Huskie Tools S-32CC Mode d’emploi

Operating Instruction Manual

For S-32CC Hydraulic Cutters

With Parts List

HUSKIE TOOLS, INC.

http://www.huskietools.com [email protected]1

http://www.huskietools.com [email protected]2

GENERAL INFORMATION GUIDE FOR S-32CC CUTTER

The following steps are guidelines for safe operation of the Huskie cutters. Please take the time to review

them as these are helpful hints that have been accumulated over the years.

1. Stay within the maximum cutting limits of each tool as listed on page 5.

2. Try to keep the cutter head clean. When cleaning, use a spray lubricant to avoid a build up of dirt and

sand which will damage the cutter head.

3. Stop pumping when the blade reaches the extreme end of its advance. If the material being cut seems to

be cut but does not break free of the tool, this indicates that the blade is jammed on a small piece of

cable. Refer to “troubleshooting” on page three to free the blade.

4. All Huskie tools require proper care. Occasional cleaning and degreasing in solvent, and sharpening

blade and cutter head, will keep these tools operating without problems.

5. The most common problem encountered is blade breakage. Ninety-nine percent of all breakage occurs

because the cutter head is not securely latched before cutting. If the latch is not secured, the blade will

push open the cutter head and damage both the body head and blade. This causes the outside ear of the

blade to break on an angle. In some cases the whole cutter head may crack in half. Cutting material that

is not specified may also cause blade damage. In time these blades will fatigue and crack and must then

be replaced.

6. There may be a residue of oil present on new tools when they are removed from the original shipping

container. This is to protect the tool from corrosion during shipment and storage, and should not be

considered defective. The tool can be cleaned with a spray degreaser or soapy water.

7. If tool is jammed, avoid beating directly on the tool with a hammer, especially avoid flattening the piston

cylinder. Use a hammer in conjunction with a block of wood or soft material to free the blade.

8. All tools can be reconditioned and overhauled. Call factory and obtain an RGA # for returning tools.

http://www.huskietools.com [email protected]3

9. If the cutters are used under water, wash them down and lubricate after each use. This whole operation takes

less than five minutes. It may be helpful to paint new tools with a light color, corrosion resistant paint.

10. Always return tools to their carrying bag to protect them from sand and dirt. Extra bags can be purchased.

11. Always carry a spare blade, preferably attached to the carrying bag.

12. Use clear hydraulic fluid MV-32 available from your dealer or HTI.

13. When cutting, keep area clear of spectators as hardened metals may fly apart when severed.

14. Always cut the material at a 90 degree angle to the blade. Any other angle may cause the blade and head

shear to fracture. See illustration below.

GENERAL INFORMATION GUIDE FOR S-32CC CUTTER

http://www.huskietools.com [email protected]4

TROUBLESHOOTING GUIDE

1. Problem: Small wire strands or pieces of cable or debris get jammed between the cutter head and blade,

not allowing the blade to retract.

Solution: A) Hold release lever down while tapping on the ram with a block of wood and a hammer. If

this does not work or tool continues to hang up, proceed to step “B”.

B) Remove blade screw and release the ram. Then disassemble cutter head and remove burrs from both

blade and head shear, using a flat grinding stone on the rolled edge. Do not sharpen like a knife – leave

cutting edge flat! See illustration on page 2.

2. Problem: Blade is advanced under pressure with no load and the release lever seems to be stuck.

Solution: A) Use both hands to depress lever using body weight and the ground or other strong surface

for support. If this does not work, proceed to step “B”.

B) Lay tool flat on the ground or other strong surface and hit release lever with a block of wood and a

hammer to release pressure.

3. Problem: Tool will not advance when handle is pumped.

Solution: A) Remove body handle and check oil reservoir for proper fluid level. The oil should be to the

top of the reservoir when the cap is removed. Be sure the tool is fully retracted before removing cap.

B) After storing for a long period of time, or occasionally when the tool is new, a check ball may be

stuck not allowing it to advance. Invert the tool and rap the cutter head sharply on the ground. Do this

several times, then pump handle to advance the blade.

http://www.huskietools.com [email protected]5

OPERATING INSTRUCTIONS FOR ALL “S”

SERIES HYDRAULIC CUTTERS

1. Before cutting, make sure the material being cut is within the proper cutting capacity of the tool being used.

2. Open cutter head by lifting latch or removing lock pin, depending on the model being used.

3. Insert material between cutter head and blade and secure latch. It is important that you check the latch for

proper engagement before continuing with the cut. Failure to secure the latch can result in severe tool

damage and personal injury.

4. Align the material at a 90 degree angle to the blade. This will ensure a proper cut with minimal distor-

tion. If the material is cut at any other angle, severe blade damage may occur. Refer to diagram on page

two for proper alignment.

5. Proceed by pumping handle to advance blade. Once blade has made contact with the material, check

alignment once again for proper angle. Continue to pump handle and cut material.

6. Once the cut is made, the release lever on the side of the tool body can be depressed to retract the blade.

On the model S-85 cutter, the pump handle must be rotated 90 degrees clockwise and then closed to

depress release pin located under the handle.

7. These cutters do not have a by-pass cartridge like our compression tools, so they should be released once

the cut is made and not continued to be advanced. If the tool is advanced under pressure with no load, it

is difficult to release the blade. Refer to the troubleshooting on page three if this condition occurs.

8. Always wear eye protection and any other specified safety equipment when cutting. Be sure surrounding

area is clear, as hardened metals may fly apart when severed.

9. For EHS guy wire or bridge strand, use models S-24CC or S-32CC only! The use of any other S-series

cutter will result in severe blade damage and may cause personal injury.

10. Model S-85 cutter is designed for use on non-ferrous metals only! Do not cut steel or severe tool damage

and personal injury may occur.

http://www.huskietools.com [email protected]6

S SERIES SPECIFICATIONS

MODEL:

OUTPUT:

WEIGHT:

LENGTH:

S-16

4.4 ton

6 lbs.

15”L

S-20

4.4 ton

6 lbs.

15”L

S-24

7.8 ton

9 lbs.

17”L

S-32

19.8 ton

21 lbs.

27”L

S-40B

6.3 ton

12 lbs.

23”L

S-55

13.0 ton

17 lbs.

24”L

S-85

2.7 ton

15 lbs.

26”L

S-24CC

7.8 tpm

9 lbs.

17”L

S-32CC

19.8 ton

23 lbs.

27”L

Wire Ropes 16mm

5/8”

20mm

3/4”

22mm

7/8”

32mm

1-1/4”

20mm

3/4”

26mm

1”

Do not cut Do not cut Do not cut

Soft Steel Bolts 16mm

5/8”

17mm

11/16”

22mm

7/8”

32mm

1-1/4”

20mm

3/4”

32mm

1-1/4”

Do not cut 16mm

5/8

16mm

5/8”

Rebar, ground, &

anchor rod

13mm

1/2”

16mm

5/8”

16mm

5/8”

22mm

7/8”

16mm

5/8”

20mm

3/4”

Do not cut 16mm

5/8

16mm

5/8”

CU & AL wire 16mm

5/8”

20mm

3/4”

22mm

7/8

32mm

1-1/4”

40mm

1-1/2”

50mm

2”

45mm

3”

ACSR

(see page 65)

16mm

5/8”

20mm

3/4”

22mm

7/8

32mm

1-1/4”

40mm

1-1/2”

50mm

2” (1590)

Do not cut

Standard Guy Wire 13mm

1/2”

14mm

1/2”

16mm

5/8”

22mm

7/8”

16mm

7/8”

20mm

3/4”

Do not cut 14mm

9/16”

22mm

7/8”

Telephone & lead

sheathed cable

Do not cut Do not cut Do not cut Do not cut Do not cut Do not cut 85mm

3.35”

Do not cut Do not cut

http://www.huskietools.com [email protected]6

MODEL S-32CC PARTS DIAGRAM

MODEL S-32CC PARTS LIST

1 CE-12.7 Snap Ring 26-04 4 49 M4 X 5 Screw (C.P.) 55A-24 1

2 Pin (31) 26-03 2 50 Body Handle 26-39 1

3 Latch 32C-01 1 51 Body Handle Grip 26-40 1

4 M8 X 35 Screw 32C-02 1

5 M8 Lock Washer 40-25 1

6 4 X 36 Drive Pin 26-02 1

7 Spring Holder 26-06 1

8 Spring (81) 26-07 1

9 Head 32CE-02 1

10 Anvil Blade 32C-04 1

11 M5 X 10 Screw (D.P.) 55A-11 1

12 Cylinder Head 32CE-01 1

13 Cutter Blade 32C-06 1

14 Spring (192) 32C-07 1

15 Ram 32C-08 1

16 Blade Screw 32-09 1

17 P-45 Back-Up Ring (B.C.) 32-10 1

18 P-45 O-Ring 32-11 1

19 Exhaust Valve Screw 26-19 1

20 Copper Gasket (4) 26-20 1

21 Spring (68) 26-21 1

22 1/4” Ball 26-22 1

23 Spring (4) 16-48 1

24 3/16” Ball 16-49 2

25 M6 X 15 Screw (F.P.) 32-23 1

26 2.5 X 20 Drive Pin 32-13 1

27 Release Knob Label 32-14 1

28 Release Knob 32-15 1

29 Release Valve Stem 32-16 1

30 P-3 O-Ring 16-36 1

31 7/32” Ball 16-26 1

32 Spring (76) 16-39 1

33 9/32” Ball 16-40 1

34 M10 X 10 Screw (F.P.) 16-41 1

35 PS-9 Pent Seal 32-18 1

36 P-9 Back-Up Ring (B.C.) 32A-01 1

37 VC-9 Oil Seal 32A-02 1

38 Pump Piston 32-21 1

39 CE-7 Snap Ring 40-49 4

40 Pin (5) 26-29 2

41 Pump Handle 26-30 1

42 Pump Handle Grip 26-31 1

43 Body 32A-04 1

44 Suction Tube 26-34 1

45 Filter Base Ass'y 26-35 1

46 P-38 O-Ring 26-37 1

47 Oil Reservoir (10) 32A-03 1

48 Reservoir Cap 410-55 1

CODE

NO.

DESCRIPTION

QTY.

NO.

DESCRIPTION

QTY.

CODE

http://www.huskietools.com [email protected]7

All Huskie REC-Series battery driven products carry a 5 year warranty, and the ECO-Series

carry a 3 year warranty. The BP-70E, BP-70EI, and the BP-70MH batteries carry a 5 year

warranty from the date stamped on the battery. The LED indicator on the BP-70-EI battery

carries a 1 year warranty from purchase date. Hydraulic hammers carry a one year warranty

and all other Huskie products carry a 5 year warranty. Huskie reserves the right to determine

all warranty claims. Failure due to misuse, abuse or repairs attempted by anyone other than

Huskie Tools, Inc., or an authorized service center render this warranty null and void. Our

patented drop-out bypass cartridge can be re-calibrated or tested at no charge for the life

of the tool. All factory repaired or reconditioned hydraulic tools carry a one year warranty

on parts and labor.

REPAIR AND WARRANTY CLAIMS

All claims must be sent to Huskie for inspection and authorization. A Return Goods

Authorization is required before shipping tools to Huskie. Secure the authorization by

telephoning 1-800-860-6170 or writing to Huskie's main office with details of claim. Non-

warranty repairs are handled using the same procedure. Repairs exceeding 50% of the cost

of a new tool will be advised before repairs are made.

PLEASE RETAIN FOR YOUR RECORDS

Purchaser’s Name _____________________________________________________

Address _____________________________________________________

City, State, Zip _____________________________________________________

Tool Model Number _____________________________________________________

Serial Number _____________________________________________________

Date Purchased From _____________________________________________________

Purchased From _____________________________________________________

MODEL S-32CC WARRANTY

Autres manuels Huskie Tools Coupeur

Huskie Tools

Huskie Tools ECO-336 Manuel utilisateur

Huskie Tools

Huskie Tools SP-20 Mode d’emploi

Huskie Tools

Huskie Tools ECO-MK7500 Manuel utilisateur

Huskie Tools

Huskie Tools ECO-336B Manuel utilisateur

Huskie Tools

Huskie Tools REC-534YC Mode d’emploi

Huskie Tools

Huskie Tools REC-434YC Mode d’emploi

Huskie Tools

Huskie Tools S-20 Mode d’emploi

Huskie Tools

Huskie Tools REC-Y33 Mode d’emploi

Huskie Tools

Huskie Tools REC-685YC Manuel utilisateur

Huskie Tools

Huskie Tools REC-SB640 Manuel utilisateur

Huskie Tools

Huskie Tools 7M PRO LINE Series Manuel utilisateur

Huskie Tools

Huskie Tools SL-MKS720 Manuel utilisateur

Huskie Tools

Huskie Tools SP-85 Mode d’emploi

Huskie Tools

Huskie Tools REC-660YC Manuel utilisateur

Huskie Tools

Huskie Tools ECO-336A Manuel utilisateur

Huskie Tools

Huskie Tools REC-MKS740L Manuel utilisateur

Huskie Tools

Huskie Tools S-16 Mode d’emploi

Huskie Tools

Huskie Tools REC Series Manuel utilisateur

Huskie Tools

Huskie Tools S-55B Mode d’emploi

Huskie Tools

Huskie Tools SP-40 Mode d’emploi

Huskie Tools

Huskie Tools REC-S624H Manuel utilisateur

Huskie Tools

Huskie Tools PRO LINE REC-MK7105YC Manuel utilisateur

Huskie Tools

Huskie Tools REC-5OU Mode d’emploi

Huskie Tools

Huskie Tools REC-5OM Mode d’emploi

Manuels Coupeur populaires d'autres marques

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuel utilisateur

Makita

Makita DCS552 Manuel utilisateur

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuel utilisateur

Makita

Makita 4112HS Manuel utilisateur

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuel utilisateur

Hitachi

Hitachi CM 4SB2 Guide de dépannage

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuel utilisateur

GCC Technologies

GCC Technologies AFJ-24S Manuel utilisateur

DeWalt

DeWalt XR LI-ION DCS350N Manuel utilisateur

Baudat

Baudat ES1 Manuel utilisateur

Mafell

Mafell ZAF 200 Mode d’emploi

Makita

Makita 4100NH Manuel utilisateur

Formax

Formax FD 574 Manuel utilisateur

EINHELL

EINHELL TE-MA 1500 Manuel utilisateur

Husqvarna

Husqvarna Cut-n-Break K 760 Manuel utilisateur

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuel utilisateur

TRI tool

TRI tool 301A Manuel utilisateur

Roller

Roller King 1 1/4 Manuel utilisateur