HS-Technik TorqBee TBASL-5-2 Manuel utilisateur
OPERATING INSTRUCTIONS
TorqBee®
- Original operang instrucons -
Issue date: February 2021
Tool Firmware: from 2.6.0.8
HST-Tool-Manager: from 2.0.6.0
NOTE
In case of doubt, the original German version
of the operang instrucons applies.
- 2 -
PAGE
4
PAGE
PAGE
PAGE
1.1 Scope of delivery 4
1.2 General informaon 4
1.3 Signs and symbols used 5
1.4 Structure of the warnings 6
1.5 Technical terms and abbreviaons used 6
1.6 Intended use 7
1.7 Improper use 7
1.8 Dues of the operator 8
1.9 Dues of personnel 8
1.10 Training of personnel 8
1.11 Guarantee and liability 9
1.12 Copyright 10
2.1 Occupaonal safety 11
2.2 Electrical safety 12
2.3 Safety of people 12
2.4 Use and handling of power tools 13
2.5 Use and handling of baery tools 14
2.6 Service 15
3.1 Handling the associated lithium ion baery 16
3.2 Informaon on the associated charger 17
3.3 Structural modicaons 17
3.4 Cleaning the device and disposal 18
4.1 Tool structure 20
4.2 Operaon 21
4.2.1 Inserng and removing the baery 21
4.2.2 Press start buon 22
4.2.3 Front LED 22
4.2.4 LED status and sound signals 23
4.2.5 Overload 23
4.2.6 Shut-down mode 24
4.2.7 Clockwise / Counterclockwise rotaon switch 25
4.2.8 Setting the tightening torque 26
4.3 Maintenance and service 27
4.4 Cleaning 27
4.4.1 General informaon 27
- 3 -
PAGE
28
PAGE
PAGE
PAGE
- 4 -
Dear customers,
thank you for choosing a HS-Technik GmbH product.
This quality product „Made in Germany“ fulfils the highest requirements with regard to
performance, quality and accuracy. When used correctly the product will undoubtedly
perform very well for many years.
These operating instructions contain information on safety and for the operation of the
tool. In addition it contains information on the dimensions and technical data. We would
be happy to assist you with additional information or to answer your questions. Our
technical support and our technicians would be happy to assist you.
• Baery ghtening tool
• USB Cable (Type A on Mini B)
• Operang instrucons
Read the operang instrucons before inial operaon.
This operang instrucon should make it easier for the operator to get to know the tool
and to use it for its intended purpose. The operang instrucons include important
informaon related to the safe and proper operaon of the tool. Compliance with these
instrucons helps you to:
• Avoid hazards
• Avoid repair costs and downmes
• Increase the reliability and the lifespan of the product.
- 5 -
This operang instrucons must be read and applied by every person who is assigned to
conduct work using this tool.
In addion to these operang instrucons the applicable regulaons on accident
prevenon and environmental protecon should be observed.
NOTE
Aer reading, keep the operang instrucons in a place accessible to every
operator. If you have any further quesons, please feel free to contact us.
The following signs and symbols will be used in this operating instructions or on the
product:
Read this operang instrucons
do not dispose with household waste
Do not dispose the baery in a re
Do not throw the baery into water
EU conformity marking
®Registered trademark
- 6 -
The warnings are structured as follows:
DANGER
Indicates an immediate dangerous situaon that can lead to serious or even
deadly injuries and/or that could seriously damage or even destroy the tool.
WARNING
Indicates a potenally dangerous situaon that can lead to serious injuries
and/or damage to the tool.
NOTE
Important and useful informaon on using this tool.
°C Degrees Celsius, temperature
AC Alternate current
Ah Amp hours, electric charge, baery capacity
ahv Overall vibraon
dB(A) Decibels, sound pressure level (A-weighted)
DC Direct current
Hz Hertz, Frequency
Li-Ion Lithium-ion, baery technology
LpA Emission sound pressure level, workplace-related
m/s² Acceleraon, Vibraon
- 7 -
min-1 Revoluons per minute, Speed
mNN Meters above sea level, height
SN Serial number
V Volts, electrical voltage
W Was, electrical power
Nm Newton meters, torque
This baery tool was designed to prepare screw connecons.
The tool may only be used for this purpose as described in this operang instrucons. Only
materials that are suitable for this type of tool may be used.
WARNING
Intended use also includes
• following all indicaons of the operang instrucons and
• observance of inspecon and maintenance works.
Any other use or use beyond that is considered improper use. HS-Technik GmbH is not
liable for any damage resulng from this.
DANGER
The use of this tool for other purposes, e.g. for hammering, is not permied.
Improper use or incorrect accessories can lead to dangers with unforeseeable
consequences.
We accept no liability for damage and malfunctions resulting from non-observance of
these operating instructions and improper use.
- 8 -
The operator undertakes to only allow people who are familiar with the basic regulaons
on work safety and accident prevenon and who have been trained on how to use the tool
at the workplace and to work with this tool.
The safety awareness of the personnel while working has to be reviewed at regular inter-
vals.
In addion it is necessary to dene safety measures for operator protecon which are
based upon an esmaon of the vibraon load during actual condions of use.
Prior to its use all people who work with this tool are obligated to inform themselves of
the applicable workplace safety and accident prevenon regulaons for this power tool
and to observe them.
It is recommended that every operator wears hearing protecon.
Only trained and instructed personnel should work with this tool. The responsibilies of
the personnel must be clearly dened. Trainees may only work with this power tool under
the supervision of an experienced person.
- 9 -
Guarantee and liability claims for personal injury and property damage are excluded, if
caused by one or more of the following:
• improper use
• failure to observe these operang instrucons
• improper installaon, commissioning, operaon and maintenance of the device
• Operang the device with defecve safety devices or improperly installed or non-func-
oning safety and protecve devices
• Failure to observe the informaon in the operang instrucons regarding transport,
storage, assembly, commissioning, operaon and maintenance of the device
• unauthorised structural modicaons to the device
• improperly performed repairs
• catastrophes due to external inuences and acts of God
- 10 -
These operating instructions are intended solely for the operator and its personnel.
They contain guidelines and information which may not be fully or partially
• reproduced
• distributed or
• otherwise shared.
The copyright of these operating instructions is retained by HS-Technik GmbH.
Manufacturer’s address:
Im Martelacker 12
D-79588 Efringen-Kirchen
Telephone: +49 (0)7628 - 91 11-0
Fax: +49 (0)7628 - 91 11-90
E-mail: [email protected]
Internet: www.hs-technik.com
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels HS-Technik Outils électriques
