HP T1500 XR Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels HP UPS

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur

hp ups T1500 xr/T2200

xr models extended

runtime module

installation instructions

Read Instructions Completely

Before Beginning Installation Procedures

Hewlett-Packard Company shall not be liable for technical or editorial errors or

omissions contained herein. The information in this document is provided “as is”

without warranty of any kind and is subject to change without notice. The warranties

for HP products are set forth in the express limited warranty statements

accompanying such products. Nothing herein should be construed as constituting an

additional warranty.

HP UPS T1500 XR / T2200 XR Models Extended Runtime Module Installation

Instructions

Second Edition (August 2002)

Part Number 215493-022

215493- 022

Overview

These instructions show how to install an extended runtime

module (ERM). The ERM can be connected directly to a

T1500 XR or T2200 XR model, or to another ERM. Up to two

ERM units can be connected. Depending on the load, one ERM

can extend the available UPS runtime by up to 15 minutes.

Important Safety Information

Before installing this product, read the Important Safety

Information document provided.

WARNING:

• The installation of this product must be performed by

individuals who are knowledgeable about the procedures,

precautions, and hazards associated with AC and DC power

products.

• There are no user-serviceable components inside.

Regulatory Compliance Information

All regulatory certifications for this product were obtained under

the agency series number EO3019B. The corresponding part model

number is 218969-B21.

Weight

29 kg

64.5 lb

WARNING: The ERM weighs 29 kg (64.5 lb) when fully

assembled. To prevent personal injury or damage to

the equipment:

• Observe local occupational health and safety

requirements and guidelines for manual material

handling.

• Obtain adequate assistance to lift and stabilize the

product during installation or removal.

Checking the Battery

Recharge Date

Before unpacking the ERM, check the battery recharge date

specified on the battery recharge date label that is affixed to the

shipping carton.

IMPORTANT: Do not use the battery if the recharge date has passed. If the

date on the battery recharge date label has passed without the battery being

recharged, contact an HP authorized service representative for directions.

NOTE: The following label is only an example date. The date on your carton

may be different.

THIS PRODUCT CONTAINS

A NONSPILLABLE BATTERY

Next Recharge Date:

14-DEC-04

Please refer to Maintenance Section

of Owner's Manual enclosed inside

Kit Contents

Documentation

• Important Safety Information guide

• International Regulatory Compliance guide

• This document

ERM

• ERM chassis

Cables

• ERM power cable (attached to unit)

Preparing for Installation

Powering Down the UPS

To power down the UPS:

1. Shut down all load devices.

2. Press the Standby button to take the UPS out of Operate mode.

Power to the load receptacles ceases.

3. Disconnect the UPS from utility power.

4. Wait at least 60 seconds while the UPS internal circuitry

discharges.

Unpacking the ERM

Carefully remove the kit contents from the shipping box following

proper safety guidelines. Verify that all components are present.

Completing the ERM Assembly

Connecting the ERM to the UPS

1. Verify that the power to the UPS is off.

2. Plug the ERM cable into the connector located at the rear of the

UPS in the lower left corner.

NOTE: UPS appearance varies depending on the particular UPS ordered.

Refer to the UPS user guide for the specific ERM connector location.

3. To install a second ERM, plug the cable from the second ERM

into the socket at the rear of the first ERM.

Charging the Batteries

Allow the batteries to charge before putting the ERM into service.

IMPORTANT: The battery pack charges to:

• 90% of its capacity within 4 hours.

• 100% of its capacity within 24 hours.

Charge the batteries for at least 24 hours before using them to supply

power to your devices.

For more information, refer to the HP website at

www.hp.com/products/ups