HP NetStorage 6000 Manuel utilisateur

Autres manuels pour NetStorage 6000

12

Autres manuels HP Stockage

HP

HP StorageWorks 8B - FC Entry Switch Manuel utilisateur

HP

HP 3PAR StoreServ 7200 2-node Manuel utilisateur

HP

HP FIPS 140-2 Manuel

HP

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP

HP LTO-4 Ultrium 1760 Manuel du produit

HP

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP

HP Colorado 5GB Manuel utilisateur

HP

HP MSA 1050 Manuel de programmation

HP

HP StorageWorks 500 Generation 2 Manuel

HP

HP StorageWorks EML E Series Manuel utilisateur

HP

HP P10000 Manuel utilisateur

HP

HP EVA P6000 Mode d’emploi

HP

HP StorageWorks AF204A Guide d'installation

HP

HP Ultrium Drive Manuel du produit

HP

HP Ultrium 215 Instructions d'utilisation

HP

HP LeftHand P4000 - SAN Solutions Supplément

HP

HP DW017B - StorageWorks Ultrium 448 Tape Drive Mode d’emploi

HP

HP HD1600 Manuel utilisateur

HP

HP Pavilion p6000 - Desktop PC Manuel utilisateur

HP

HP STORAGEWORKS MSL4048 Instructions d'utilisation

HP

HP Surestore Disk Array 12h - And FC60 Manuel utilisateur

HP

HP v229g Manuel utilisateur

HP

HP StorageWorks P4000 Series Manuel utilisateur

HP

HP XP20000/XP24000 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur

Network Interface Upgrade

HP NETSTORAGE 6000

Configurations supported:

Any combination of one or two of the following

HP NICs is supported:

•10/100 b

•Dual 10/100 b

•Gigabit 1000 Base SX

Each NIC port must be attached to a different subnet.

runking is not supported.

Parts required:

•New NIC card

Tools required:

•Phillips screwdriver

•Electrostatic protection device

NOTES:

•Use only HP NetStorage 6000 Network Interface Cards for upgrades.

•For this upgrade, you should choose a time when end-user access is not required for the unit.

Shut own the System

Open the Case

A. Remove the two screws on the back of the unit that hold

the top in place.

B. Slide the top backwards, and lift to remove.

A. Shut down the unit using either the front panel interface

or the HP NetStorage web interface.

B. After system shutdown is complete, turn off the power

switch on the back panel of the unit.

C. Disconnect both power cords from the back panel of the

unit.

All manuals and user guides at all-guides.com

all-guides.com

A. Unplug the network cable.

B. Unscrew the existing NIC and gently remove it.

NOTE: If you are installing the NIC in an unused PCI slot,

remove the expansion slot access panel.

A. Select an open PCI slot.

B. Gently place the new card in the slot, and screw it into

place.

A. Slide the top back into place.

B. Using the screwdriver, secure the top to the unit.

Add or Remove a NIC Card

Insert the New Card

Close the Case

A.

B.

All manuals and user guides at all-guides.com

Connect the Unit

A. Connect a network cable to the new port(s).

B. Reconnect the two power cords on the back panel of the

HP NetStorage unit, and plug them into your power source.

C. urn on the unit.

. Press the alarm-reset button on the front panel to turn off

the alarm. he alarm sounds whenever the unit is powered on.

A. Follow one set of the directions below:

•If your system uses DHCP, the LCD panel will display the

IP address of the first NIC port. Move to Step 8.

•If your system does not use DHCP, use the LCD panel and

arrows to configure the IP address, Subnet mask, Broadcast

address, and Gateway address (if needed) for the newly installed

NIC. Move to Step 8.

NOTE: Only one Gateway address is supported, regardless of the

number of NIC ports installed.

Enter Network Information

A.

B.

.

A. Using a computer on the network, open a web browser and enter

the unit's IP address in the browser's address or location field.

B. Select Configuration > Network Settings.

C. ype in or verify the IP address and Subnet Mask for each new NIC

you installed.

. Click Apply.

Use a Web Browser to Enter Network Settings

All manuals and user guides at all-guides.com

*C4480-90101*

C4480-90101

All manuals and user guides at all-guides.com