HP 600R Series Manuel utilisateur

600R Series Remote Access Points | Installation Guide 1

600R Series Remote Access Points

Installation Guide

The 600R Series access points are dual-radio tri-band 802.11ax Wi-Fi 6E remote access points that provide

connectivity for both wired and wireless client devices.

Package Contents

The following materials are included with this product:

nAP-605R access point x 1

nAC-to-DCpower adapter (with power cord) x 1

n(For AP-605R bundle only) AP-605CM12 LTE CAT12 cellular module (pre-installed) x 1

To simplify the ordering, Aruba offers the AP-605Rbundle that combines an AP-605R access point, a power adapter

(with power cord) and a AP-605CM12 LTE CAT12 cellular module (pre-installed)

Hardware Overview

Figure 1 AP-605R Front View

1 System Status LED

2 LCD Panel

3 LCDButton

2| Rev 03|August 2023

Figure 2 AP-605R Bundle Front View

1 System Status LED

2 LCD Panel

3 LCDButton

The antennas of the LTEmodule are in a folded position when taken out of the package. To ensure the antennas

function well, put the antennas in a vertical position as shown in .

System Status LED

The system status LED is located on the top panel of the access point indicates the system status of the

access point.

Color/State Meaning

Off Access point powered off

Green - blinking 1Access point booting, not ready

Green - solid Access point ready, fully functional

Red System error condition or thermal shutdown engaged - Immediate atten-

tion required

Table 1: System Status LED

1. Blinking: one second on, one second off, 2 seconds cycle.

LED Display Settings

The LEDs have three operating modes that can be selected in the system management software:

nNormal mode: default after power on. Refer to Table 1.

nOff mode: the LED is off

nBlink mode: the LED blinks green

Pressing the reset button for less than 10 seconds during normal operation will toggle the LED mode

between “normal” (default after power on) and “off” mode.

Pressing the reset button for longer than 10 seconds may cause the accesspoint to reset and return to the factory

default state.

LCD Panel

The LCD panel is located on the front panel of the access point that displays the access point's bootup and

system status information.

The LCD button is located on the right side of the LCDpanel and used to operate the LCD panel:

nWhen booted up, the LCD will display the home page, which is Aruba logo by default, but it is

configurable by the system management software. Short pressing the LCD button will scroll through the

pages on the LCD screen. The LCD display will return to the home page after 10 seconds of inactivity.

nLong pressing the LCD button will adjust the LCD's backlight brightness.

Acess PointState LCDDisplays

During access pointboot (system status

LEDblinking green)

Display bootup status information, such as "APpowering

up...", "Connecting to network" and etc.

Access pointis up and running (system status

LED solid green)

Display logo (home page) and system status information.

Short pressing the LCD button on the right of the LCDscreen

will scroll through pages.

Access point is in error condition or thermal

shutdown mode (system status LEDsolid red)

Display relevant information about the error condition.

Table 2: LCD Panel Displays

Rev 03 | August 2023 | 3

4| Rev 03|August 2023

Figure 3 600R Series Rear and Side View

1 Reset Button

2 Micro-B Console Port

3 E0 Ethernet Port (Orange)

4 E1 Ethernet Port (Orange and Blue)

5E2 Ethernet Port (Blue)

6E3 Ethernet Port (Blue)

7E4 Ethernet Port (Red)

8 USB Interface

9 Kensington Lock Slot

Reset Button

The reset button can be used to reset the access point to factory default settings or turn off/on the LED

display.

Use one of the following methods to reset the access point to factory default settings:

nTo reset during normal operation:

lHold the reset button for more than 10 seconds while the access point is running.

lRelease the reset button.

nTo reset during power up, hold the reset button while the access point is powering up.

The system status LED will flash again within 15 seconds indicating that the reset is completed. The access

point will now continue to boot with the factory default settings.

To toggle the system status LED between “normal” (default after power on) and “off” mode, during the

normal operation of the access point, shortly press the reset button for less than 10 seconds.

Micro-B Console Port

To create a console connection to the access point, follow these steps:

1. Connect the console port on the access point to the serial port on the computer using the proprietary

Aruba AP-CBL-SERU cable or AP-MOD-SERU module, which need to be purchased separately.

2. Start the terminal emulation software on the computer and configure a new serial session with the

following settings:

nSpeed: 9600 bps

nData bits:8

nStop bits: 1

nParity: None

nFlow control: None

3. Start the terminal emulation session.

4. Press Enter once. If the connection is sucessful, you are prompted to login.

For this console port pin-out details, refer to Figure 4.

Figure 4 Micro-B Console Port Pin-out

1: NC

2: RXD

3: TXD

4: GND

5: GND

If needed, the AP console driver can be found at the Aruba support portal.

When the access point is in factory default state the console interface (both physical port and BLE) is

enabled with default credentials (username is “admin” and password is the serial number of the unit).

Once the AP has established a connection with its management platform, the console port state

(enabled/disabled) and access credentials are updated to match what’s configured there. State and

credentials are maintained if the AP is power-cycled or rebooted.

Ethernet Ports

The 600R Series access point has five Ethernet ports (E0 - E4), shown in Figure 3.

nThe E0 port is a 100/1000Base-T auto-sensing MDI/MDIX uplink port .

nThe E1 port is a 100/1000/2500Base-T auto-sensing MDI/MDIX port, which can be configured as a

secondary uplink port or downlink port by system management software.

nThe E2- E4 ports are 100/1000Base-T auto-sensing MDI/MDIX downlink ports. E4 port is the PoE out port

and capable to supply PoE power to a 802.3af-compliant device that is phisically connected to the E4

port by Ethernet cable.

Ethernet Port LEDs

Each of the E0-E3 ports has one LED located on the left side, indicating the network status or activity on the

port.

The E4 port has two LEDs located on both sides, the left LEDindicating the network status or activity on the

port, while the right LEDindicating the PoE powering status when the access point is operating as a Power

Sourcing Equipment (PSE). See Figure 3 and Table 3

Rev 03 | August 2023 | 5

6| Rev 03|August 2023

LED Color/State Meaning

Left Off Meet one of the following conditions:

naccess point is powered off

nport is disabled

nno link established

Green - blinking Activity detected on the port

Green - solid Link established at optimum speed (1Gbps or 2.5Gbps)

Amber - solid Link established at reduced speed (100Mbps)

Right (E4 only) Off Meet one of the following conditions:

naccess point is powered off

naccess point is not supplying PoE power

Green - blinking Access point is negotiating PoE power with the device con-

nected to this port.

Green - solid Access point is supplying PoE power to the device

connected to this port.

Table 3: Ethernet Port LEDs

USB interface

The USB 2.0 USB-A interface is compatible with selected cellular modems and other peripherals. When

active, this USB interface can supply up to 5W/1A to a connected device.

When the access point is in factory default state the USB host interface is powered and enabled, assuming

the AP is not in a restricted power mode. On some AP models the USB port may be disabled when a POE

source with insufficient power budget is used. Once the AP has established a connection with its

management platform, the USB host interface state is updated to match what’s configured there. This

state is maintained if the AP is power-cycled or rebooted.

BLE Radio Default State

When the access point is in factory default state the integrated BLE radio is enabled. This applies to the

non-TAA product SKUs only. On the TAA products, the BLE radio is disabled when the unit is in factory

default conditions. Once the AP has established a connection with its management platform, the BLE radio

state is updated to match what’s configured there. This state is maintained if the AP is power-cycled or

rebooted.

Kensington Lock Slot

The access point is equipped with a Kensington lock slot for additional physical security.

DC Power Port

The DCpower port is designed for use with the Aruba AP-AC2-48C power adapter (included in the

package).

After inserting the L-shape DC connector into the DCpower port, users can rotate the DCconnector by 90

degrees and route the power cord to the left of the DC power port. See Figure 5 and Figure 6.

Figure 5 Connecting Power Adapter to DC Power Port

Figure 6 Routing Power Cord

Access Point Installation

All Aruba access points should be professionally installed by a professional installer. The installer is responsible for

meeting applicable national and electrical codes. Failure to properly install this product may result in physical injury

and/or damage to property.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit

s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques

nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et

/ ou des dommages matériels.

For indoor use only. The access point, power adapter, and all connected cables are not to be installed outdoors. This

stationary device is intended for stationary use in partly temperature controlled weather-protected environments

(class 3.2 per ETSI 300 019).

You can put the 600R Series access point on any flat surface such as a desktop.

Installing the SIM Card (For AP-605R Bundle Only)

To use the AP-605CM12 cellular module, you need to install a SIM card to the SIMcard tray on the AP-

605CM12 cellular module. The SIM card tray has two SIMcard slots - SIM slot 1 and SIM slot 2. At any given

Rev 03 | August 2023 | 7

8| Rev 03|August 2023

time, only one SIM card is active and functional, the SIM slot 1 and SIM slot 2 can not be used

simultaneously. If you have only one SIM card, it is recommended to insert your SIM card to the SIM slot 1.

To install a SIM card into the SIM tray, perform the following steps:

1. Remove the AP-605CM12 cellular module from the AP-605R access point.

a. Unfasten the two M3 captive screws using a Phillips screwdriver

b. Press the mounting tab on the cellular module, and pull the cellular module out. See Figure 7.

Figure 7 Removing Cellular Module from the Access Point

1 Captive screws

2 Mounting tab

2. Find the SIMejector needle at the bottom of the cellular module. See 2

Figure 8 SIM Ejector Needle Location

3. Insert the SIM ejector needle into the small hole on the SIM card tray. The SIM card tray will pop open.

See Figure 9.

Figure 9 Opening the SIM Card Tray

4. Pull out the SIM card tray and insert a SIMcard into the SIM tray.

5. Push the SIMcard tray back into the slot. See Figure 10.

Figure 10 Inserting a SIM Card

6. Align the AP-605CM12 cellular module with the opening in the access point.

7. Insert the AP-605CM12 cellular module into the access point and tighten the two M3 captive screws

using a Phillips screwdriver. See Figure 11.

Rev 03 | August 2023 | 9

10 | Rev 03|August 2023

Figure 11 Installing Cellular Module onto Access Point

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software

Quick Start Guide.

Aruba access points are classified as radio transmission devices, and are subject to government regulations of the

host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this

equipment is in compliance with their country’s regulations. For a complete list of approved channels in your

country, refer to the Aruba Downloadable Regulatory Table at

https://www.arubanetworks.com/techdocs/DRT/content/home.htm.

Verifying Post-Installation Connectivity

The integrated LEDs on the access point can be used to verify that the access point is receiving power and

initializing successfully. See Table 1,Table 1 and Table 3.

Electrical and Environmental Specifications

Electrical

nEthernet:

lE0 port:100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

lE1 port:100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

lE2 port:100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

lE3 port:100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

lE4 port:100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port, supporting

PoE-PSE to a 802.3af-compliant device.

nPower

l48V DC power interface, support powering through AC-to-DC power adapter

lMaximum power consumption:Refer to datasheet

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Point d'accès sans fil

HP DESKJET 350 Manuel utilisateur

HP MSM410 Manuel utilisateur

HP MSM310 Manuel utilisateur

HP MSM466-R Manuel utilisateur

HP Compaq Presario,Presario 650 Manuel utilisateur

HP MSM335 Manuel utilisateur

HP ProCurve 420 Manuel utilisateur

HP 425 - Notebook PC Manuel utilisateur

HP MSM320 Manuel utilisateur

HP Aruba AP-374 Instructions de montage

HP MSM325 Manuel utilisateur

HP MSM430 Manuel utilisateur

HP Aruba AP-587 Instructions d'installation

HP MSM323-R Manuel utilisateur

HP Aruba 310 Series Manuel utilisateur

HP J9374A Guide d'installation

HP MSM320-R Manuel utilisateur

HP M210 802.11n Manuel utilisateur

HP HP417 Instructions de montage

HP AP-575 Manuel utilisateur

HP Aruba AP-377 Instructions de montage

HP 425 - Notebook PC Manuel utilisateur

HP WL520 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur