HP StorageWorks 2/16 - SAN Switch Manuel utilisateur

addendum

Printed in the U.S.A. March 2003

Product names mentioned herein may be trademarks of their respective companies as reflected by an associated

footnote. The information in this document is subject to change without notice.

This addendum only applies to the following documents:

HP StorageWorks SAN Switch 2/32 Installation Guide, Version 4.0.x

AA–RTQVB–TE (February 2003)

HP StorageWorks SAN Switch 2/16 Installation Guide, Version 3.0.x

AA–RR84B–TE (February 2003)

HP StorageWorks SAN Switch 2/8 Installation Guide, Version 3.0.x

AA–RSB6B–TE (February 2003)

hp StorageWorks

SAN switch universal rack mount

kit installation

Product Version: V3.0.x/V4.0.x

Pen-and-ink Changes

2 SAN Switch Universal Rack Mount Kit Installation Addendum

This addendum consists two parts:

■Pen-and-ink Changes—provides instructions for locating specific text and

either deleting text, replacing text with new text, or adding new text at a

specific location.

■Page Additions—identifies where to add a page at a specific place in the

document and recommends how to attach the replacement pages.

Note: If the changes within this addendum are not incorporated into the specified

documents and then used, problems might arise from using obsolete information.

Pen-and-ink Changes

There are no pen-and-ink changes in this addendum.

Page Additions

The following pages describe the installation of the SAN Switch 2/32, SAN

Switch 2/16, and SAN Switch 2/8 in an HP Series 9000 or comparable EIA rack,

or in an HP System/e rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

For each document, insert the following sheets as shown here:

1. After page 30 in the HP StorageWorks SAN Switch 2/32 Installation Guide

2. After page 29 in the HP StorageWorks SAN Switch 2/16 Installation Guide

3. After page 32 in the HP StorageWorks SAN Switch 2/8 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Installing the Switch in a Rack Using the SAN Switch Universal

Rack Mount Kit

This section provides instructions for installing the SAN Switch 2/32, SAN

Switch 2/16, or SAN Switch 2/8 in an HP System/e rack, or in an HP 9000 Series

or comparable EIA rack using the SAN Switch Universal Rack Mount Kit, part

number 331148-B21.

Figure 1: SAN Switch 2/16 rack-mounted switch

Note: The Universal Rack Mount Kit installation requires two technicians.

The following items are required to install the switch in a rack:

■SAN Switch 2/32, SAN Switch 2/16, or SAN Switch 2/8

■Power cables

■#2 Phillips screwdriver

■7/16-inch wrench or socket

■The SAN Switch Universal Rack Mount Kit rails and rail mounting hardware

listed below:

(2) Rear mounting brackets

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

A right inner rail and a right outer rail

A left inner rail and a left outer rail

(14) #8-32 x 3/16-inch Phillips pan-head screw with captive

star lock washer

(10) #10-32 x 1/2-inch Phillips pan-head screw with captive

star lock washer

(8) #10 alignment washer

(8) #10 adapter washer

(2) 1/4-20 hex nut with captive star lock washer

(2) 1/4-inch flat washer

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Caution: For proper airflow, the SFP media side of the SAN Switch 2/32,

SAN Switch 2/16, or SAN Switch 2/8 must face the rear of the rack. This

mounting allows air to enter from the front of the rack and to exhaust at the

rear of the rack, similar to other rack-mounted equipment. This prevents switch

overheating, which may cause it to fail.

To install the switch in a rack:

1. Check contents of the shipping carton to verify all the required parts and

hardware are available.

2. Choose a mounting location in the rack for the switch.

3. Attach the rear mounting brackets to the rear rack uprights by completing one

of the following steps:

— For an HP 9000 Series or comparable EIA rack, assemble each of the two

brackets with (2) #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and (2) #10 adapter washers as shown in Figure 2.

Figure 2: Installing the rear mounting brackets (HP 9000 Series or comparable EIA

rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install each of the two rear mounting brackets

with (2) #10-32 x 1/2-inch Phillips pan-head screws and (2) #10

alignment washers as shown in Figure 3.

Figure 3: Installing the rear mounting brackets (HP System/e rack-left rear upright)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

Note: This kit contains both left rails and right rails. The rails are marked with

Right

and

Left

to distinguish the rails from each other.

4. Assemble the outer rails by completing the following steps:

a. Attach the left outer rail and the right outer rails to the rear mounting

brackets using (2) 1/4-20 hex nuts with captive star lock washers attached

loosely as shown in Figure 4. Don’t tighten them. The nuts will be

tightened later in step 8.

Figure 4: Installing the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

b. Depending on the rack you are using, complete one of the following tasks:

— For an HP 9000 Series or comparable EIA rack, install two #10-32 x

1/2-inch Phillips pan-head screws with captive star lock washers and two

#10 adapter washers in the upper and lower hole locations of the right rail.

Then install two #10-32 x 1/2-inch Phillips pan-head screws with captive

star lock washers and two #10 adapter washers in the upper and lower

hole locations of the left rail. See Figure 5.

Figure 5: Assembling the outer rails (HP 9000 Series or comparable EIA rack)

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

— For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head

screws with captive star lock washers and two #10 alignment washers in

the upper and lower hole locations of the right rail. Then install two

#10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers

and two #10 alignment washers in the upper and lower hole locations of

the left rail. See Figure 6.

Figure 6: Assembling the outer rails (HP System/e rack)

5. Determine the number of #8-32 x 3/16-inch Phillips pan-head screws with

captive star lock washers required to assemble the inner rails by referring to

Table 1.

Table 1: Number of screws required to assemble the inner rails

Switch

Number of #8-32 x 3/16-inch

Screws

SAN Switch 2/32 12

SAN Switch 2/16 10

SAN Switch 2/8 14

Installing the Switch in a Rack Using the SAN Switch Universal Rack Mount Kit

Addendum Pg

HP StorageWorks SAN Switch 2/8|16|32 Installation Guide

6. For the SAN Switch 2/32 and SAN Switch 2/16, perform step a. For the SAN

Switch 2/8, perform step b.

Caution: Do not use any other screws other than the fourteen that are

provided. Use of any longer lengths can cause damage to internal components

Note: The inner rails work for all three SAN switches—SAN Switch 2/32, SAN Switch

2/16, and SAN Switch 2/8. The mounting holes in the inner rails are marked with 32,

16, and 8. Use the appropriately labeled mounting holes when installing the inner rails

on a switch. For example, to install the inner rails on the SAN Switch 2/32, use the

mounting holes labeled with 32.

When viewing a rack from the front, the left rails are used in the left side of the rack and

the right rails are used in the right side of the rack. The rails must match up—right inner

with right outer and left inner with left outer. Note that the SAN switch mounts in the

rack with its front, the port side, facing the back of the rack. The rear of the switch, the

AC side, faces the front of the rack.

Autres manuels pour StorageWorks 2/16 - SAN Switch

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Changer

HP J4818A Manuel utilisateur

HP 10504 Manuel utilisateur

HP H3C S9500 Guide rapide

HP A7533A - Brocade 4Gb SAN Switch Base Manuel de service

HP 2610 Manuel utilisateur

HP 6125XLG Manuel utilisateur

HP ProCurve 3500yl Series Manuel utilisateur

HP 2600 Series Manuel d'instructions et de sécurité

HP Officejet Pro 7500 Series Manuel utilisateur

HP A5120 EI Series Manuel d'installation

HP ProCurve 2510G Series Manuel utilisateur

HP 8/20q Manuel utilisateur

HP ProCurve 6208M-SX Manuel utilisateur

HP v1810g Manuel utilisateur

HP 5800 Manuel utilisateur

HP A7533A - Brocade 4Gb SAN Switch Base Manuel de service

HP 6125G Manuel utilisateur

HP 377707-002 Manuel utilisateur

HP 10500 series Manuel utilisateur

HP A7533A - Brocade 4Gb SAN Switch Base Mode d’emploi

HP AE370A - Brocade 4Gb SAN Switch 4/12 Manuel utilisateur

HP 2620 series Manuel utilisateur

HP 316095-B21 - StorageWorks Edge Switch 2/24 Mode d’emploi

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur