HPE 1410-16G Manuel utilisateur
HPE 1410-16G Switch Quick Setup Guide
For more detailed information to set up your switch, view or download the Installation and Getting Started
Guide for your switch at:
http://www.hpe.com/networking/support
1. Unpack and check included parts. •Switch
•Accessory kit (installation hardware)
•AC power adapter (and power cord, if applicable)
•Documentation kit
2. Prepare for installation. To avoid personal injury or product damage, review the “Safety Precautions” (page 3).
3. Connect power and verify that the Switch Power LED turns on. The switch does not contain a power switch. It is turned
on by connecting power through the AC power adapter supplied with your switch
©Copyright 2011, 2016 Hewlett Packard Enterprise Development LP
The information in this document is subject to change without notice.
Part Number: 5998-1369R
Published: January 2016
4. Install the Switch Hardware. Turn off the switch before installing the switch hardware.
Table or desktop: Attach the four self-adhesive pads (included
in the accessory kit) to the bottom corners of the switch.
Wall or Under-Table: A special kit for wall-mounting (or
under-table mounting) is included. Use a #1 Phillips
(cross-head) screwdriver and the 20-mm M4 tap screws
(included).
For screw positions, see the <mounting template on page 4.>
(Under-Table: After installation, a third screw may be used to
prevent switch movement.)
For wall-mounting, the network ports may face up or down. Do
not mount the switch with ventilation ducts facing up or down.
(See “Safety Precautions” (page 3).)
Rack Mounting: A special rack-mounting kit is included. Use a #1 Phillips (cross-head) screwdriver to attach the special
brackets to the switch using the eight 8-mm M4 screws. Then use the four number 12-24 screws to secure the brackets to the
rack.
5. (Optional) Lock the Switch. Use a Kensington lock or
similar device (not included) to physically secure the switch.
6. Power on the Switch. Use the cable tie strap to secure the
connection.
7. Connect network cables.
Safety Precautions
To avoid personal injury or product damage when installing your switch, read the installation precautions
and guidelines below.
Installation Precautions
WARNING!
•The rack or cabinet should be adequately secured to prevent it from becoming unstable, tilting
or falling.
Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest
devices at the bottom and progressively lighter devices above.
•Do not wall-mount any switch without checking for restrictions in the Installation and Getting
Started Guide.
Wall-mount the switch with network ports facing up or down (away from or toward the floor).
Do not wall-mount the switch with the ventilation or fan ducts facing up or down.
CAUTION:
•Ensure the power source circuits are properly grounded, then use the power cord supplied with
the switch to connect to the AC power source.
•If your installation requires a different power cord than the one supplied with the switch and/or
power supply, be sure the cord is adequately sized for the switch’s current requirements. In
addition, be sure to use a power cord displaying the mark of the safety agency that defines the
regulations for power cords in your country/region. The mark is your assurance that the power
cord can be used safely with the switch and power supply.
•When installing the switch, the AC outlet should be near the switch and should be easily
accessible in case the switch must be powered off.
•Ensure the switch does not overload the power circuits, wiring, and over-current protection. To
determine the possibility of overloading the supply circuits, add together the ampere ratings of
all devices installed on the same circuit as the switch and compare the total with the rating limit
for the circuit. The maximum ampere ratings are usually printed on the devices near the AC
power connectors.
•Do not install the switch in an environment where the operating ambient temperature exceeds
its specification.
•Ensure the air flow around the switch is not restricted. Leave at least 7.6 cm (3 inches) for
cooling. For the air flow direction, see the Installation and Getting Started Guide for your product,
located on the Hewlett Packard Enterprise Networking web site at:
http://www.hpe.com/networking/support
For additional Safety and Regulatory information, refer to the Safety and Regulatory documentation
included with your switch.
Wall Mounting Template for HPE 1410-16G Switch
Safety and Regulatory Information for HPE 1410-16G Switches
HPE 1410-16G Switch (J9560A)
For power, the switch requires a connection to an external power adapter. Use only the external
power adapter module supplied with this product. Power adapter module specifications are
provided below.
Electrical:
Wall plug-in power adapter module (HPE part
numbers are specified below):
Universal power adapter module (5188-6700):
•AC Input Voltage: 100-240 V
•AC Input Voltage: 100-240 V
•Maximum AC Input Current: 0.5 A
•Maximum AC Input Current: 0.4 A
•AC Input Frequency Range: 50/50 Hz
•AC Input Frequency Range: 50/50 Hz
•Power Consumption: 15 W
•Power Consumption: 13 W
•DC Output Voltage: 12 ± 10% V
•DC Output Voltage: 12 ± 10% V
•Maximum DC Output Current: 1.25 A
•Maximum DC Output Current: 1.2085 A
Environmental:
0°C to 45°C (32°F to 113°F)Operating Temperature:
HPE 1410-16G Switch (J9560A)
15% to 95% at 40°C (104°F) (non-condensing)Relative humidity:
-40°C to 70°C (-40°F to 158°F)Non-Operating Temperature:
15% to 90% at 65°C (149°F) (non-condensing)Non-Operating Relative
humidity:
3.0 km (10,000 ft)Maximum Operating Altitude:
4.6 km (15,000 ft)Maximum Non-Operating
Altitude:
Safety:
EN60950-1:2006+A11:2009+A1:2010+A12:2011 / IEC60950-1:2005; Am1:2009; CSA22.2 No.
60950-1-07 2nd; UL60950-1 2nd
Standards:
EN 60825-1:2007 / IEC 60825-1:2007 Class 1Lasers:
Class 1 Laser Products / Laser Klasse 1
HPE 1410-8G (J9559A), 1410-16G (J9560A), 1410-24G (J9561A) Switches:
External Power Adapter and Power Cords:
Power Cords for External AC/DC Power AdapterExternal AC/DC Power
Adapter
8120-6317South Africa8121-0870Australia/New Zealand5188-6700All countries/
regions
8121-0963Taiwan8121-0664Thailand
8120-8699United Kingdom/Hong
Kong/Singapore/
Malaysia
8120-8373China
8120-6313United States/Canada/
Mexico
8120-6314Continental Europe/Denmark/
Switzerland/Israel/Vietnam/
Indonesia
8121-1081Brazil8121-0702India
8120-8357Argentina8120-6316Japan
8121-0514Chile
Wall Plug-in External AC/DC Power Adapter (AC Power cords are not used)
5184-5863United States/Canada
5184-5864Continental Europe/Denmark/Norway/Sweden/Switzerland
Japan Power Cord Warning:
Russia/Belarus/Kazakhstan/CEE Safety:
European Community Declaration of Conformity
Regulatory information
For important safety, environmental, and regulatory information, see Safety and Compliance Information
for Server, Storage, Power, Networking, and Rack Products, available at http://www.hpe.com/support/
Safety-Compliance-EnterpriseProducts.
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us
improve the documentation, send any errors, suggestions, or comments to Documentation Feedback
edition, and publication date located on the front cover of the document. For online help content, include
the product name, product version, help edition, and publication date located on the legal notices page.
Table des matières
Autres manuels HPE Changer
HPE
HPE Aruba Instant On 1960 Instructions de montage
HPE
HPE OfficeConnect 1420 Series Manuel utilisateur
HPE
HPE 5820X Series Manuel utilisateur
HPE
HPE 5140 24G PoE+ 4SFP+ EI Sw Instructions de montage
HPE
HPE 12500 Series Manuel d'installation
HPE
HPE FlexFabric 12900 Manuel d'installation
HPE
HPE Aruba 6200F Instructions de montage
HPE
HPE 5800 Series Manuel utilisateur
HPE
HPE 5945 Instructions d'installation
HPE
HPE SN6000B Manuel d'utilisation et d'entretien
HPE
HPE FlexNetwork 7500 Series Manuel utilisateur
HPE
HPE FlexFabric 5940 SERIES Manuel d'installation
HPE
HPE FlexNetwork 5510 HI Series Manuel utilisateur
HPE
HPE Altoline 6940 32QSFP+ Instructions de montage
HPE
HPE FlexNetwork 7500 Series Manuel d'installation
HPE
HPE FlexNetwork 5130 EI Series Manuel utilisateur
HPE
HPE FlexNetwork 10500 SERIES Manuel utilisateur
HPE
HPE FlexFabric 5950 Series Manuel utilisateur
HPE
HPE Aruba Networking CX 6200 Series Manuel utilisateur
HPE
HPE 3100 v2 Series Manuel utilisateur
