HP 8753D Manuel utilisateur

Printed in USA March 2000

Notice

Hewlett-Packard to Agilent Technologies Transition

This documentation supports a product that previously shipped under the Hewlett-

Packard company brand name. The brand name has now been changed to Agilent

Technologies. The two products are functionally identical, only our name has changed. The

document still includes references to Hewlett-Packard products, some of which have been

transitioned to Agilent Technologies.

User's Guide

HP 8753D Network Analyzer

ABCDE

HP Part No. 08753-90257 Supersedes October 1997

Printed in USA December 1997

Notice.

The information contained in this document is subject to change without notice

Hewlett-P

ackard makes no warranty of any kind with regard to this material, including

but not limited to, the implied warranties of merchantability and tness for aparticular

purpose

.Hewlett-P

ackard shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance

,or use of this material.



is prohibited, except as allowed under the copyright laws.

1400 Fountaingrove Parkway, Santa Rosa, CA 95403-1799, USA

Certication

Hewlett-P

ackard Company certies that this product met its published specications at the

time of shipment from the factory

. Hewlett-P

ackard further certies that its calibration

measurements are traceable to the United States National Institute of Standards and

echnology

,to the extent allowed by the Institute's calibration facility

,and

to the calibration

facilities of other International Standards Organization members.

arranty

This Hewlett-P

ackard instrument product is warranted against defects in material and

workmanship for aperiod of one year from date of shipment. During the warranty period,

Hewlett-P

ackard Company will, at its option, either repair or replace products which prove to

be defective

or warranty service or repair, this product must be returned to aservice facility designated by

Hewlett-P

ackard. Buyer shall prepay shipping charges to Hewlett-P

ackard and Hewlett-Packard

shall pay shipping charges to return the product to Buyer

.However

,Buyer shall pay all

shipping charges

,duties

,and taxes for products returned to Hewlett-P

ackard from another

country

Hewlett-P

ackard warrants that its software and rmware designated by Hewlett-P

ackard for

use with an instrument will execute its programming instructions when properly installed on

that instrument. Hewlett-P

ackard does not warrant that the operation of the instrument, or

software

,or rmware will be uninterrupted or error-free

Limit

tion of W

arranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance by Buyer

,Buyer-supplied software or interfacing, unauthorized modication or

misuse

,operation outside of the environmental specications for the product, or improper

site preparation or maintenance

NO OTHER W

ARRANTY IS EXPRESSED OR IMPLIED

. HEWLETT-P

ACKARD SPECIFICALLY

DISCLAIMS THE IMPLIED W

ARRANTIES OF MERCHANT

ABILITY AND FITNESS FOR A

ARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES.

HEWLETT-P

CKARD SHALL NOT BE LIABLE FOR ANY DIRECT

, INDIRECT

,SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL D

AMAGES, WHETHER B

ASED ON CONTRA

CT, TORT

OR ANY OTHER LEGAL THEORY

iii

Maintenance

Clean the cabinet, using a damp cloth only

Assistance

Product maintenance agreements and other customer assistance agreements are available for

Hewlett-P

ackard products

or any assistance

,contact your nearest Hewlett-P

ackard Sales and Service Oce.

2Chapter1

Contacting Agilent

By internet, phone, or fax, get assistance with all your test and measurement needs.

Table 1-1 Contacting Agilent

Online assistance: www.agilent.com/find/assist

United States

(tel) 1 800 452 4844 Latin America

(tel) (305) 269 7500

(fax) (305) 269 7599

Canada

(tel) 1 877 894 4414

(fax) (905) 282-6495

Europe

(tel) (+31) 20 547 2323

(fax) (+31) 20 547 2390

New Zealand

(tel) 0 800 738 378

(fax) (+64) 4 495 8950

Japan

(tel) (+81) 426 56 7832

(fax) (+81) 426 56 7840

Australia

(tel) 1 800 629 485

(fax) (+61) 3 9210 5947

Asia Call Center Numbers

Country Phone Number Fax Number

Singapore 1-800-375-8100 (65) 836-0252

Malaysia 1-800-828-848 1-800-801664

Philippines (632) 8426802

1-800-16510170 (PLDT

Subscriber Only)

(632) 8426809

1-800-16510288 (PLDT

Subscriber Only)

Thailand (088) 226-008 (outside Bangkok)

(662) 661-3999 (within Bangkok) (66) 1-661-3714

Hong Kong 800-930-871 (852) 2506 9233

Taiwan 0800-047-866 (886) 2 25456723

People’s Republic

of China 800-810-0189 (preferred)

10800-650-0021 10800-650-0121

India 1-600-11-2929 000-800-650-1101

Safety Symbols

The following safety symbols are used throughout this manual. F

amiliarize yourself with each

of the symbols and its meaning before operating this instrument.

Caution

Caution denotes a hazard. It calls attention to aprocedure that, if not

correctly performed or adhered to

,would result in damage to or destruction

of the instrument. Do not proceed beyond acaution note until the indicated

conditions are fully understood and met.

arning

arning denotes ahazard. It calls attention to aprocedure which, if not

correctly performed or adhered to

,could result in injury or loss of life.

Do not proceed beyond awarning note until the indicated conditions are

fully understood and met.

Instrument Markings

The instruction documentation symbol. The product is marked with this symbol when it

is necessary for the user to refer to the instructions in the documentation.

\CE" The CE mark is a registered trademark of the European Community

.(If accompanied by

ayear

,it is when the design was proven.)

\ISM1-A" This is asymbol of an Industrial Scientic and Medical Group 1Class Aproduct.

\CSA" The CSA mark is aregistered trademark of the Canadian Standards Association.

General Safety Considerations

Warning

This is a Safety Class I product (provided with a protective earthing

ground incorporated in the power cord). The mains plug shall only be

inserted in asocket outlet provided with a protective earth contact. Any

interruption of the protective conductor

, inside or outside the instrument,

is likely to make the instrument dangerous

. Intentional interruption is

prohibited.

arning

No operator serviceable parts inside

.Refer servicing to qualied

personnel. To prevent electrical shock, do not remove covers

Caution

Before switching on this instrument, make sure that the line voltage selector

switch is set to the voltage of the power supply and the correct fuse is

installed.

arning

The opening of covers or removal of parts is likely to expose dangerous

voltages

.Disconnect the instrument from all voltage sources while it is

being opened.

arning

The power cord is connected to internal capacitors that may remain live

for 10 seconds after disconnecting the plug from its power supply

arning

or continued protection against re hazard replace line fuse only with

same type and rating (F 3A/250V). The use of other fuses or material is

prohibited.

arning

If this instrument is used in amanner not specied by Hewlett-P

ackard

., the protection provided by the instrument may be impaired.

Note

This instrument has been designed and tested in accordance with IEC

Publication 348, Safety Requirements for Electronics Measuring Apparatus

,and

has been supplied in asafe condition. This instruction documentation contains

information and warnings which must be followed by the user to ensure safe

operation and to maintain the instrument in asafe condition.

vii

User's Guide Overview

Chapter 1, \HP 8753D Description and Options

," describes features

,functions, and available

options

Chapter 2, \Making Measurements

," contains step-by-step procedures for making

measurements or using particular functions

Chapter 3, \Making Mixer Measurements

," contains step-by-step procedures for making

calibrated and error-corrected mixer measurements

Chapter 4, \Printing, Plotting, and Saving Measurement Results

," contains instructions

for saving to disk or the analyzer internal memory

,andprinting and plotting displayed

measurements

Chapter 5, \Optimizing Measurement Results

," describes techniques and functions for

achieving the best measurement results

Chapter 6, \Application and Operation Concepts," contains explanatory-style information

about many applications and analyzer operation.

Chapter 7, \Specications and Measurement Uncertainties

," denes the performance

capabilities of the analyzer

Chapter 8, \Menu Maps," shows softkey menu relationships

Chapter 9, \Key Denitions

," describes all the front panel keys

,softkeys

,and their

corresponding HP-IB commands

Chapter 10, \Error Messages

," provides information for interpreting error messages

Chapter 11, \Compatible P

eripherals

," lists measurement and system accessories

,and

other applicable equipment compatible with the analyzer

.Procedures for conguring the

peripherals

,and an HP-IB programming overview are also included.

Chapter 12, \Preset State and Memory Allocation," contains adiscussion of memory

allocation, memory storage

,instrument state denitions

,and preset conditions

Appendix A, \The CITIle Data F

ormat and Key W

ord Reference

," contains information on

the CITIle data format as well as alist of CITIle keywords

viii

Network Analyzer Documentation Set

The

Installation and Quick Start Guide

familiarizes you with the network analyzer's

front and rear panels

,electrical and

environmental operating requirements

,as well

as procedures for installing, conguring, and

verifying the operation of the analyzer

The

User's Guide

shows how to make

measurements

,explains commonly-used

features

,and tells you how to get the most

performance from your analyzer

The

Quick Reference Guide

provides a

summary of selected user features

The

Programmer's Guide

provides

programming information including an HP-IB

programming and command reference as well

as programming examples

The

System V

erication and T

est Guide

provides the system verication and

performance tests and the P

erformance Test

Record for your analyzer

Autres manuels pour 8753D

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur