Hotpoint HDI90X Manuel utilisateur

Instructions for Installation and Use

Electric Hood

Model HDI90X

GB 2

CONTENTS

RECOMMENDATIONS AND SUGGESTIONS 3

INSTALLATION 4 - 9

ELECTRICAL CONNECTION 10

GETTING TO KNOW YOUR COOKER HOOD 11

CARE AND CLEANING 12

AFTER SALES SERVICE 14

GUARANTEE 15

KEY CONTACTS Back Cover

Retention of this Instruction Book

This Instruction Book must be kept handy for reference as it contains important details on the safe and proper use

of the appliance.

If you sell or pass the appliance to someone else, or move house and leave it behind, make sure this Book is

also provided so the new owner can become familiar with the appliance and safety warnings.

If the Book is lost or damaged a copy may be obtained from:

GDA LTD., Morley Way, Peterborough, PE2 9JB

CE marking certifies that this appliance conforms to the

following EEC directives:-

-Low Voltage Equipment 72/23/EEC

-Electromagnetic Compatibility 89/336/EEC

3GB

RECOMMENDATIONS AND SUGGESTIONS

Using your new Cooker Hood is very simple. Nevertheless, to get the best results it is important

that you read this manual thoroughly before installing and using your appliance for the first time.

INSTALLATION

• All installation and repairs should be carried out by a qualified

technician in accordance to regulations in force.

• The manufacturer will not be held liable for any damage resulting

from incorrect or improper installation.

• After having removed the packaging, check the condition of the

appliance, if in any doubt, do not use and contact Hotpoint Service

(see Key Contacts, back page).

• The minimum safety distance between the hob and the extractor

hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of ventilation

must be guaranteed in the room in order to prevent the backflow of

exhaust gas. The kitchen must have a suitable vent to the outside

of the building, so that clear fresh air can circulate through the

kitchen.

USE

• The extractor hood has been designed exclusively for domestic use

to eliminate kitchen smells.

• Never use the hood for purposes other than for which it has been

designed.

• Never leave high naked flames under the hood when it is in

operation.

• Adjust the flame intensity to direct it onto the bottom of the pan

only, making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use:

overheated oil can burst into flames.

• When frying, never leave the pan unattended.

• The hood should not be used by children or persons not instructed

in its correct use.

MAINTENANCE

• Switch off and unplug the appliance from the mains supply before

carrying out any cleaning or maintenance work.

• Clean regularly (see Care and Cleaning section), build up of dirt

and grease could cause a fire hazard.

4GB

INSTALLATION

Dimensions

5GB

INSTALLATION

Components

Ref. Qty Product Components

11 Hood Body, complete with: Controls, Light,

Blower, Filters

21 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with extractor,

consisting of:

7.1a 1 Upper Frame

7.1b 1 Lower Frame

8a 1 Right Air Outlet Grill

8b 1 Left Air Outlet Grill

91 Reducer Flange ø 150-120 mm

14 1 Hood Body Air Outlet Extension Piece

consisting of two half shells

14.1 1 Air Outlet Connection Extension

15 1 Air Outlet Connection

24 1 Junction box

25 2 Pipe clamps

26 1 Fixing part of the upper chimney

Ref Qty Installation Components

11 4 Wall Plugs ø 10

12c 6 Screws 2.9 x 9.5

12e 2 Screws 2.9 x 6.5

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5.2 x 70

12w 2 Screws M3 x 8

21 1 Drilling Template

22 4 6.4mm int. dia washers

23 4 M6 nuts

Qty Documentation

1 Instruction Manual

6GB

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING / SUPPORT SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template

is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20mm: drill ø 10mm.

• For wooden beam ceilings, drill according to the wood screws to be used.

• For wooden shelf, drill ø 7mm.

• For the power supply cable feed, drill ø 10mm.

• For the air outlet (Ducted version), drill according to the diameter of the external air exhaust

duct connection.

7GB

INSTALLATION

FIXING THE FRAME

Before fixing, seperate the Upper section 2.1 and

the Lower section 2.2 from the frame by unscrewing

the screws 12c. Then seperate the two sections of

the frame (Upper and Lower) by unscrewing the 8

side screws.

Fix the Fixing Part of the Upper Chimney 26 to the

hanging kit using the 2 screws 12w (M3 x 8).

Upper Frame

• Align the power supply cable feed hole.

• Fix the upper frame to the ceiling of shelf using:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• For hollow brick ceilings of wall thickness of approximately 20mm: use 4 plugs 11 and 4

screws 12h (5.2 x 70), provided.

• For wooden beam ceilings, use 4 wood srews (not provided).

• For wooden shelf, use 4 screws 12g (M6 x 80) with washers 22 and nuts 23, provided.

Lower Frame

• Fix the lower frame using the 8 previously removed screws, adjusting the length according to the

installation height (hood body lower fixing surface must be at least 710mm from the hob).

• For the recirculation version, turn the frame in the direction chosen for the recirculated air outlet.

• The frame mounting must be secure to withstand the weight of the hood and any stresses caused

by the occassional side thrust applied to the device. On completion, check that the base is stable,

even if the frame is subjected to bending.

• In all cases where the ceiling is not strong enough at the suspension point, the installer must

provide strengthening, using suitable plates and backing pieces anchored to the structurally sound

parts.

8GB

INSTALLATION

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the

hood to the chimney using either a flexible or

rigid pipe ø 150 or 120 mm, the choice of which

is left to the installer.

• To install a ø 120 mm air exhaust connection,

insert the reducer flange 9on the hood body

outlet.

• Fix the pipe in position using the pipe clamps

25 provided.

• Remove any activated charcoal filters.

RECIRCULATION VERSION AIR OUTLET

• Push the connection 15 onto the air outlet.

• Insert the connection extension pieces laterally

14 in connection 15.

• Place the upper chimney section and fix the

upper part to the Fixing Part of the Upper

Chimney using the 2 screws 12c (2.9 x 9.5)

provided.

• Similarly, position the lower chimney section

and fix the lower part to the frame using the 2

screws 12c (2.9 x 9.5) provided.

Recirculation version

• Make sure that the outlet of the extension pieces

14.1 is horizontally and vertically aligned with

the chimney outlets.

• If this is not the case, remove the lower chimney

section and adjust the position by either

reversing the connection pieces 14.1 or by cutting

the hood body extension 14 along one of the

thinner section channels denoting the pre-fixed

lengths, then reassemble as described previously.

• Fit the directional grids 8a-8b in their housings

making sure that the directional symbols are

towards the top. Also make sure that they are

correctly inserted in the connection extension

pieces 14.1.

9GB

INSTALLATION

Connections

Before fixing the hood body to the frame:

• Remove the grease filters from the hood body.

• Remove any activated charcoal filters.

• From below, use the 4 screws 12f (M6 x 10)

provided, to fix the hood body to the frame.

• Fix the Lower Chimney to the Hood Canopy

using the 2 screws 12c (2.9 x 9.5) provided.

ELECTRICAL CONNECTIONS

WARNING -

THIS APPLIANCE MUST BE EARTHED

This appliance must be connected by a competent

person eg. NICEIC registered contractor, in

accordance with latest IEE regulations.

The appliance is supplied with a fitted plug. If the

appliance is to be connected to fixed wiring, it

must be connected to a double-pole control unit

with a minimum switch rating of 5A and

protected by a 3A fuse.

• Connect the hood to the mains through a double

pole switch having a contact gap of at least 3mm.

• Connect the control connector Cmd.

• Place the connector in the junction box 24 and

close it using the 2 screws 12e (2.9 x 6.5)

provided.

• Fix the junction box to the hood body using the

2 screws 12c (2.9 x 9.5) provided.

• For the recirculation version, fit the activated

charcoal filter.

• Replace the grease filters.

10GB

Electrical Connection

WARNING: This appliance MUST be earthed. Connect to a 230 - 240V A.C. Supply only.

• Connection to the electricity supply should be made via a properly earthed, readily accessible

wall socket which is adjacent to and not more than 1.25m away from the appliance and capable of

electrical isolation.

Should this plug not fit the socket outlet in your home it should be cut off and replaced with a

suitable plug as outlined below.

Note: The removed plug cannot be used for any other appliance and should therefore be properly

disposed of and not left where children might find it and plug it into a supply socket - with the

obvious consequent danger.

IF THE FITTED PLUG IS REMOVED

The flexible mains lead must be correctly connected as below, to a three pin plug of not less than 13

amp capacity. If a B.S.1363 fused plug is used, it must be fitted with a 3amp fuse which is approved

to B.S.1362.

IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with

the following code:

GREEN and YELLOW - EARTH

BLUE - NEUTRAL BROWN - LIVE

CORD CLAMP 3amp FUSE

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:- The wire which is green and

yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth

symbol or coloured green or green and yellow. The wire which is coloured blue must be connected

to the terminal which is marked with the N or coloured black. The wire which is coloured brown

must be connected to the terminal which is marked with the letter L or coloured red. When wiring the

plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the

mains lead clamp on the plug. As the appliance must be earthed, DO NOT use 2-pin socket outlets,

if you are in doubt, consult a qualified electrician.

Should the mains lead ever require replacement, it is essential that this operation be carried out by a

qualified electrician and should only be replaced with a flexible cord of the same size ie. 0.75mm2

cross sectional area and temperature rating of 85°C eg. heat resisting PVC.

IF A MOULDED PLUG IS FITTED

In the event of replacing a fuse in the plug supplied a 3amp ASTA approved fuse to B.S.1362 must

be fitted.

Note: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover

the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse

cover can be obtained from your local Electrical Retailer. The colour of the correct replacement fuse

cover is that of the coloured marks or inserts in the base of the plug.

Table des matières

Autres manuels Hotpoint hotte de ventilation

Hotpoint

Hotpoint CANNON BCH100 Manuel du propriétaire

Hotpoint

Hotpoint kitchen think HSD92 Manuel utilisateur

Hotpoint

Hotpoint HXQB 9.8LTI Manuel utilisateur

Hotpoint

Hotpoint HXC6 8ATI Series Manuel utilisateur

Hotpoint

Hotpoint PSLCSE 65F AS X Manuel utilisateur

Hotpoint

Hotpoint PHBS6.7FLLIX Manuel utilisateur

Hotpoint

Hotpoint HLB 9.5S AT(ICE)/HA Manuel utilisateur

Hotpoint

Hotpoint PHBS 9.8C LTD K Manuel utilisateur

Hotpoint

Hotpoint HL60X Manuel utilisateur

Hotpoint

Hotpoint Creda LI2I3A Manuel utilisateur

Hotpoint

Hotpoint PHBS 9.8C LTD K Manuel utilisateur

Hotpoint

Hotpoint HXB 9 LS X Manuel utilisateur

Hotpoint

Hotpoint HD 6 Manuel utilisateur

Hotpoint

Hotpoint kitchen think HTC92X Manuel utilisateur

Hotpoint

Hotpoint PHPN6.5 FLMX Manuel utilisateur

Hotpoint

Hotpoint kitchen think HE62 Instructions for Mode d’emploi

Hotpoint

Hotpoint kitchen think HD70X Instructions for and... Manuel utilisateur

Hotpoint

Hotpoint HXB6X Manuel utilisateur

Hotpoint

Hotpoint HS9EIX Manuel utilisateur

Hotpoint

Hotpoint HSFX.1 Instructions d'utilisation et d'installation

Hotpoint

Hotpoint HDI 93 X Manuel utilisateur

Hotpoint

Hotpoint PSLMO 65F LS X Manuel utilisateur

Hotpoint

Hotpoint HXV9K Manuel utilisateur

Hotpoint

Hotpoint HS 110 Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur