that the blades of the evaporator and condenser motors rotate freely and that the motors work

correctly.

b) Verify that the drainage is not obstructed and the hoses in the condenser pan avoid spills of water after

defrost

c) Makes sure that the doors close easily and seal well

d) Make sure the discharge honeycomb and the return grill are free of ice. The discharge honeycomb is

removable for cleaning.

TECHNICAL DATA SHEETS

The data sheets are enclosed with this manual inside the cabinet. The data sheets contain electric specifications

of the cabinet, electric diagrams, lists of parts and operation data.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hussmann marchandiseur

Hussmann

Hussmann Impact M1GLE-93 Manuel utilisateur

Hussmann

Hussmann JVMRS Manuel utilisateur

Hussmann

Hussmann Impact C2-XLE Mode d’emploi

Hussmann

Hussmann P1X50-EP Mode d’emploi

Hussmann

Hussmann Impact Excel B3XC-LEP Mode d’emploi

Hussmann

Hussmann RGDC Manuel utilisateur

Hussmann

Hussmann Impact Excel M5X Manuel

Hussmann

Hussmann IMPACT M4 Manuel utilisateur

Hussmann

Hussmann HEDN Mode d’emploi

Hussmann

Hussmann VR3-M Series Manuel utilisateur

Hussmann

Hussmann impact Excel C5X-LE Mode d’emploi

Hussmann

Hussmann IMPACT M5NGE Manuel utilisateur

Hussmann

Hussmann D5X-HE Mode d’emploi

Hussmann

Hussmann VBL Manuel utilisateur

Hussmann

Hussmann LG Mode d’emploi

Hussmann

Hussmann M1X-EP Mode d’emploi

Hussmann

Hussmann Specialty ProductsCR3FO Mode d’emploi

Hussmann

Hussmann IMPACT D5RRI Manuel d'utilisation

Hussmann

Hussmann SSGT Manuel utilisateur

Hussmann

Hussmann D6NX-LEP Mode d’emploi

Hussmann

Hussmann FM Manuel utilisateur

Hussmann

Hussmann MWG Manuel utilisateur

Hussmann

Hussmann RI4 Mode d’emploi

Hussmann

Hussmann IMPACT M2GE Manuel utilisateur

Manuels marchandiseur populaires d'autres marques

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuel utilisateur

EPTA

EPTA COSTAN RHINO MULTI Manuel utilisateur

CASCO

CASCO Nano Cube Manuel utilisateur

True

True GDIM-26 Manuel utilisateur

Structural Concepts

Structural Concepts Oasis Mobile Series Instructions d'installation

Haussmann

Haussmann RL Manuel utilisateur

Howard McCray

Howard McCray R-CDS32E-4 Manuel utilisateur

EPTA

EPTA iarp Cool Emotions Delight Lite Manuel utilisateur

VALERA

VALERA BC 85 Manuel utilisateur

HL Display

HL Display 3eBin Manuel utilisateur

Dixie Narco

Dixie Narco DNCB 501E Manuel utilisateur

APW Wyott

APW Wyott Racer DMXD-30H Manuel utilisateur

Hoshizaki

Hoshizaki KD-90C Manuel utilisateur

Summit

Summit SCR1006 Manuel utilisateur

Delfield

Delfield Shelleyspeed SPM-28E Manuel utilisateur

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuel utilisateur

Kysor/Warren

Kysor/Warren GranBering KW Mode d’emploi

Crane

Crane BevMAX Refresh 6 Media Manuel utilisateur