HP Surestore Tape Library Model 10/180 Manuel utilisateur
configuration
and diagnostic
hp tape library
configuration guide
August 2001
2hptape library configuration guide
1
Configuration 3
Configuring the Host System3
Windows NT4
Sun Solaris 5
HP-UX Hosts 6
Installing the Pass-Through Driver7
HSC or PCI Pass-Through Driver Installation8
Creating a Device File for the Robotics Controller8
Verifying the Installation10
MPE/iX Hosts11
Verifying the Connection 15
Diagnostics 17
Diagnostic support tools17
HP Library & Tape Tools18
Support Tools Manager (STM)19
Performing Operations21
Using the STM Tools21
Reviewing Logs 22
Types of STM Tools for Tape Libraries24
Expert Tools 25
Sysdiag 31
SCSITAC Sections32
SCSIDLT Sections 32
contents
2
1
Configuring the Host System 3
Configuration
Configuring the Host System
Once the library is connected to a host, the Windows NT, Sun
Solaris, HP-UX, and MPE/iXoperating systems must be
configured to recognize it. The procedures are different,
depending on the host system.
4 Configuring the Host System
Windows NT
For Windows NT operating systems, perform the following operating
system configurations:
•Install the appropriate host bus adapter(s)
•Install the corresponding drivers for the interface card(s)
•Install the backup software
To verify the installation, look for the library and drive after powering
up the host.
•Go into Settings -> Control Panel -> SCSI Adapter
•You can also check your installation on Windows NT with HP
diagnostic utilities available from www.hp.com/go/support. See
the Downloads and Drivers section for your library model.
Run a test backup to ensure that all components are properly
configured.
Configuring the Host System 5
Sun Solaris
For Sun Solaris operating systems, perform the following operating
system configurations:
•Install the appropriate host bus adapter(s)
•Install the corresponding drivers for the interface card(s)
•Install the backup software
To verify the installation, look for the library and drive after powering
up the host.
1. Close all open applications and exit the Common Desktop
Environment (CDE).
2. Type “init 0” at any prompt. This will shut down all processes,
and take you to the OpenBoot PROM.
3. Type “reset”.
4. At the OK prompt, type “probe-scsi-all”.
Run a test backup to ensure that all components are properly
configured.
6 Configuring the Host System
HP-UX Hosts
To enable communication between the host and tape library,
appropriate drivers must be configured into the HP-UX kernel. Table
1 shows which drivers are necessary for each device.
NOTE Some drivers have different names, depending on whether or
not they are listed in the output of an ioscan or in the system
file.
Table 1 Drivers Needed
Device Driver Name
In ioscan In system file
SCSI Host Bus Adapter
(HSC or PCI Bus)
c720 c720
Fibre Channel Host Bus Adapter
fcp fcT1_fcp
fcT1 fcT1
fcT1_cntl fcT1_cntl
Fibre Channel Bridge or
Multiplexer
fcpmux fcpmux
Tape Library Robotics Controller
(HSC or PCI Bus)
sctl sctl
Tape Driver (HSC or PCI Bus) stape stape
Configuring the Host System 7
If these drivers are already installed into the kernel, upon system boot
they will automatically be associated with the hardware that they
control. However, if drivers are missing, they must be installed. For
more information on installing Fibre Channel drivers, refer to the
HP
Fibre Channel Mass Storage Adapter Service and User Manual
(A3636-90002)
.
A pass-through driver is used to manage the robotics controller. Since
this driver is not dedicated for this particular device, it must be
manually installed. The following sections describe this process:
•Installing the pass-through driver (below)
•Creating a device file for the robotics controller (page 8)
•Verifying the installation (page 10)
Installing the
Pass-Through
Driver
Obtain information about the peripherals attached to the system:
ioscan -f
The screen should look similar to the following:
Class I H/W Path Driver S/W State H/W Type Description
bc 0 root CLAIMED BUS_NEXUS
bc 1 8 bc CLAIMED BUS_NEXUS Pseudo Bus
Converter
ba 0 8/0 GSCtoPCI CLAIMED BUS_NEXUS PCI Bus Bridge -
GSCtoPCI
ext_bus 1 8/0/2/0 c720 CLAIMED INTERFACE Ultra Wide SCSI
target 3 8/0/2/0.0 tgt CLAIMED DEVICE
autoch 2 8/0/2/0.0.0 schgr CLAIMED DEVICE HP C7200-8000
target 4 8/0/2/0.1 tgt CLAIMED DEVICE
tape 2 8/0/2/0.1.0 stape CLAIMED DEVICE QUANTUM DLT8000
target 5 8/0/2/0.2 tgt CLAIMED DEVICE
tape 4 8/0/2/0.2.0 stape CLAIMED DEVICE QUANTUM DLT8000
8 Configuring the Host System
NOTE HP C7200-8000 is used only as an example. The actual
ioscan output will reflect the product number of the library
you are configuring.
HSC or PCI
Pass-Through
Driver
Installation
The following procedure assumes the use of a SAM terminal mode.
In X-windows (GUI) mode, use the mouse button to select an option.
1. Run SAM.
2. Select Kernel Config, and press Return.
3. Select Drivers, and press Return.
4. Select sctl.
NOTE If Current State is “In,” proceed to Creating a Device File for
the Robotics Controller. Otherwise, continue with the next
step.
5. From the Menu Bar, select Actions. Select Add Drivers to
Kernel, and press Return.
6. From the Menu Bar, select Actions. Select Create New
Kernel, and press Return.
7. A t t h e
Are you sure
prompt, respond
Yes
. Press Return.
8. After the status messages, select OK. Press Return. The system
reboots.
Creating a
Device File for
the Robotics
Controller
1. Use the mknod command to create a device file to access the
robotics controller. The command syntax is:
/user/sbin/mknod /dev/scsi/<devfilename> c
<majornum> <minornum>
•<devfilename> is the user-defined name of the device file.
•<majornum> is the character major number from the lsdev
command.
•<minornum> is the minor number in the format 0xIITL00;
where II is the two-digit card instance number in
hexadecimal; Tis the target SCSI ID number; Lis the LUN
number, and 00 is reserved.
Autres manuels pour Surestore Tape Library Model 10/180
3
Ce manuel convient aux modèles suivants
10
Table des matières
Autres manuels HP Stockage
HP
HP StorageWorks XP10000 - Disk Array Manuel utilisateur
HP
HP StorageWorks XP10000 - Disk Array Manuel utilisateur
HP
HP C4405A - Colorado 14GB Tape Drive Manuel utilisateur
HP
HP Surestore Disk Array 12h - And FC60 Manuel utilisateur
HP
HP Surestore 160ex - Optical Jukebox Manuel utilisateur
HP
HP Storevirtual 4000 Guide de référence rapide
HP
HP SureStore AutoBackup PC100 Manuel utilisateur
HP
HP P9000 Mise à jour du firmware
HP
HP StorageWorks EML E Series Manuel utilisateur
HP
HP 624192-B21 Instructions d'utilisation
HP
HP 8/20q Mode d’emploi
HP
HP XP7 Manuel utilisateur
HP
HP Surestore Disk Array 12h - And FC60 Instructions de montage
HP
HP ProLiant DL100 G2 DPSS Manuel utilisateur
HP
HP P9000 Manuel utilisateur
HP
HP StoreEasy 3000 Manuel de service
HP
HP A5585A - SureStore DLT E Tape Library 4/40 Mode d’emploi
HP
HP StorageWorks MSA500 G2 Manuel utilisateur
HP
HP StorageWorks 12000 Mode d’emploi
HP
HP DW017B - StorageWorks Ultrium 448 Tape Drive Mode d’emploi
Manuels Stockage populaires d'autres marques
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur
Dell
Dell PowerVault MD3600f Series Manuel utilisateur
CFI
CFI TERA STOR SATA RAID IV Manuel utilisateur