HP ProLiant SL160s Manuel utilisateur

HP ProLiant Power Interface Control (PPIC) Utility

User Guide

Abstract

This guide is for HP ProLiant SL customers and Firmware installers. This guide describes chassis/rack architecture, power management, control

utilities, and command and options descriptions for select HP ProLiant servers.

Part Number: 583301-005

March 2011

Edition: 5

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Microsoft and Windows Server are U.S. registered trademarks of Microsoft Corporation.

Contents 3

Contents

Introduction.................................................................................................................................. 4

New chassis/rack architecture.................................................................................................................... 4

Power Management Controller.................................................................................................................... 4

Power Measurement...................................................................................................................... 5

Power Measurement .................................................................................................................................. 5

Commands description.................................................................................................................. 6

Help menu ............................................................................................................................................... 6

Display chassis power level and configuration .............................................................................................. 6

Poll chassis power level.............................................................................................................................. 6

Verbose ................................................................................................................................................... 6

Calibrate and display power limits .............................................................................................................. 7

Set power configuration mode .................................................................................................................... 7

HP ProLiant Power Interface Control (PPIC) Utility.............................................................................. 9

Command line utility.................................................................................................................................. 9

Supported OSs ......................................................................................................................................... 9

Synopsis .................................................................................................................................................. 9

Options description ................................................................................................................................... 9

Select communication bus................................................................................................................. 9

Select output log filename................................................................................................................. 9

Configuration examples ............................................................................................................................. 9

Introduction 4

Introduction

New chassis/rack architecture

The new line of HP ProLiant s6500 Scalable Server, HP ProLiant DL1000/DL2000 Multi-Node Server, and

HP ProLiant SL6000 Scalable Servers implement entirely new chassis/ rack architecture in the industry

standard server market space, producing the most power efficient and power manageable servers in the

world. Each 2U chassis consists of up to 4 nodes and up to 4 fans. Each 4U chassis consists of up to 8 nodes

and up to 8 fans. Each chassis also contains an embedded microcontroller that provides power metering and

throttling capabilities for the entire chassis.

Power Management Controller

As depicted in the above diagram, the embedded Power Management Controller is able to monitor power

consumption for all aspects of the 2U/4U chassis and throttle the speed of the processors and memory in

each node within the 2U/4U chassis in order to maintain a pre-set power budget.

Power Measurement 5

Power Measurement

This utility displays the power reading calculated by the chassis Power Management Controller.

As with any measurement system, variations in temperature, input power, and system loads will impact the

accuracy of the power calculations. All power reading displayed by this utility will have a -/+ 5% tolerance.

Commands description 6

Commands description

PPIC can only process one command at a time.

Help menu

-h:

This command will display a summary of supported commands and options.

Display chassis power level and configuration

-d:

This command will display the instantaneous power reading for the entire chassis:

1. Total Chassis Power (AC): the sum of all power consumed by all present nodes and chassis subsystems.

2. Set Power Configuration Mode for more information.

Poll chassis power level

-p -ffrequency -tduration:

This command will poll the chassis status and configuration every frequency seconds for a total duration of

duration seconds:

1. Total Chassis Power (AC): the sum of all power consumed by all present nodes and chassis subsystems.

Enabling verbose mode (-v) will provide detailed information about the chassis power consumption.

Verbose

-v:

This command will only affect the output of Display chassis power level and configuration and Poll chassis

power level. Enabling verbose will provide detailed information about the chassis power consumption:

1. Maximum Chassis Power Available (AC): the total power supply capacity available in the chassis.

2. Total Chassis Power (AC): the sum of all power consumed by all present nodes and chassis subsystems.

3. Total Chassis Peak Power (AC): the highest calculated power value for the chassis since it was last

cleared.

4. Total Chassis Peak Power (DC): the highest calculated power value for the chassis since it was last

cleared.

5. Bay Power (DC): the instantaneous power consumption calculated at each bay. (Example: A 2U node

connected on bay 3 will have a total power consumption of bay 3 plus bay 4)

6. Total Fan Power (DC): instantaneous fan power consumption of all active fans in the chassis.

Commands description 7

7. Set Power Configuration Mode for more information.

Calibrate and display power limits

-c:

This command will force the system to idle state to get the lowest possible power configuration. Once the

value has been obtained the system will display the updated information:

1. Maximum Chassis Power Available (AC): the total power supply capacity available in the chassis.

2. Minimum Chassis Power Achieved (AC): the lowest power achieved at idle with the current system

configuration.

3. Power Limits (AC): the power range the Power Control Mode will guarantee full operation.

4. Set Power Configuration Mode for more information.

NOTE: System performance will degrade while acquiring Power Profile.

NOTE:

When Power Control Configuration Mode is set to User Configurable (3), the system will

return to the default Power Control Configuration Mode (1) after system calibration completes.

The user is responsible for setting a new Power Control Configuration Mode and level.

Set power configuration mode

-s -mmode -lpower:

This command will update the chassis Power Control Configuration Mode. The Power Management Control

table shows the valid values for mode. Power is required when setting Power Control Configuration to User

Configurable.

Mode Configuration

No Redundancy

Power throttling disabled.

1 AC Redundancy with throttling (Default mode)

This provides Maximum Performance with PS Redundancy. Power control logic will only throttle the

performance of each node in the case where the total power draw by the chassis attempts to exceed

the power supply capacity. In this mode, the box is expected to survive an unexpected AC Power loss

to one of the power supplies.

2 Full AC/DC Redundancy

Power control logicl maintains a power cap value at the DC rating of a single power supply

(Example: 460W, 750W, or 1200W), such that if one power supply experiences a DC or AC

failure, the chassis remains on-line and operational. User must be cognizant of the minimum power

consumption of the chassis and this must be less than the rating of a single power supply.

3 User Configurable (Available only with the LO100/iLO Advanced Pack)

User specifies the power envelope for the chassis, within the capabilities of the HW installed. Before

setting this mode, it is required that the user run PPIC's Calibrate and display power limits command

to obtain the minimum and maximum power consumption envelope for the chassis. In order to avoid

punitive performance due to throttling,do not set a User Configurable Power Control Mode limit value

Commands description 8

Mode Configuration

below or within 20% of the minimum power value obtained during system calibration.

Recommended steps to properly define the Power Control Configuration level for User Configurable (3) mode:

1. Run the target system (all nodes in chassis) at the production level load.

2. Calibrate the chassis to obtain the power profile and display the information (ppic -c).

3. Set the Power Control Configuration Level within the specified Power Capping Limit Range obtained in

the step (ppic -s -m3 -lpower, where power is the preferred set point in Watts AC).

4. Verify the chassis power level and configuration enabling verbose mode (ppic -d -v).

5. Monitor chassis power is within 5% of desired power level set point (ppic -p -f1 -t10).

NOTE:

When Power Control Configuration Mode is set to User Configurable (3), the system will

return to the default Power Control Configuration Mode (1) after system calibration completes.

The user is responsible for setting a new Power Control Configuration Mode and level.

HP ProLiant Power Interface Control (PPIC) Utility 9

HP ProLiant Power Interface Control (PPIC) Utility

Command line utility

HP provides a simple command line utility, called PPIC, for monitoring and configuring the power control

configuration of the SL product lines.

The PPIC utility must only be executed through one server node per chassis.

Supported OSs

Versions of this utility are available for Microsoft Windows Server OS (2008 and 2008 R2) and Linux OS

(RHEL5 and SLES11) with the requirement that the OS IPMI Driver be installed.

Synopsis

ppic [-h] [-d] [-v] [-p -ffrequency -tduration] [-c] [-s -mmode -lpower] [-bbus]

[-ofilename]

Options description

These options need to be specified with a valid command to be processed.

Select communication bus

-bbus:

This option allows overriding the default communication bus to the Power Management Controller. Changing

the default communication bus might prevent PPIC from working properly.

Select output log filename

-ofilename.log:

This option allows overriding the output filename, where filename is the filename and log is the extension. By

default, the screen output is also saved into the ppic.log. Every time this utility is executed, the default log is

overwritten with the latest output.

Configuration examples

Display chassis power level and configuration and store output in power.log file

ppic -d -opower.log

Poll chassis power level every 1s for 10 minutes and enable verbose mode

ppic -p -f1 -t600 -v

HP ProLiant Power Interface Control (PPIC) Utility 10

Set Power Configuration Mode to AC Redundancy with throttling (Default Mode) and store output in

config.log

ppic -s -m1 -oconfig.log

Autres manuels pour ProLiant SL160s

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Logiciel

HP StorageWorks SN6000 Manuel utilisateur

HP Rx2620-2 - Integrity - 0 MB RAM Manuel utilisateur

HP Integrity rx1600 Guide de référence rapide

HP TR3271 Manuel du propriétaire

HP HPE XP P9500 Mode d’emploi

HP BB118BV - StorageWorks Data Protector Express... Instructions d'installation et d'utilisation

HP C7791C - DesignJet 130 Color Inkjet Printer Guide de configuration

HP HPE XP P9500 Guide de sécurité

HP JetCAPS Manuel utilisateur

HP StorageWorks 2/140 - Director Switch Mode d’emploi

HP t5630 - Thin Client Instructions d'installation et d'utilisation

HP Compaq Presario,Presario 4400 Mode d’emploi

HP BladeSystem Dual NC370i - Multifunction Network... Manuel utilisateur

HP BL30p - ProLiant - 1 GB RAM Manuel utilisateur

HP HP Integrated Lights-Out Manuel utilisateur

HP HPE XP P9500 Mode d’emploi

HP iPAQ 4500 Guide d'installation

HP OmniBook 2100 Manuel utilisateur

HP PROCURVE 2520 Manuel utilisateur

HP Media Center m1000 - Desktop PC Guide de démarrage rapide

HP B6960-96035 Manuel utilisateur

HP Integrity BL860c Manuel utilisateur

HP Designjet T1300 Manuel utilisateur

HP NonStop Pathway/iTS Manuel du propriétaire

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur

Novell

Novell SP2 - S Mode d’emploi