Hunter PRO-C P2C Series Mode d'emploi

PRO-C®

RESIDENTIAL AND LIGHT COMMERCIAL

IRRIGATION CONTROLLER

P2C Series

Modular Controller

Indoor/Outdoor

Owner's Manual

Installation Instructions

PRO-C

MO TU WE TH FR SA SU ODD EVEN INTERVAL

BYPASS

STATION

PUMP

DELAY

DAYS LEFT

SEC

HH:MM

CYCLE

SOAK

PRG

1-800-733-2823

Need more helpful information on your product?

Find tips on installation, controller programming, and more.

hunter.help/P2C

SCAN

for help

hunter.help/P2C

Table of Contents

3Specications

4Pro-C Controlller Components

6Mounting the Controller to a Wall

7Connecting AC Power

8Installing Station Modules

9Connecting Station Wires

10 Connecting a Master Valve

11 Connecting a Pump Start Relay (optional)

12 Connecting a Hunter Clik Weather Sensor (not included)

14 Connecting a Hunter Remote (not included)

15 Connecting to a Hunter Solar Sync® Sensor

16 Setting the Current Date and Time

17 Setting Program Start Times

18 Setting Station Run Times

19 Setting a Watering Schedule

21 Options for Running Your Irrigation System

24 Hidden and Advanced Features

25 Troubleshooting Guide

26 FCC Notice

Built on Innovation®

Operating Specications

• Station Count: Conventional wiring from 4 to 23 stations,

two-wire EZ Decoder System option up to 32 stations

• Station Run Time: 1 minute to 6 hours (optional Seconds

Mode, see pg. 18)

• Start Times: 4 individual starts per program, three

programs available (A, B, C)

• Watering Schedule: 7-day calendar, interval watering up

to a 31-day interval or true odd or even day programming

Electrical Specications

• Transformer Input: 120 VAC, 60 Hz (230 VAC, 50/60 Hz

for international use)

• Transformer Output: 24 VAC, 1 A

• Station Output: 24 VAC, 0.56 A per station

• P/MV Output: 24 VAC, 0.28 A

• Maximum Output: 24 VAC, 0.84 A (includes Master

Valve Circuit)

• Battery: 9 V alkaline battery (not included) used only for

non-AC programming of the control panel

• Battery, front panel, internal CR2032 lithium for real-

time clock

Specications

Cabinet Dimensions

• Height: 9" (23 cm)

Width: 10" (21.5 cm)

Depth: 4⁄" (10.9 cm)

• Cabinet is NEMA 3R, IP44 rated

Default Settings

All stations are set to zero run time. This controller has a

non-volatile memory that retains all entered program data,

even during power outages, without need for a battery.

4hunter.help/P2C

Pro-C Controlller Components

PRO-C

MO TU WE TH FR SA SU ODD EVEN INTERVAL

BYPASS

STATION

PUMP

DELAY

DAYS LEFT

SEC

HH:MM

CYCLE

SOAK

PRG













PRO-C

MO TU WE TH FR SA SU ODD EVEN INTERVAL

BYPASS

STATION

PUMP

DELAY

DAYS LEFT

SEC

HH:MM

CYCLE

SOAK

PRG





















AControl Dial

Run Normal dial position for automatic

operation

Set Date/Time Set current date and time

Set Program Start

Times

Set 1 to 4 start times in each program

Set Station Run

Times

Set run time for each station

Set Days to Water Select individual days to water, odd,

even, or interval watering schedule

Set P/MV

Operation

Enable or disable the Pump or Master

Valve for each station

Seasonal

Adjustment

Apply global adjustments to station run

times based on seasonality (5% to 300%)

Solar Sync

Sensor

Allows user to program settings when

using Solar Sync ET Sensor

Manual — Single

Station

Activates one-time watering of a

single station

BWiring Compartment

9 V Battery An alkaline battery (not included) allows

programming of the controller facepack

without AC power

Reset Button Resets the controller, keeping all

programmed data intact

SmartPort Input

Terminals

Used to connect a SmartPort Wiring

Harness, which enables Hunter remote

controls

Transformer Internal 24 VAC transformer, prewired

with power cord and plug

Junction Box Wiring compartment that provides an area

for connecting primary AC power to the

controller

Common Terminal Used for eld Common connections to

solenoid valves; also used to complete

sensor circuit wiring

Sensor

Inputs (x 2)

Used to connect Hunter Solar Sync and

Clik Sensors

Power Slide Slide power lock On and O when inserting

and removing PCM output modules

Built on Innovation®

Pro-C Controller Components

Outdoor model is water- and weather-resistant.

Connecting the outdoor Pro-C Controller to the

primary power should be done by a licensed

electrician following all local codes. Improper

installation could result in shock or re hazard. This

device is not intended for use by young children.

Never let children play with this device.

Note

hunter.help/P2C

Mounting the Controller to a Wall

All necessary hardware is included for indoor and

outdoor installations.

1. Use the hole at the top of the controller as a reference

and secure a 1" (25 mm) screw into the wall. Note: Install

screw anchors if attaching to drywall or masonry wall.

2. Align controller with the screw and slide the keyhole

on top of the controller over the screw.

3. Secure controller in place by installing screws in the

holes.

Always use UL Listed ½" (13 mm) conduit with male

adapter when installing AC wiring. Pro-C Controllers

are intended to be supplied AC power with a 15 A

rated overcurrent protected device.

To be performed by a licensed electrician only.

 V  V

U.S. International

Outdoor Cabinet

 GROUND

(Green)

 NEUTRAL

(White)

 HOT

(Black)

Built on Innovation®

Outdoor Cabinet

P2C models are prewired with a power cord and plug for

simple installations in both indoor and outdoor applications.

If the controller is to be powered by direct line voltage,

follow these wiring instructions:

1. Route AC power cable and conduit through the

½" (13 mm) conduit opening on the le side of the

cabinet bottom.

2. Connect the wires to the transformer wires located inside

the junction box. Always use a UL Listed conduit ½"

(13 mm) male adapter when installing the AC wiring.

3. Insert the adapter into the ½" (13 mm) hole at the bottom

of the controller. Attach a nut to the adapter inside the

enclosure.

Connecting AC Power

8hunter.help/P2C

Installing Station Modules

The Pro-C Controller is supplied with a factory-installed

base module for up to 4 stations. Additional modules may

be added in increments of 3 stations (PCM-300),

9 stations (PCM-900), or 16 stations (PCM-1600). In total,

a conventionally wired system can be expanded up to

23 stations. Additional modules are sold separately.

The Pro-C Controller is also compatible with the EZ Decoder

System (EZDS) for hybrid conventional and two-wire

operations. Add a Pro-C Decoder Module (PC-DM) to enable

control for up to 32 total stations. This system uses the same

EZ-1 Decoders used with ICC2, HCC, and HPC Controllers.

For more installation and programming details, please refer

to the PC-DM Installation Guide.

Installing PCM Modules

The Pro-C Controller is designed with a simple-to-use

Power Lock feature that ensures the modules are energized

and rmly secured into the controller. The Power Lock

can unlock or lock all modules at the same time by simply

pushing the Power Lock slide.

1. Slide the Power Lock into the Power O (unlocked)

position. Insert the PCM modules into the appropriate

sequential position in the controller cabinet.

2. Once all of the modules are in place, slide the

Power Lock into the Power On (locked) position to

energize and secure the modules into the controller.

3. The Pro-C Controller will automatically recognize the

correct number of stations. It is not necessary to press

the reset button on the back of the facepack or cycle

power to the controller.

Built on Innovation®

1. Route valve wires between control valve location

and controller.

2. At valves, attach a Common wire to either solenoid wire

of all valves. This is most commonly a white wire. Attach

a separate control wire to the remaining wire of each

valve. All wire splice connections should be done using

waterproof connectors.

3. Route valve wires through the conduit and attach the

conduit to one of the openings on the cabinet bottom.

4. Strip ½" (13 mm) of insulation from ends of all wires.

Secure the valve Common wire to COM (Common)

terminal. Attach all individual valve control wires to the

appropriate station terminals.

Connecting Station Wires

COM

Master Valve

COM

P/MV

hunter.help/P2C

Connecting a Master Valve

Connect either wire from the Master Valve

to the P/MV terminal on the 4-station base

module. Connect remaining wire to the

COM (Common) terminal.

Table des matières

Autres manuels Hunter Contrôleurs

Hunter

Hunter EC Manuel utilisateur

Hunter

Hunter ICC-800PL Mode d'emploi

Hunter

Hunter Pro-C Mode d'emploi

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter XC Hybrid Mode d'emploi

Hunter

Hunter i-core IC-600PL Manuel utilisateur

Hunter

Hunter ACC Manuel utilisateur

Hunter

Hunter ICC2 Manuel d'installation

Hunter

Hunter SRC Plus Manuel utilisateur

Hunter

Hunter ACC2 Manuel d'installation

Hunter

Hunter ACC2 Manuel d'installation

Hunter

Hunter SRC Plus Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter XC HYBRID Series Mode d’emploi

Hunter

Hunter NODE-BT Manuel utilisateur

Hunter

Hunter X-CORE XC-2 Mode d'emploi

Hunter

Hunter Pro-HC601-A Manuel utilisateur

Hunter

Hunter SVC Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter Pro-C Mode d'emploi

Hunter

Hunter Hydrawise HCC-800-PL Manuel utilisateur

Hunter

Hunter X-CORE Manuel utilisateur

Hunter

Hunter Pro-C Manuel utilisateur

Hunter

Hunter Hydrawise Pro-HC Guide de démarrage rapide

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur