HUANUO HNPS01 Manuel utilisateur

Model:HNPS01

3 TIERS PRINTER RACK

INSTRUCTION MANUAL 2

Thank you for choosing this HUANUO product! At HUANUO

we strive to provide you with the best quality products and

services in the industry. Please share your experience of our

product with others at www.huanuoav.com/reviews if you

are satisﬁed. Should you have any issues, please don't

hesitate to contact us.

Technical Support:

1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)

Other Info:

[email protected] (US/CA)

Website:

www.huanuoav.com

Supplied Parts

A X2 B X1 C X4 D X16 E X4

Wire Shelf Wooden Board Pole Plastic Clip Nylon Caster

Wrench

Screw Nylon Casters [E] into the bottom of four Poles [C] by wrench.

Snap one pair of Plastic Clips [D] on the same groove of each pole as

shown in the below image. The arrow of all plastic clips should be

pointed up, and the grooves of pole should be covered by convex part of

plastic clips.

Grooves of Pole Convex Part of

Plastic Clips

Step 1

D

C

E

Step 3

Step 2

Keep the collar of the Wire Shelf [A] downward. Then slide the Wire Shelf

[A] into the plastic clips from the top of each poles.

Keep the collar downward

Set the shelf upright. Refer to Step 1, 2 to snap the plastic clips [D] on

the same grooves of each poles at your desired position for the second

wire shelf [A]. Then refer to Step 2 to assemble the second wire shelf [A].

DA

C

A

C

D

Step 4

Insert the plastic parts under the Wooden Board [B] into the top of the

four poles to make it snug on the poles. Push ﬁrmly down the corners

of the two wire shelves [A] by rubber mallet (not included) to make the

wire shelf [A] secure onto the plastic clips. Now the three tiers printer

rack is completely assembled.

NOTE: Put fabric between rubber mallet and shelf to prevent damage.

B

C

Mallet

Table des matières

Autres manuels HUANUO Support et étagère

HUANUO

HUANUO HNCM18 Manuel utilisateur

HUANUO

HUANUO HNWSS1 Manuel utilisateur

HUANUO

HUANUO HNCM2 Manuel utilisateur

HUANUO

HUANUO HNWSS1 Manuel utilisateur

HUANUO

HUANUO HNDA1 Manuel utilisateur

HUANUO

HUANUO HNPS02 Manuel utilisateur

HUANUO

HUANUO HNSSD6 Manuel utilisateur

HUANUO

HUANUO HNCM9 Manuel utilisateur

HUANUO

HUANUO HNFO2 Manuel utilisateur

HUANUO

HUANUO HNCM4 Manuel utilisateur

HUANUO

HUANUO HNDS11 Manuel utilisateur

HUANUO

HUANUO HNCM12-1 Manuel utilisateur

HUANUO

HUANUO HNCM16 Manuel utilisateur

HUANUO

HUANUO HNTT Manuel utilisateur

HUANUO

HUANUO HNKB03 Manuel utilisateur

HUANUO

HUANUO HNWSS4 Manuel utilisateur

HUANUO

HUANUO HNCM1 Manuel utilisateur

HUANUO

HUANUO HNCM1 Manuel utilisateur

HUANUO

HUANUO HNHM4 Manuel utilisateur

HUANUO

HUANUO HNDS8 Manuel utilisateur

HUANUO

HUANUO HNCPB Manuel utilisateur

HUANUO

HUANUO HNQF2 Manuel utilisateur

HUANUO

HUANUO HNLA6 Manuel utilisateur

HUANUO

HUANUO HNCM7 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur