HP StorageWorks EML E Series Manuel utilisateur

StorageWorks

EML E-Series

Interface

Manager

Replacement

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure that you

are properly grounded when touching

static sensitive components.

Note: This part is not hot-pluggable.

It is necessary to power down the library

to replace this part.

Open the back door

of the library.

StorageWorks

EML Interface

Manager

Replacement

Instructions

Caution: Parts can be damagedby

electrostatic discharge.Keep p arts in their

containers until needed. Ensure that you

areproperly groundedwhen touching

static sensitivecomponents.

Note:Thispart is not hot-pluggable.

It is necessary to power down the library

toreplace this part.

Openthe backdoor

ofthe library.

StorageWorks

ESL

E-series

Interface

Manager

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartisnothot-pluggable.

Itisnecessarytopowerdownthelibrary

toreplacethisp

art.

10026

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

Powerdownthelibrary.

a.Placethelibraryoff-linebypressingthe

Standbybuttononthelibrary'sfrontpanel.

Thelibraryroboticscompletesanycurrent

commandsandt

henstops.

b.Verifythatthefrontpaneldisplayindicates

“SystemOff-line”.

c.Verifythatt

hepickerisempty.Ifthereisa

tapecartridgeinthepicker,performaMove

commandtoplacethecartridgeinan

availableslot.[Contentneeded.]

d.Pressandholdthepowerbuttonlocatedon

thefrontofthelibrarybehindthelaptoptray

untilthefrontpanelgoesblank.

Flipthetwobreakerswitchesoffatthepower

distributionunit.

Inspectthe contents ofthe kit.

Poweroffthelibrary.

Stop all library activityand ensure thatthe

picker is empty.

Open thedoor at therear oftherack.

Set therack power switch at the upper right

cornerto the OFF position.

Ensure that allpowerindicators on the power

suppliesare off.

IdentifytheInterface Manager.It is located inthe

bottomslotofthebaseunit card cage.

Inspect the contents of the kit.

Power off the library.

a. Stop all library activity and ensure that the

picker is empty.

b. Set the library power switch at the upper right

corner to the OFF position.

c. Ensure that all power indicators on the power

supplies are off.

Identify the Interface Manager. It is located in the

bottom slot of the base module card cage.

TO FIBRE CHANNEL CONTROLLERS NETWORK SERIAL AUX STATUS

ERROR

Replacement

Removal

Memory Module

Relocation

Remove all cables connected to the Interface

Manager, after noting where they are connected.

b. Grasp the edges of the memory module

and slide it out of the flash memory slot.

If needed, push a pen into the corner notches

of the flash memory slot to unseat the memory

module.

c. Remove the replacement Interface Manager

card from its protective sleeve and place it on

your work surface. (This card should also

face battery-side up.)

d. With the connector going in first, align the

sides of the memory module with the flash

memory slot on the replacement Interface

Manager card. Gently slide the memory

module into the slot until it is securely seated.

e. If the memory module does not slide in easily,

the module is upside down. Pull the module

back out, flip it over, and reinsert it into

the slot.

Use a #2 Phillips screwdriver to loosen the

captive screws in the black ejector handles at

both ends of the Interface Manager. Push the

ejector handles toward the outside, then pull on

them to remove the controller.

Align the replacement Interface Manager with the

guides in the base module card cage and slide

the Interface Manager into the library. Push the

ejection handles inward to fully seat the card.

Tighten the captive screws.

Relocate the memory module.

a. Position the existing Interface Manager card

battery-side up to access the memory module.

TO FIBRE CHANNEL CONTROLLERS NETWORK SERIAL AUX STATUS

ERROR

TO FIBRE CHANNEL CONTROLLERS NETWORK SERIAL AUX STATUS

ERROR

Reconnect the cables to the interface controller

exactly as they were connected to the original

board.

Power on the library.

a. Set the library power switch at the upper

right corner to the ON position.

b. Check the power supply power indicators

to verify that the power is on.

cVerify that the library robotics controller

Active indicator is lit.

Verify that the status LEDs of the Interface

Manager card indicate a normal state. For a

description of LED diagnostic codes, refer to the

Troubleshooting chapter of the HP StorageWorks

Interface Manager and Command View TL

installation guide.

Note: Because all of the configuration

settings of the Interface Manager are

stored in the memory module that you

replaced in steps 7 through 9, your

replacement Interface Manager card

retains the configuration of the original

card. To verify or change these

settings, refer to the HP StorageWorks

Interface Manager and Command

View TL user guide.

Getting help

• HP product information:

http://www.hp.com/products/tapestorage

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Close the back door

of the library.

First Edition (May 2005)

Part Number: AD560-96009

*AD560-96009*

AD560-96009

Autres manuels HP Stockage

HP P2000 G3 Guide de référence rapide

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Manuel utilisateur

HP D2D100 Manuel utilisateur

HP 7957A Manuel utilisateur

HP Pavilion p6000 - Desktop PC Mode d’emploi

HP 3PAR StoreServ 7200 2-node Manuel utilisateur

HP 3000 - 37XE System Mode d’emploi

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Manuel utilisateur

HP Surestore 6164 - Switch Manuel utilisateur

HP StoreEver Series Manuel utilisateur

HP StorageWorks DLT80 Manuel utilisateur

HP P9000 Manuel utilisateur

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Mode d’emploi

HP Z Turbo Drive Quad Pro Manuel utilisateur

HP Surestore 160ex - Optical Jukebox Manuel utilisateur

HP XP 9000 Manuel utilisateur

HP 3000 - 37XE System Mode d’emploi

HP StorageWorks XP1024 Guide rapide

HP D2200sb Manuel

HP StorageWorks XP10000 - Disk Array Manuel utilisateur

HP Surestore 6164 - Switch Manuel utilisateur

HP Storevirtual 4000 Guide de référence rapide

HP 345524-B21 Manuel utilisateur

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Mode d’emploi

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur