HP 20/700 Manuel utilisateur

101421 1

CAUTION: HP LSM drives are not customer installable or replaceable. Any servicing,

adjustment, maintenance or repair must be performed only by authorized HP service-

trained personnel.

Note to Customer Engineer: This installation may add new technology to the library

that older user’s guides do not address. Please remind the customer that the latest user

documentation is available from the HP Customer Care website: http://www.hp.com/go/

support.

■Materials Included

■700 LVD SCSI COMPONENT INSTALLATION

If your library contains the second drive tower, you must first remove the MPM card before

installing the low voltage differential SCSI adapter card. If this does not apply to your

library, skip the following section and begin with MPW card installation, Section B.

A. MPM Removal

1. Be sure that the operator has the library and all drives offline.

2. Open the right front door.

3. Remove power from the library and drives by pushing the main circuit breaker down (off).

4. Using a 3/16 hex driver, remove the customer SCSI Y cable from the MPC card and lower

bulkhead. Discard the cable and the screwlocks that hold the connector to the lower

bulkhead (see Figure 1).

Table 1. Materials List

Part Quantity

I/I CPCI Interface 1

CPCI Card Cage Assembly 1

Cover, EM Module 1

#4-40 x 3/8 Screws 3

#6-32 x 3/8 Screws 8

Terminator 1

SCSI Cable 1

LVD SCSI Icon 1

HP CPCI Interface Kit With LVD SCSI Adapter

Card

(for HP Field Service Use Only)

Figure 1.

5. Using a Torx T-15 driver, remove the four Electronics Module (EM) cover screws on the

front and the two on the side and remove the cover (retain screws). Refer to Figure 2.

Figure 2. EM Cover Removal

Figure 3. Grating under Electronic Module

WARNING:

THE CURRENT GRATING UNDER THE ELECTRONICS MODULE

ALLOWS SMALL ITEMS (NUMBER 4 SCREWS) TO FALL THROUGH

THE FAN ASSEMBLIES. LIKEWISE, THE GRATING ON TOP OF THE

POWER SUPPLIES (IDENTICAL) WOULD ALLOW SMALL ITEMS

DROPPED FROM ABOVE TO FALL THROUGH AND INTO THE DC

POWER SYSTEM. AT THIS TIME WE ADVISE PLACING A PIECE OF A

CARDBOARD OR AN ESD BAG UNDER THE MPC CONTROLLER

(BOTTOM OF THE ELECTRONICS MODULE) WHILE REMOVING THE

MPM AND WHILE ATTACHING THE CPCI CARD CAGE. BE SURE TO

REMOVE AFTER INSTALLATIONS ARE COMPLETE (SEE FIGURE 3).

6. Disconnect the P/J242 and P/J243 connectors from the MPM card. Disconnect cable from

bulkhead (as shown in Figure 4).

Figure 4. MPM Card Components

7. Using a 3/8-in. hex driver, remove the upper and lower MPM card nuts (see Figure 5).

8. Using a Torx T-10 driver, remove the center MPM card screw (see Figure 5).

9. Pull back slightly and turn the card to the left to remove the mounting plate from the two

studs.

10. Remove the MPM card and bracket. Set aside to be reinstalled in Section C.

Figure 5. MPM Card Attach

B. MPW Card Installation

If you used Section A to remove the MPM card, skip to Step B5. Otherwise, begin with

Step 1.

1. Open the right front door.

2. Remove power from the library and drives by pushing the main circuit breaker down (off).

3. Remove the customer SCSI Y cable from the MPC card and lower bulkhead. Discard the

cable and the screwlocks that hold the connector to the lower bulkhead (see Figure 1).

4. Using a Torx T-15 driver, remove the four Electronics Module (EM) cover screws on the

front and the two on the side and remove the cover (retain screws). Refer to Figure 6.

Figure 6. EM Cover Removal

WARNING:

THE CURRENT GRATING UNDER THE ELECTRONICS MODULE

ALLOWS SMALL ITEMS (NUMBER 4 SCREWS) TO FALL THROUGH

THE FAN ASSEMBLIES. LIKEWISE, THE GRATING ON TOP OF THE

POWER SUPPLIES (IDENTICAL) WOULD ALLOW SMALL ITEMS

DROPPED FROM ABOVE TO FALL THROUGH AND INTO THE DC

POWER SYSTEM. AT THIS TIME WE ADVISE PLACING A PIECE OF A

CARDBOARD OR AN ESD BAG UNDER THE MPC CONTROLLER

(BOTTOM OF THE ELECTRONICS MODULE) WHILE REMOVING THE

MPM AND WHILE ATTACHING THE CPCI CARD CAGE. BE SURE TO

REMOVE AFTER INSTALLATIONS ARE COMPLETE (SEE FIGURE 7).

Figure 7. Grating under Electronic Module

CAUTION: Possible ESD damage. FOLLOW ESD PRECAUTIONS.

5. The card and its card cage are collectively termed “Compact Peripheral Component Inter-

connect”(CPCI). Open the CPCI package and remove the card from the anti-static bag.

6. Remove the MPW card from the CPCI. Loosen the captive screw using a Phillips screw-

driver (see Figure 8).

Figure 8. MPW Card Secure

7. Disengage the latch.

8. Gently pull on the MPW card to release it from the MPV connector.

9. Slide the MPW card out of the card cage.

10. Place the MPW card on a static-free surface (you may use the anti-static bag).

CAUTION: Possible equipment damage: PUSH THE MPV CARD STRAIGHT

IN, BEING CAREFUL NOT TO DAMAGE THE CONNECTOR TO THE MPC

CARD.

11. Locate the MPV connector provided on the MPC card at J211. Gently mate the MPV card

with the MPC card connector (see Figure 9).

Figure 9. MPC Card Components

12. Install the three mounting screws (4-40 x 3/8) through the three cutouts in the card cage.

These screws go into the MPC card standoffs (see Figure 10).

Figure 10. CPCI Card Cage

CAUTION: Possible ESD damage. FOLLOW ESD PRECAUTIONS.

13. Obtain the MPW card. The MPW card is inserted into the CPCI card cage as described in

the next step.

14. Hold the card so that the card connector aligns with the MPV card connector (circuit side

out, components facing the MPC card).

15. Slide the MPW card onto the guide rail and gently push it until it mates with the MPV card

connector (see Figure 11).

Figure 11. MPW Card Install

16. Make sure the card latch engages (see Figure 8 for Steps 16 and 17).

17. Using a Phillips screwdriver, tighten the captive screw.

Note: If you removed an MPM card, skip to Step 20 otherwise, complete Steps 18

and 19 before proceeding.

18. Remove the ESD bag or cardboard from the grating.

19. Install the new EM cover, using six No. 6-32 x 3/8 screws on the front and two on the side.

NOTE:

ONLY THE LOWER SLOT IS

SUPPORTED AT THIS TIME.

BE SURE TO INSERT THE MPW

CARD INTO THAT SLOT.

Note: The library must be at the end of the SCSI bus as shown in Figure 12.

Devices can be host bus adapter, tape drives, other libraries, etc. Figure 12

depicts the actual physical location on the bus and not the SCSI ID.

Figure 12.

20. Connect the feed-through terminator to the connector on the MPW card.

21. Connect the male connector, on the single SCSI cable, to the connector on the feed-

through terminator (see Figure 13).

Figure 13. SCSI Cable Routing

22. Using a 3/16 hex driver, connect the two provided screwlocks through the left side of the

bulkhead into the SCSI cable connector (see Figure 14).

Note: Do not use original screwlocks removed in Step 3. Use the new

screwlocks provided in the kit.

23. Obtain the LVD SCSI icon and place it next to the connector on the bulkhead (see Figure

14).

24. Secure the cable in the strain reliefs.

Figure 14.

Autres manuels pour 20/700

Autres manuels HP Stockage

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manuel utilisateur

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manuel utilisateur

HP P9000 Manuel utilisateur

HP StorageWorks 2000fc Manuel utilisateur

HP Brio 71xx Manuel utilisateur

HP StorageWorks NAS b2000 - v2 Manuel d'utilisation

HP StorageWorks XP1024 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

HP Data Vault Fiche technique

HP STOREEVER LTO 4 Manuel utilisateur

HP S700 Pro 2.5 Manuel utilisateur

HP Surestore 6164 - Switch Manuel utilisateur

HP DAT-160 Manuel utilisateur

HP EX950 M.2 Manuel utilisateur

HP StorageWorks 3800ux Manuel utilisateur

HP P6080-63001 - Maxtor DiamondMax Plus 40 GB Hard... Manuel utilisateur

HP AJ750A - StorageWorks Modular Smart Array 2000 Dual I/O Storage... Mode d’emploi

HP StorageWorks 8B - FC Entry Switch Manuel utilisateur

HP A5272A - SureStore E Disk System SC10 Storage... Manuel utilisateur

HP EVA P6000 Manuel de service

HP Pavilion p6000 - Desktop PC Manuel utilisateur

HP Surestore Disk Array 12h - And FC60 Instructions de montage

HP StorageWorks P2000 Manuel utilisateur

HP StorageWorks DAT320 USB Mode d’emploi

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur