HP MC68040 Manuel utilisateur

User’s Guide for the Graphical User Interface

MC68040/EC040/LC040

Emulator/Analyzer

(HP 64783A/B)

Notice

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose. Hewlett-Packard shall not be liable for errors

contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information, which is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of

Hewlett-Packard Company. The information contained in this document is subject

to change without notice.

HP is a trademark of Hewlett-Packard Company.

UNIX is a registered trademark of UNIX System Laboratories Inc. in the U.S.A.

and other countries.

Hewlett-Packard Company

P.O. Box 2197

1900 Garden of the Gods Road

Colorado Springs, CO 80901-2197, U.S.A.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by the U.S.

Government is subject to restrictions set forth in subparagraph (c) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013.

Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set forth

in FAR 52.227-19(c)(1,2).

Printing History

New editions are complete revisions of the manual. The date on the title page

changes only when a new edition is published.

A software code may be printed before the date; this indicates the version level of

the software product at the time the manual was issued. Many product updates and

fixes do not require manual changes, and manual corrections may be done without

accompanying product changes. Therefore, do not expect a one-to-one

correspondence between product updates and manual revisions.

Edition 1

Edition 2

Edition 3

B3090-97000, March 1993

B3090-97001, October 1993

B3090-97002, January 1994

Safety and Certification and Warranty

Safety information, and certification and warranty information can be found on the

pages before the back cover.

iii

The HP 64783A/B Emulator

HP 64700

Instrumentation

Card Cage

HP 64783A/B

68040/EC040/LC040 Emulator

Demo Target System

HP 9000 Series 300

Host System

The HP 64783A/B Emulator

Description

The HP 64783A/B emulator supports the Motorola 68040, 68EC040, and 68LC040

microprocessors operating at clock speeds up to 33 MHz (HP 64783A) or 40 MHz

(HP 64783B). Differences between the three microprocessors are shown in the

table below:

The emulator uses an MC68040 microprocessor and is pin-for-pin compatible with

the MC68EC040 and MC68LC040 microprocessors. Refer to the end of Chapter 4,

"Using the Emulator", for special considerations when using the emulator in target

systems designed with the MC68EC040 or MC68LC040.

Throughout this manual, the microprocessor will be referred to as the MC68040,

except where the three versions must be discussed separately.

Additionally, this emulator supports development of target systems using the

MC68040 together with up to 31 MC68360’s in slave mode. Refer to the end of

Chapter 4, "Using the Emulator", for an explanation of this emulator’s support for

the MC68360 slave mode.

The emulators plug into the modular HP 64700 instrumentation card cage and offer

80 channels of processor bus analysis with the HP 64704A or HP 64794A

emulation-bus analyzer. Flexible memory configurations are offered from zero

through two megabytes of emulation memory. High performance download is

achieved through the use of a LAN or RS-422 interface. An RS-232 port and a

firmware-resident interface allow debugging of a target system at remote locations.

For software development, the HP AxCASE environment is available on SUN

SPARCsystems and HP workstations. This environment includes an ANSI standard

Motorola Processor Includes MMU Includes FPU

68040

68EC040

68LC040

yes

C compiler, assembler/linker, a debugger that uses either a software simulator or

the emulator for instruction execution, the HP Software Performance Analyzer that

allows you to optimize your product software, and the HP Branch Validator for test

suite verification.

If your software development platform is a personal computer, support is available

from several third party vendors. This capability is provided through the HP

64700’s ability to consume several industry standard output file formats.

Ada language support is provided on HP 9000 workstations by third party vendors,

such as Alsys and Verdix. An Ada application developer can use the HP emulator

and any compiler that generates HP/MRI IEEE-695 to do exhaustive, real-time

debugging in-circuit or out-of-circuit.

Features

HP 64783A/B Emulator

•16 to 33 MHz active probe emulator (HP 64783A)

•20 to 40 MHz active probe emulator (HP 64783B)

•Supports MC68040, MC68EC040, and MC68LC040

•Supports burst and synchronous bus modes

•Symbolic support

•Number of breakpoints available:

–If specified at RAM addresses: unlimited;

–If specified at ROM addresses: eight.

•36 inch cable and 219 mm (8.8") x 102 mm (4") probe, terminating in PGA

package

•Background and foreground monitors

•Simulated I/O with workstation interfaces

•Consumes IEEE-695, HP-OMF, Motorola S-Records, and Extended Tek Hex

File formats directly. (Symbols are available with IEEE-695 andHP-OMF

formats.)

•Multiprocessor emulation

–synchronous start of 32 emulation sessions

–cross triggerable from another emulator, logic analyzer, or oscilloscope

•Demo board and self test module included

Emulation-bus analyzer

•80-channel emulation-bus analyzer, which uses the static deMMUer of the

MC68040 emulator

•Postprocessed, dequeued trace with symbols

•Eight events, each consisting of address, status, and data comparators

•Events may be sequenced eight levels deep and can be used for complex

trigger qualification and selective store

Emulation memory

•256 Kbyte, 512 Kbyte, 1 Mbyte, 1.25 Mbyte and 2 Mbyte memory

configurations available

•4 Kbytes of dual-ported memory available if you use the background monitor.

•Mapping resolution is 256 bytes

•No wait states required by the emulator for processor speeds up to 25 MHz

•One wait state required in all accesses above 25 MHz

vii

In This Book

This manual covers the HP 64783A/B emulator. All information in the manual

applies to all three Microprocessor versions, unless it is marked with the processor

name (MC68040, MC68EC040, or MC68LC040).

Part 1, “Quick Start Guide,” tells you how to start using the emulator.

1. Getting Started

2. Solving Quick Start Problems

Part 2, “User’s Guide,” describes how to use the emulator/analyzer interface to

perform a variety of tasks.

3. Using the Emulator/Analyzer Interface

4. Using the Emulator

5. Using the Emulation-Bus Analyzer

6. Making Coordinated Measurements

7. Making Software Performance Measurements

8. Configuring the Emulator (to be performed before you run a program in

emulation)

9. Solving Problems

Part 3, “Reference Guide,” provides detailed information on emulator functions,

commands and environments.

10. Using MC68040 Memory Management

11. Emulator Commands

12. Emulator Messages

13. Setting X Resources

14. The SPARCsystem Interface

15. Microtec Language Tools used with the Emulator

16. Specifications and Characteristics

Part 4. "Concepts Guide," discusses X Resources and the Graphical User Interface.

Part 5, “Installation and Service Guide,” shows you how to install and maintain the

emulator.

18. Installation and Service

19. Installing/Updating Emulator Firmware

viii

Contents

Part 1 Quick Start Guide

In This Part 2

1 Getting Started

The Emulator/Analyzer Interface — At a Glance 4

The Softkey Interface 4

Softkey Interface Conventions 5

The Graphical User Interface 6

Graphical User Interface Conventions 8

The Getting Started Tutorial 11

Step 1: Start the demo 12

Step 2: Display the program in memory 14

Step 3: Run from the transfer address 15

Step 4: Step high-level source lines 16

Step 5: Display the previous mnemonic display 17

Step 6: Run until an address 18

Step 7: Display data values 19

Step 8: Display registers 20

Step 9: Step assembly-level instructions 21

Step 10: Trace the program 22

Step 11: Display memory at an address in a register 24

Step 12: Patch assembly language code 25

The MMU Demonstration 28

Step 13: Obtain the normal interface and MMU demo 29

Step 14: See the setup of the MMU 31

Step 15: Look at the translation table details for a single logical address 32

Step 16: Look at details of MMU Table C 33

Step 17: Output characters on the seven-segment display 34

Step 18: Take a trace of emulation activity 35

Step 19: Prepare the deMMUer so you can see symbolic addresses in the trace list

Step 20: Take a new trace 37

Step 21: Inverse assemble the trace list 38

Step 22: Reset the emulator 39

2 Solving Quick Start Problems

If the desired emulator interface won’t start 42

If the text-based Softkey Interface won’t start under X-Windows 42

If you can’t load the demo program 43

If you can’t display the program 44

Part 2 Using The Emulator

Making Measurements 46

In This Part 2 46

3 Using the Emulator/Analyzer Interface

Maximum Number of Windows 49

Activities that Occur in the Windows 49

Using Multiple Terminals 51

Contents

Ce manuel convient aux modèles suivants

Table des matières

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur