Hover-1 Beast Buggy Manuel utilisateur

ELECTRIC SCOOTER ACCESSORY

BEAST

BUGGY

Even if you have ridden a scooter for years, it is important for you

and every rider to read this manual before using this product.

ELECTRIC SCOOTER ACCESSORY

BEAST

BUGGY

Operation Manual HY-BST-BGY

*Images used in this manual may vary slightly from

the product and are for reference purposes only.

IMPORTANT: KEEP FOR FUTURE REFERENCE

HELMETS SAVE LIVES!

Always wear a properly tted helmet that complies with CPSC or CE safety standards

when you ride your scooter.

WARNING

Correct Fitting:

Make sure your helmet

covers your forehead.

Incorrect Fitting:

Forehead is exposed

and vulnerable to

serious injury.

This manual is designed to give you the information you need for the safe operation and maintenance of your

new Hover-1 Beast Buggy. Please read it thoroughly before riding your Hover-1 Beast Buggy.

Section One of this manual involves safety and Hover-1 Beast Buggy care. Understanding and following this

Information will help you and your Hover-1 Beast Buggy avoid injury or damage.

Section Two of this manual gives assembly and installation instructions for your Hover-1 Beast Buggy.

Section Three of this manual covers specic safety and operating instructions for your Hover-1 Beast Buggy.

Even if you are an experienced rider, you should review this section before your rst ride.

Section Four of this manual covers warranty specications of your Hover-1 Beast Buggy.

INTRODUCTION

WARNING

Make sure you read this complete manual before riding

your Hover-1 Beast Buggy. Failure to do so, or failure to

follow its guidelines could lead to serious injury or death.

HOVER-1 BEAST BUGGY DIAGRAM

SPECIFICATIONS

1. Seat

2. Handle Bars

3. Shock Absorbing Coils

4. Pedal Mounts

5. Hook and Loop Elastic Strap

6. Seat Frame

7. Locker

8. Frame Extension

9. Foot Rests

10. Caster Wheel

Compatibility: Most self-balancing electric scooters with 10” wheels

Max Load: See max load of your self-balancing scooter

Max Speed: See max speed of your self-balancing scooter

Tire Size: 8” swivel caster

Seat Material: PP

PARTS LIST

(1) Seat

(1) Seat Frame

(1) Frame Extension

(1) Left Handle Bar

(1) Caster Wheel

(1) Right Handle Bar

(6) Hook and Loop

Elastic Strap

(1) Wrench

(4) Small Foam Pad

(1) Allen Wrench Set

(2) Locker

(6) Large Screws

(4) Small Screws

(6) 8mm Nut

(6) Large Washers

ASSEMBLING YOUR HOVER-1 BEAST BUGGY

If you have questions or concerns about any of these steps, please feel free to contact our Customer Service

Team at www.hover-1.com. Someone will be in touch to walk you through these steps.

Carefully follow the steps shown on the following pages for assembling the Hover-1 Beast Buggy.

Remove all Hover-1 Beast Buggy contents from the box. Ensure all contents from the “Parts List” section are

accounted for.

1. Using the two large screws and washers, attach the handle bars to the appropriate sides of the seat frame as

shown below. Tighten with included Allen wrench.

2. Align the caster wheel to the screw holes in front of the frame extension. Secure the caster wheel in place using

the included Allen wrench, four large screws, four large washers and four nuts.

4. Attach the lockers onto the the seat frame and insert the frame extension into the seat frame. Adjust the frame

extention to preferred length. Secure the frame extension in place using the two lockers. You can tighten the

lockers if needed by adjusting the bolt.

locker

Adjust bolt to tighten/loosen

lockers if needed

3. Align the holes of the seat with the seat frame.

Secure the seat in place using the included Allen

wrench and four small screws.

4. Your Hover-1 Beast Buggy is now

completely assembled and should look

like the below image.

If you have questions or concerns about any of these steps, please feel free to contact our Customer Service

Team at www.hover-1.com. Someone will be in touch to walk you through these steps.

Carefully follow the steps shown on the following pages for installing the Hover-1 Beast Buggy onto your

electric scooter. Read the remainder of this manual before riding your Hover-1 Beast Buggy.

Your Hover-1 Beast Buggy should be completely assembled prior to installing it onto your electric scooter.

Please refer to the “Assembling your Hover-1 Beast Buggy” section for assembling procedures.

1. Place the pedal mounts onto the foot pedals of your self-balancing scooter with the front wheel facing

forward. Ensure the pedal mounts are centered on the foot pedals of your scooter as much as possible.

INSTALLING YOUR HOVER-1 BEAST BUGGY

SPACE EVENLY

Autres manuels pour Beast Buggy

Table des matières

Autres manuels Hover-1 Scooter

Hover-1

Hover-1 H1-MFEB Manuel utilisateur

Hover-1

Hover-1 HY-H1 Manuel utilisateur

Hover-1

Hover-1 ESCAPE Manuel utilisateur

Hover-1

Hover-1 Journey H1-JNY Manuel utilisateur

Hover-1

Hover-1 EDGE 2.0 Manuel utilisateur

Hover-1

Hover-1 DREAM Manuel utilisateur

Hover-1

Hover-1 NOVA Manuel utilisateur

Hover-1

Hover-1 HELIOS Manuel utilisateur

Hover-1

Hover-1 H1 Manuel utilisateur

Hover-1

Hover-1 JOURNEY Manuel utilisateur

Hover-1

Hover-1 RIDER Manuel utilisateur

Hover-1

Hover-1 Go-Kart Manuel utilisateur

Hover-1

Hover-1 H1-ACE4 PRO ACE R450 Manuel utilisateur

Hover-1

Hover-1 Pro Series ACE R450 Manuel utilisateur

Hover-1

Hover-1 INSTINCT H1-EGBR Manuel utilisateur

Hover-1

Hover-1 Liberty Manuel utilisateur

Hover-1

Hover-1 HORIZON HY-H2L Manuel utilisateur

Hover-1

Hover-1 MY FIRST E-SCOOTER Manuel utilisateur

Hover-1

Hover-1 TURBO Manuel utilisateur

Hover-1

Hover-1 FLEX Manuel utilisateur

Hover-1

Hover-1 RENEGADE Manuel utilisateur

Hover-1

Hover-1 ALPHA-PRO Manuel utilisateur

Hover-1

Hover-1 FADE Manuel utilisateur

Hover-1

Hover-1 Pro Series ACE R350 Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur