HORNER WWPC40 Manuel utilisateur

LMAN0052-01-EN

59 South State Ave., Indianapolis, IN 46201 | (p) 317.916.4274 (tf) 877.665.5666 (f) 317.639.4279 | www.hornerlighting.com

Product Description

The Wall Pack series lights are the latest innovation from

Horner Lighting providing high output, while saving energy.

There are two models of Wall Packs: WWP and WWPC, both

coming in 40W and 60W options.

Precautions

WARNINGS

Risk of electrical shock. Disconnect power before servicing or

installing product.

Risque de choc électrique. Coupez l’alimentation avant

l’entretien ou l’installation du produit.

Risk of injury or damage. Unit will fall if not installed properly.

Follow installation instructions.

Risque de blessures ou de dommages. Unité va tomber s’il n’est

pas installé correctement. Suivez les instructions d’installation.

Risk of injury. Wear safety glasses and gloves during installation

and servicing.

Risque de blessure. Porter des lunettes de sécurité et des gants

lors de l’installation et de l’entretien.

Risk of injury or damage. LED light sources achieve full intensity

immediately after powered. Do not look directly the lights.

Risque de blessures ou de dommages. Sources de lumière LED

parvenir à pleine intensité immédiatement après sous tension. Ne

regardez pas directement la lumière.

WALL PACK INSTALLATION GUIDE

Unit Installation

This guide is meant to be used for both the WWP and WWPC

models. Unpack the unit and check for any shipping damage.

NOTE: Wall Packs must match the input voltage to the supply

voltage. Please confirm the product voltage and supply

voltage match before installation.

WWPC40/

WWPC60

WWP40/

WWP60

Wall Pack Series Base

WWPC40/

WWPC60

WWP40/

WWP60

LMAN0052-01-EN

59 South State Ave., Indianapolis, IN 46201 | (p) 317.916.4274 (tf) 877.665.5666 (f) 317.639.4279 | www.hornerlighting.com

Cleaning

To maintain efficiency, the glass lens should be cleaned with

a mild soap or neutral PH cleaner.

Abrasives or cleaners containing chlorinated or aromatic hy-

drocarbons should not be used. Once clean, rinse with cold

water and wipe dry with a soft cloth.

Fixture Mounting

Mount the light base to the building using proper anchors for the building material. You may need to add additional support

behind the surface material.

Wiring

Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements.

Remove screw and lid to power

supply.

Attach ground to connector.

Bring incoming AC through opening.Open back of unit housing to access

power supply.

Attach line and neutral. Use diagram

on power supply.

Replace power supply lid and screw.

Technical Support

Tel: 317-916-4274

Fax: 317-639-4279

Email: techsppt@HornerETG.com

Web: http://www.hornerlighting.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HORNER Éclairage extérieur

HORNER

HORNER ETG-A100A Manuel utilisateur

Manuels Éclairage extérieur populaires d'autres marques

Sealey

Sealey LED37 Manuel utilisateur

nordlux

nordlux VEJERS Guide de l'utilisateur

SImx

SImx ELITE LED LHTC637 Manuel utilisateur

GEV

GEV CAROLINE 10833 Manuel utilisateur

NEBO

NEBO NEB-LSP-0020 Manuel utilisateur

WE-EF

WE-EF PFL540 LED Manuel utilisateur

Lindby

Lindby 9949029 Manuel utilisateur

HEPER

HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation

HEPER

HEPER LW8034.003-US Instructions d'installation et d'utilisation

Maretti

Maretti VIBE S 14.6080.04.A Manuel utilisateur

BEGA

BEGA 84 253 Manuel

HEPER

HEPER MINIMO Instructions d'installation et d'utilisation

LIGMAN

LIGMAN BAMBOO 3 Manuel utilisateur

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur

urban ambiance

urban ambiance UQL1273 Manuel utilisateur

TotalPond

TotalPond 52238 Manuel utilisateur

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuel utilisateur