Huskie Tools SP-24 Mode d’emploi

HUSKIE TOOLS, INC.

Operating Instruction Manual

For SP-24 Hydraulic Cutters

With Parts List

http://www.huskietools.com [email protected]2

http://www.huskietools.com [email protected]1

GENERAL INFORMATION GUIDE FOR SP-24 CUTTER

The following steps are guidelines for safe operation of the Huskie cutters. Please take the time to review them as these

are helpful hints that have been accumulated over the years.

1. Stay within the maximum cutting limits of each tool as listed on page 5.

2. Try to keep the cutter head clean. When cleaning, use a spray lubricant to avoid a build up of dirt and sand

which will damage the cutter head.

3. Stop pumping when the blade reaches the extreme end of its advance. If the material being cut (usually wire

rope or soft cables) seems to be cut but does not break free of the tool, this indicates that the blade is jammed on

a small piece of cable. Refer to “troubleshooting” on page three to free the blade.

4. All Huskie tools require proper care. Occasional cleaning and degreasing in solvent, and sharpening blade and

cutter head, will keep these tools operating without problems.

5. The most common problem encountered is blade breakage. Ninety-nine percent of all breakage occurs

because the cutter head is not securely latched before cutting. If the latch is not secured, the blade will push

open the cutter head and damage both the body head and blade. This causes the outside ear of the blade to break

on an angle. In some cases the whole cutter head may crack in half. Cutting material that is not specified may

also cause blade damage. In time these blades will fatigue and crack and must then be replaced.

6. There may be a residue of oil present on new tools when they are removed from the original shipping container.

This is to protect the tool from corrosion during shipment and storage, and should not be considered defective.

The tool can be cleaned with a spray degreaser or soapy water.

7. If tool is jammed, avoid beating directly on the tool with a hammer, especially avoid flattening the piston

cylinder. Use a hammer in conjunction with a block of wood or soft material to free the blade.

8. All tools can be reconditioned and overhauled. Call factory and obtain an RGA # for returning tools.

http://www.huskietools.com [email protected]2

9. If the cutters are used under water, wash them down and lubricate after each use. This whole operation takes less

than five minutes. It may be helpful to paint new tools with a light color, corrosion resistant paint.

10. Always return tools to their carrying bag to protect them from sand and dirt. Extra bags can be purchased.

11. Always carry a spare blade, preferably attached to the carrying bag.

12. Use clear hydraulic fluid MV-32 available from your dealer or HTI.

13. When cutting, keep area clear of spectators as hardened metals may fly apart when severed.

14. Always cut the material at a 90 degree angle to the blade. Any other angle may cause the blade and head shear

to fracture. See illustration below.

GENERAL INFORMATION GUIDE FOR SP-24 CUTTER

http://www.huskietools.com [email protected]3

TROUBLESHOOTING GUIDE

1. Problem: Small wire strands or pieces of cable or debris get jammed between the cutter head and blade, not allow-

ing the blade to retract.

Solution: A) Hold release lever down while tapping on the ram with a block of wood and a hammer. If this does

not work or tool continues to hang up, proceed to step “B”.

B) Remove blade screw and release the ram. Then disassemble cutter head and remove burrs from both blade and

head shear, using a flat grinding stone on the rolled edge. Do not sharpen like a knife – leave cutting edge flat!

See illustration on page 2.

2. Problem: Blade is advanced under pressure with no load and the release lever seems to be stuck.

Solution: A) Use both hands to depress lever using body weight and the ground or other strong surface for support.

If this does not work, proceed to step “B”.

B) Lay tool flat on the ground or other strong surface and hit release lever with a block of wood and a hammer to

release pressure.

3. Problem: Tool will not advance when handle is pumped.

Solution: A) Remove body handle and check oil reservoir for proper fluid level. The oil should be to the top of the

reservoir when the cap is removed. Be sure the tool is fully retracted before removing cap.

Solution B) After storing for a long period of time, or occasionally when the tool is new, a check ball may be stuck

not allowing it to advance. Invert the tool and rap the cutter head sharply on the ground. Do this several times, then

pump handle to advance the blade.

http://www.huskietools.com [email protected]4

OPERATING INSTRUCTIONS FOR ALL “SP”

SERIES HYDRAULIC CUTTERS

1. Before cutting, make sure the material being cut is within the proper cutting capacity of the tool being used.

2. Before connecting the tool head, make sure the pump and hose being used is working properly, and adjusted to

and rated at 10,000 psi. The use of a pump or hose that is not rated for 10,000 psi working pressure may cause

severe tool damage and result in personal injury.

3. Connect the tool head to the pump or hose, making sure all coupler connections are secure. It is important that

all connections are tight for tool to function properly.

4. Open cutter head by lifting latch or removing lock pin. Depending on the model being used.

5. Insert material between cutter head and blade and secure latch. It is important that you check the latch for proper

engagement before continuing with the cut. Failure to secure the latch can result in severe tool damage and

personal injury.

6. Align the material at a 90 degree angle to the blade. This will ensure a proper cut with minimal distortion. If the

material is cut at any other angle, severe blade damage may occur. Refer to diagram on page two for proper

alignment.

7. Proceed by operating pump to advance blade. If the pump has a hold feature, it is important to check for proper

alignment of material and blade before cutting. Continue to operate pump and cut material.

8. Once the cut is made stop the pump and release pressure to retract the blade. It is not necessary to advance the

tool any further after the cut has been completed. If the tool blade hangs up, be sure to check if coupler

connections are tight, release mechanism on pump is functioning properly, or refer to page three

“troubleshooting” to release blade.

9. Always wear eye protection and any other specified safety equipment when cutting. Be sure surrounding area is

clear, as hardened metals may fly apart when severed.

10. For EHS guy wire or bridge strand, use models SP-24CC, S-24CC or S-32CC only! The use of any other

SP-series cutter will result in severe blade damage and may cause personal injury.

11. Models SP-85 and SP-100 are designed for use on non-ferrous metals only! Do not cut steel or severe tool

damage and personal injury may occur.

http://www.huskietools.com [email protected]5

SP SERIES SPECIFICATIONS

SP-20 SP-24 SP-32 SP-40 SP-55 SP-85 SP-100

output 4.4 ton output 7.8 ton output 20 ton output 6.28 ton output 13.12 ton output 2.7 ton output 8.3 ton

weight 3 lbs weight 5 lbs weight 19 lbs weight 7.2 lbs weight 18 lbs weight 11 lbs weight 27 lbs

size 5"Lx3"W size 11"Lx3.5"W

size 14"Lx3.25"W

size 12"Lx4"W size 15"Lx4.5"W size 19"Lx5"W size 24"Lx6"W

Wire 20mm 22mm 32mm Do not cut 26mm Communication 100mm

Ropes 9/16" 7/8" 1-1/4" 1" cables 3.35" 4"

Soft Steel 14mm 20mm 32mm 16mm 32mm Lead sheath 100mm

Bolts 9/16" 3/4" 1-1/4" 5/8" 7/8" cables 3.35" 4"

Rebar, 13mm 16mm 26mm 16mm 20mm Soft CU & AL 89mm

ground & 1/2" 5/8" 1" 5/8" 3/4" cables 3" 3-1/2"

anchor rod

ACSR 20mm 22mm 32mm 40mm 50mm

3/4" 7/8" 1-1/4" 1-1/5" 2" DO NOT CUT

Standard 14mm 16mm 22mm 16mm 20mm

*Guy 1/2" 5/8" 7/8" 5/8" 5/8" DO NOT CUT

strand

http://www.huskietools.com [email protected]6

MODEL SP-24 PARTS DIAGRAM

http://www.huskietools.com [email protected]7

MODEL SP-24 PARTS LIST

1 M8 Hex. Nut 40-24 8

2 M8 Lock Washer 40-25 8

3 Main Head 24-02 1

4 Spacer 24-03 1

5 Head Shear 24-04 1

6 Stud Bolt (21) 24-05 4

7 Slide Pin 20-71 1

8 Spring (144) 85-37 1

9 2 X 10 Drive Pin (AW) 5-09 1

10 Pin (142) 24-06 2

11 CE-10 Snap Ring 40-16 4

12 Latch 24-07 1

13 Blade 24-08 1

14 M5 X 5 Screw (C.P.) RD-16 1

15 Cylinder Head P24-01 1

16 Spring (379) P24-02 1

17 Ram P24-03 1

18 Blade Screw 16-19 1

19 P-34 Back-Up Ring (B.C.) 85-22 1

20 P-34 O-Ring 85-23 1

21 Cylinder P24-04 1

22 Female Coupler IZUMI 100-24 1

Adapter 3/8" PT-M. 3/8" NPT-

P85-80 1

24 Female Coupler P.H. Type P85-81 1

DESCRIPTION

QTY.

CODE

QTY.

NO.

CODE

NO.

DESCRIPTION

All Huskie REC-Series battery driven products carry a 5 year warranty, and the ECO-Series

carry a 3 year warranty. The BP-70E, BP-70EI, and the BP-70MH batteries carry a 5 year

warranty from the date stamped on the battery. The LED indicator on the BP-70-EI battery

carries a 1 year warranty from purchase date. Hydraulic hammers carry a one year warranty

and all other Huskie products carry a 5 year warranty. Huskie reserves the right to determine

all warranty claims. Failure due to misuse, abuse or repairs attempted by anyone other than

Huskie Tools, Inc., or an authorized service center render this warranty null and void. Our

patented drop-out bypass cartridge can be re-calibrated or tested at no charge for the life

of the tool. All factory repaired or reconditioned hydraulic tools carry a one year warranty

on parts and labor.

REPAIR AND WARRANTY CLAIMS

All claims must be sent to Huskie for inspection and authorization. A Return Goods

Authorization is required before shipping tools to Huskie. Secure the authorization by

telephoning 1-800-860-6170 or writing to Huskie's main office with details of claim. Non-

warranty repairs are handled using the same procedure. Repairs exceeding 50% of the cost

of a new tool will be advised before repairs are made.

PLEASE RETAIN FOR YOUR RECORDS

Purchaser’s Name _____________________________________________________

Address _____________________________________________________

City, State, Zip _____________________________________________________

Tool Model Number _____________________________________________________

Serial Number _____________________________________________________

Date Purchased From _____________________________________________________

Purchased From _____________________________________________________

MODEL SP-24 WARRANTY

Table des matières

Autres manuels Huskie Tools Coupeur

Huskie Tools

Huskie Tools SL-S20 Manuel utilisateur

Huskie Tools

Huskie Tools REC-54ACM Manuel utilisateur

Huskie Tools

Huskie Tools REC-S624CC Manuel utilisateur

Huskie Tools

Huskie Tools 7M PRO LINE Series Manuel utilisateur

Huskie Tools

Huskie Tools RCC-MK754ACM Manuel utilisateur

Huskie Tools

Huskie Tools PRO LINE REC-MK730Y Manuel utilisateur

Huskie Tools

Huskie Tools S-20 Mode d’emploi

Huskie Tools

Huskie Tools S-240 Manuel utilisateur

Huskie Tools

Huskie Tools REC-S640 Manuel utilisateur

Huskie Tools

Huskie Tools REC-5OU Mode d’emploi

Huskie Tools

Huskie Tools REC-5OM Mode d’emploi

Huskie Tools

Huskie Tools REC Series Manuel utilisateur

Huskie Tools

Huskie Tools SP-40 Mode d’emploi

Huskie Tools

Huskie Tools REC-634YC Manuel utilisateur

Huskie Tools

Huskie Tools REC-660YC Manuel utilisateur

Huskie Tools

Huskie Tools Pro Line 7 Series Manuel utilisateur

Huskie Tools

Huskie Tools ECO-MK7500 Manuel utilisateur

Huskie Tools

Huskie Tools ECO-336A Manuel utilisateur

Huskie Tools

Huskie Tools REC-54M Mode d’emploi

Huskie Tools

Huskie Tools PRO LINE REC-MK7105YC Manuel utilisateur

Huskie Tools

Huskie Tools SP-20 Mode d’emploi

Huskie Tools

Huskie Tools REC-534YC Mode d’emploi

Huskie Tools

Huskie Tools REC-SB640 Manuel utilisateur

Huskie Tools

Huskie Tools SL-MKS720 Manuel utilisateur

Manuels Coupeur populaires d'autres marques

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuel utilisateur

Makita

Makita DCS552 Manuel utilisateur

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuel utilisateur

Makita

Makita 4112HS Manuel utilisateur

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuel utilisateur

Hitachi

Hitachi CM 4SB2 Guide de dépannage

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuel utilisateur

GCC Technologies

GCC Technologies AFJ-24S Manuel utilisateur

DeWalt

DeWalt XR LI-ION DCS350N Manuel utilisateur

Baudat

Baudat ES1 Manuel utilisateur

Mafell

Mafell ZAF 200 Mode d’emploi

Makita

Makita 4100NH Manuel utilisateur

Formax

Formax FD 574 Manuel utilisateur

EINHELL

EINHELL TE-MA 1500 Manuel utilisateur

Husqvarna

Husqvarna Cut-n-Break K 760 Manuel utilisateur

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuel utilisateur

TRI tool

TRI tool 301A Manuel utilisateur

Roller

Roller King 1 1/4 Manuel utilisateur