Honeywell HBT083P Manuel utilisateur
CSHBT083PV1 12/04 Rev.A
HBT083P/MDT083P
HBT083P/MDT083PHBT083P/MDT083P
HBT083P/MDT083P
KSU/PBX Telephone
KSU/PBX TelephoneKSU/PBX Telephone
KSU/PBX Telephone
Distribution Hub/Module
Distribution Hub/ModuleDistribution Hub/Module
Distribution Hub/Module
INSTALLATION GUIDE
Description
The HBT083P and MDT083P Hub and Module provide distribution of four (4) incoming telephone lines to eight
(8) locations via 110 connectors, and One (1) video signal to eight (8) locations. The Hub/Module also includes
a 12dB amplifier and two (2) coax pass through connections for Satellite TV. This Module will requires 6-inches
of space in a QuickNetwork rough-in can.
Features
• Twelve ports
• Four line capability
• RJ31x port
• Labeling space for every port
Important Warnings
♦ Never install or work with telephone wiring during a lightning storm.
♦ Never install telephone jacks in wet locations unless the jack is specifically designed for use in wet locations.
♦ Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
the network interface.
♦ Use caution when installing or modifying telephone lines.
♦ Have the Electrician connect the AC outlet to branch circuit power. The connection should be in accordance
with the National Electrical Code, Articles 110, 250 and 300.
Installing the Distribution Hub/Module
Connect the service input cable to the center F-type
coax port on the module labeled “CATV/ANT IN”. These
signals can be either Cable TV, Antenna or a modulated
video signal. Connect a coax cable between the “12 V
DC IN” port and the provided DC power module. Once
the input and power cables have been connected the
video signal will be distributed the video signal to all of
the outputs on the module. There are also two Pass
through Aux. ports that can be use to pass satellite
signals.
Connecting TV outlets to outputs
1. Remove the silver terminating caps ONLY from the
ports that will be connected to outlet cables.
Keeping the caps on unused port, will help prevent
unwanted video signals from entering your TV
system.
2. Connect the outlet cables to the module.
3. Connect the incoming cables from the Satellite TV to
the pass-through F connectors on the rear of the
module.
4. Connect the outgoing satellite cables between the
receiver and the front side of the module.
Connecting Telephone Service
Connecting Incoming Phone Lines
1. Trim back the PVC jacket on the incoming phone
cable approximately ¾-inch (be sure to re-label if
necessary) allowing for a bend radius of at least
four times the diameter of the CAT5 telephone
cable.
2. Separate the pairs from each other but do not
untwist the pairs. Be sure to label each
connection on the provided documentation
template painted on the face of the module.
Note: Do not untwist the conductors more than ½-inch from
the point of termination.
3. Following the 568A color code that is printed on
the 110 connectors, punch down the incoming
cables on the module’s 110 connectors. Start with
the blue pair punch the cable down into the slots.
4. Punch down all the Cat5e cables in the same
fashion, positioning and trimming each in order to
maintain neatness.
Note: Make sure that the Tip and Ring are properly
connected to the 110 punch down. In most cases the
blue/white is first and then the white/blue.
5. Once the remaining cables have been connected
(up to four lines) the incoming phone lines will be
distributed to the outlet ports on the top side of
the module.
Connecting outgoing telephone cables
The outgoing RJ45 ports will accept cables with either
RJ45 or RJ11 connectors. RJ45 termination is
recommended so that the four line capability can be
used. When terminating the cables follow the 568A
standard.
If a MDP3 patch module is being installed, connect a
patch cord between the telephone outputs and the
zones on the MDP3 patch module.
Connecting the module to a Security System
After phone service has been connected to the
module, route a CAT5 patch cord between the RJ31x
port and the security system. Cut the RJ45 connector
off at the Security system end and use the following
diagram to connect the phone service to the security
system and to the module.
‡CSHBT083PV1aŠ
CSHBT083PV1 12/04 Rev. A
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Honeywell Changer
Honeywell
Honeywell Limitless WGLA Series Manuel utilisateur
Honeywell
Honeywell LOSCDT1000RWH Manuel utilisateur
Honeywell
Honeywell B Manuel d'utilisation
Honeywell
Honeywell MAXPRO-Net Instructions de montage
Honeywell
Honeywell 39342 Manuel utilisateur
Honeywell
Honeywell 39346 Manuel utilisateur
Honeywell
Honeywell PK 81590 Manuel utilisateur
Honeywell
Honeywell VC Series Manuel utilisateur
Honeywell
Honeywell 10260 Series Manuel utilisateur
Honeywell
Honeywell OP-AR Manuel utilisateur
Honeywell
Honeywell C6097B Manuel utilisateur
Honeywell
Honeywell Krom Schroder DG H Series Manuel utilisateur
Honeywell
Honeywell RPLS740B Manuel utilisateur
Honeywell
Honeywell 10260A Series Manuel utilisateur
Honeywell
Honeywell CSS-O-A300-001 Manuel utilisateur
Honeywell
Honeywell DDS76-1/2 Manuel utilisateur
Honeywell
Honeywell PLS530A Manuel utilisateur
Honeywell
Honeywell PLS731B Manuel utilisateur
Honeywell
Honeywell PEHA PHC Guide de l'utilisateur
Honeywell
Honeywell MICRO SWITCH BX2 Series Manuel utilisateur
