Honeywell V4000 Instructions de montage

K14020 6/05 Rev. A

Installation and Setup Guide

Installation and Setup GuideInstallation and Setup Guide

Installation and Setup Guide

Table of Contents

Introduction .........................................................................................................................5

Basic Operation ...............................................................................................................5

Remote Look In ...............................................................................................................5

Features:...........................................................................................................................5

Specifications: .................................................................................................................6

Installing the V4000 ............................................................................................................7

Mounting .........................................................................................................................7

Wiring..............................................................................................................................7

Programming the Control Panel ..........................................................................................9

Setup Considerations .......................................................................................................9

Control Center Software Installation...................................................................................9

Minimum System Requirements .....................................................................................9

Recommended System Requirements ...........................................................................10

Software Installation..........................................................................................................10

Setting Screen Resolution and Color Palette.....................................................................10

Initial Control Center Operation........................................................................................11

Entering and Connecting to a New Site.............................................................................11

System Checkout ...............................................................................................................11

Troubleshooting.................................................................................................................12

Appendix A: Direct Connection to PC/Laptop Computer.................................................12

Appendix B: Pan, Tilt & Zoom .........................................................................................13

FCC COMPLIANCE STATEMENT................................................................................14

LIMITED WARRANTY...................................................................................................16

This manual contains information on limitations regarding product use and

functionality, as well as the limitations regarding liability of the manufacturer.

Please read the entire manual carefully.

Introduction

The V4000 captures and stores video images (ME-JPEG’s) for transmission to a central

station for visual verification of alarms. Images are transmitted over standard telephone

lines using an internal modem. The capture of images is initiated by a zone violation in

an associated control panel. Specialized Control Center Software allows the user

configuration options including pre-trigger/post-trigger on alarm, frame capture rate, and

image resolution. Refer to the Control Center Software User Guide for additional

details.

Basic Operation

Video information from the 4 video inputs is initially formatted into an ME-JPEG format

and stored in an on-board buffer. Subsequent video captures store only the difference

data required to assemble the frames captured. When the buffer is full, the data is

continuously updated by writing the new data over the old data. This process ensures

that a recent history is maintained in memory before an alarm event occurs. The buffer

allocated to on-going storage is programmable using Control Center Software. When

an alarm event occurs, the control panel calls the central station to report the alarm and

then signals the V4000 via the control panel’s keypad (ECP) bus. The remaining video

buffer memory is used to capture the event. When the remaining memory is filled,

recording of video events ceases. After the central station call is completed, the V4000

takes control of the phone line and calls a previously stored number for the central

station that will process the video signal. The completed video clip including the pre-

alarm video and the post-alarm video is transmitted to the central station using the

internal modem.

Note: Central Station calling and transmission of video by the V4000 is independent of

the control panel. If a subsequent alarm event occurs during video transmission,

the transmission will be terminated and the control panel will seize the phone

line to forward the alarm information to the central station. When the call is

completed the V4000 will resume its call to the central station and transfer the

video data. Contact your central station to confirm support for OzVision™ video

transmission protocol.

Remote Look In

Video data can also be retrieved by accessing the module via telephone with a PC

using Control Center Software and utilizing the module in a streaming video

mode.

Features:

• 4 baseband video inputs (NTSC & PAL compatible)

• PSTN (telephone) connection - Tip, Ring

• Interface to Honeywell Ademco control panels via the panel’s keypad (ECP) bus.

• Status LEDs

• Green - Power On indicator

• Red - Flashes during self test

• Standard RS232 serial port for Euro ISDN connection, PC, Cellular modem

• Pan/Tilt/Zoom (PTZ) - supports ERNA, VCLTP, Ultrack, Migvan, EscBaz and

DynaColor protocols.

• On board modem

Specifications:

Voltage:12 to 17VDC

Current Draw:

Standby: 370 mA

Transmitting: 490 mA Max.

ECP Bus: 45mA

Operating Temperature Range:

32°to 131°F (0°- 50°C)

Humidity:

25 to 80% Non Condensing

Resolution:

128h x 100v NTSC or PAL

256h x 100v NTSC or PAL

256h x 200v NTSC or PAL

512h x 200v NTSC or PAL

Color Resolution:

16.8 million colors with 256 gray scales.

On-board Frame Storage:

200 Kbytes.

Installing the V4000

Mounting

1. Mount the V4000 unit (on its mounting plate) to the control panel cabinet as

shown. Screw the bottom of the mounting plate into the enclosure (using the

lower mounting holes) using the screws provided (see Figure 1).

2. Install two AD12612 Power Supplies in the cabinet as shown, using the double-

sided tape provided. (One will be used to power the module, and the other to

power the cameras.)

Figure 1: Mounting the V4000 and Power Supplies

Wiring

Once all components are mounted, wire the unit as follows, referring to Figure 2.

1. Connect Handset side Tip and Ring on the Control panel to the V4000 Tip and

Ring terminals as shown in Figure 2.

Note: Ensure that all plugs and jacks meet the dimension, tolerance and plating

requirements of 47 C.F.R. Part 68, Subpart F. For proper operation there must

not be any additional equipment connected between the control panel and the

telephone company facilities (e.g., fax machines).

2. Connect the video cables from the CCTV cameras to the BNC connectors.

Notes: ✓

✓✓

✓The DIP switches on the V4000 are set for direct connection of CCTV

cameras to the unit (down). If the CCTV cameras are connected in parallel

to other devices (e.g. VCR/Monitors), set the associated DIP switch to the

UP position to ensure correct termination.

✓

✓✓

✓The DIP switches on the interface board are not used.

3. Ensure that the designated trigger zones on the control panel are installed

4. Connect the Keybus terminals of the V4000 module to the control panel’s keypad

(ECP) bus using 22AWG (5mm), quad, twisted two-pair wire.

5. Connect an ADEMCO AD12612, 12VDC, 1A power supply to the Power In

terminals on the V4000.

Caution: Ensure that the correct polarity is observed when connecting to the

power source.

Caution: Ensure that the negative power input, negative power output, circuit

common, and unit chassis are tied together in the V4000 Video Module.

6. Power-up the system.

Figure 2: System Wiring

Programming the Control Panel

Setup Considerations

Cameras connected to the V4000 can be triggered by system events from a Honeywell

Vista control panel.

The cameras are turned on using Output (relay) Programming commands in the

control panel, although no relay module is actually used. To accomplish this, do the

following:

1. Enable a 4204 Relay Module in the system’s Device Programming Mode as

Device Address 12.

2. Program up to four logical relays to be triggered by different alarm conditions

you would like to turn cameras on with, and program each to “pulse for 2

seconds”when triggered. Cameras are turned on through the ECP (Data In

and Data Out) connections (see the control panel’s Programming Guide for

information on how to program output relays).

3. Program Relay 4 to trip upon “kissoff”of the control panel’s message to the

central station. This relay will cause the V4000 to call the central station

number programmed inside of it and transmit the video information of the

triggered output’s camera.

IMPORTANT: If four actual cameras are desired, one of the first three relays

must be programmed to trigger on two different events (two “logical”outputs

which point to the same “physical”relay must be programmed). One of those

outputs must be programmed to “continuous pulse”when it turns on, so that

the V4000 can differentiate between the messages. See the example below.

4204 Output Command (4204 on ECP Address 12) Function

Relay 1: Turn ON for 2 seconds when zone 1 goes into alarm Captures Video on Camera 1

Relay 2: Turn ON for 2 seconds when zone 4 goes into alarm Captures Video on Camera 2

Relay 3: Turn ON for 2 seconds when system is disarmed Captures Video on Camera 3

Relay 1: Continuous Pulse when zone 8 goes into alarm Captures Video on Camera 4

Relay 4: Turn ON for 2 seconds upon kissoff from central station Causes V4000 to dial out to video central

station

Notes: The linking of outputs to specific cameras is performed by Control Center

Software’.

Only conditions that cause a central station report to be sent can be used to

trigger camera transmissions (e.g., alarms).

Control Center Software Installation

Minimum System Requirements

•CPU: Intel Pentium III 800 MHZ or higher processor.

•Memory: 128MB of RAM

•Free Space: 5MB of available hard disk space.

•Modem: 33.6/56K

•Operating System: Windows 98/ME/2000 professional/ NT4/XP.

•Minimum screen resolution: 800X600, 24 true-bit colors

Recommended System Requirements

•CPU: Intel Pentium IV 1.6 GHZ .

•Memory: 128MB of RAM

•Free Space: 5MB of available hard disk space.

•Modem: 33.6/56K

•Operating System: Windows ME/2000 professional/ NT4/XP.

•Minimum screen resolution: 800X600, 24 true-bit colors

Intel and Pentium are registered trademarks of Intel Inc.

Windows is a registered trademark of the Microsoft Corporation

Software Installation

Insert the Control Center Software CD and perform the steps indicated in the Installation

Wizard, or:

1. Click the Start button at the bottom left corner of the windows screen.

2. Select Settings > Control Panel > Add/Remove Programs from the menu.

3. Click Install to begin the installation.

4. Insert the Control Center CD in the CD drive.

5. Click Next. The Windows installation program searches the disc for the Control

Center installation program and displays it in the ‘Command line for

installation program’edit box.

6. Click End.

7. When the Control Center installation screen appears, select Next.

8. The Choose Destination Location window will appear. This screen will

determine the directory in which Control Center Software is installed.

Honeywell recommends installation in the default directory. After the

destination folder has been chosen, click Next to continue.

9. Repeat Step 8 for the location of the data files.

10. After copying all files to your computer, the Select Components screen will

appear. Two check boxes will be displayed:

•Select Create a Shortcut to create a shortcut on your desktop.

•Select Run Control Center Automatically upon Startup if you want

Control Center to load on startup.

11. Click on Next to continue the installation. An Information screen will appear

confirming a successful installation.

12. Click Finish.

Setting Screen Resolution and Color Palette

1. Right-click on an empty spot on the desktop (the Windows™background).

2. Select Properties from the menu. The Display Properties screen will appear.

3. Select Settings (located at the top right of the screen).

4. Set the display area to 800 x 600 or higher.

5. Set Color Palette to 24 bit True Color.

6. Set Font Size to Large Fonts.

7. Click OK to confirm the new settings.

8. Restart the computer to activate settings if required.

Autres manuels pour V4000

Table des matières

Autres manuels Honeywell Système de sécurité

Honeywell

Honeywell ADEMCO 6150V Manuel utilisateur

Honeywell

Honeywell INTELLIGUARD 9000 Manuel utilisateur

Honeywell

Honeywell Ademco VISTA-50P Mode d'emploi

Honeywell

Honeywell LYNX Touch 5100 Mode d'emploi

Honeywell

Honeywell SF340F Manuel utilisateur

Honeywell

Honeywell L5200 Series Manuel utilisateur

Honeywell

Honeywell Friedland HISK1 Manuel utilisateur

Honeywell

Honeywell Lyric SIXSIREN Manuel utilisateur

Honeywell

Honeywell HS-6270 Manuel utilisateur

Honeywell

Honeywell Galaxy 2-44+ Manuel utilisateur

Honeywell

Honeywell LYNX Touch Security System Manuel utilisateur

Honeywell

Honeywell LYNX Touch L7000 Series Manuel utilisateur

Honeywell

Honeywell Code Encryptor II Manuel utilisateur

Honeywell

Honeywell Ademco VISTA-20P Manuel utilisateur

Honeywell

Honeywell HS923GPRS Manuel utilisateur

Honeywell

Honeywell ADEMCO Vista-12C Instructions de montage

Honeywell

Honeywell VISTA-32FBPT Instructions de montage

Honeywell

Honeywell VISTA-128BPTSIA Manuel utilisateur

Honeywell

Honeywell Water Defense RWD41 Manuel utilisateur

Honeywell

Honeywell LYNX Touch Security System Manuel utilisateur

Honeywell

Honeywell FBII OMNI 600 Manuel utilisateur

Honeywell

Honeywell Le Sucre Manuel utilisateur

Honeywell

Honeywell nfs2-3030 Manuel utilisateur

Honeywell

Honeywell Code Encryptor II Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur