Honeywell Sixsiren Manuel utilisateur

SiX

Series

SiXSIREN

Installation Instructions

This wireless siren/strobe is intended for use

with Honeywell controls that support SiX™

series devices.

SiXSIREN

OPEN

Enroll

This device can be enrolled and programmed either

before or after installation.

1. Set the Lyric Controller in Programming Mode and

go to Zone Programming. Select Add New, then

Serial Number. Follow the controller’s instructions

to begin enrollment.

2. Insert four 1.5V AA Lithium batteries (included) to

activate the device and begin the enrollment

process.

3. The Green LED flashes rapidly during enrollment

(up to about 20 seconds*)

*NOTE: Enrollment time varies depending on the signal

strength between the device and the controller.

•The device sends its unique MAC ID address

(Serial Number) and Services information to the

controller.

•The controller registers the device and displays

the transmitter data on screen.

4. Enrollment is confirmed when the Green LED is

ON for 3 seconds and the controller chirps once.

5. Trigger the device tamper switch again to complete

enrollment and press SAVE.

6. The device did not enroll in the system if:

•The White LED flashes, the system chirps and

the device powers down.

•The Green LED flashes rapidly when the device

is removed from the mounting bracket (the

tamper switch is triggered).

To restart the enrollment process, ensure the

system is in programming mode and activate the

tamper switch.

The device can also be manually enrolled. See the

Controller’s Programming Guide for details.

Trigger the device

again to complete

enrollment

Serial Number Loop Number

Zone Description 1 Zone Description 2

Device Type Response Type

Alarm Report Chime Supervision

Panic Home

The Green LED

is ON for 3 seconds

Programming Mode > Zones >

Add New > Serial Number

6Select

SAVE

The LED Flashes; wait

up to about 20 seconds*

After enrolling, update the SiXSIREN firmware (via the

Controller) to ensure the latest version is used. See the

Controller’s instructions.

NOTE: Once enrolled in a system, the device cannot be used with

another controller until it is removed from the current controller. See

the Controller’s instructions for details.

Program the SiXSIREN

Consult the Controller’s instructions for programming the device in the system. sensing –

range is 0°– 120°F (-18°– 49°C); accuracy ±3°F (1.67°C)

Gently twist the top of the Siren

counterclockwise and the

mounting bracket clockwise to

separate them.

Mounting

NOTE: Before mounting the device permanently,

conduct Go/No Go tests (see controller’s

instructions) to verify adequate signal strength and

adjust the device location and orientation as

necessary.

The SiXSIREN can be mounted on the wall or on

the ceiling.

The rear tamper breakout [A] MUST be mounted to

a stud, solid wood, or with a robust wall anchor.

(2)

#6 x 1”

(3.5 mm x 25 mm)

(1)

#4 x 1/4”

(2.9 mm x 6.4 mm)

[A]

Test the SiXSIREN

The SiXSIREN should be tested immediately after installation and weekly. Activate Test Mode remotely from the

Controller (see Controller’s manual for details). The product must be tested at least once a year.

Test Mode tests the sounder and LED:

•Sounder – the Burglary warble tone will sound for 3 seconds.

•LED – the White LED strobe will flash for 15 seconds.

SiXSIREN LEDs and Sounder

Refer to the table below for operation of the four bi-colored LEDs and an 85dB sounder.

R= Red

W= White

G= Green

= ON

=Slow Flash

R=Rapid Flash

=Strobe Flash

=Chirp

=Burglary Warble

=Temporal Pulse 3

=Temporal Pulse 4

LEDs Sounders

R / W G / W Sounder Status

Green Rapid Flashes for

about 20 seconds, then

ON for 3 seconds

Chirps once

Power Up – Enrollment

Green Slow Flashing for

3 seconds

Chirps once

Power Up – Device

enrolled

Green ON for 20 seconds System is Disarmed

Red ON for 20

seconds System is Armed

R W

Alternating Red and

White Flashing Strobe

(continues until the

Alarm is cleared)

Smoke / Heat Alarm

CO Alarm

White Strobe Flashing

Burglary Warble

ON for 3 seconds

Burglary Alarm

Red flashes once

every 45 seconds

Low Battery

Green Flashes slowly for

10 minutes Tamper Activated

Strobe flash = two flashes per second, then OFF for 1 second.

It is best to replace the battery BEFORE the chirping begins. Once started, the sounder continues to chirp until batteries are replaced or die. See

the Battery Replacement section.

Battery Replacement

•Twist the front cover counterclockwise and separate it

from the mounting bracket.

•Remove the batteries, wait 10 seconds and insert four

new batteries of the same type and brand.

Recommended replacement batteries:

-1.5V AA Lithium Batteries [Non-Rechargeable]

-AA Alkaline batteries can be used, but battery life will

be significantly reduced.

NOTE: Do not mix old and new batteries, battery

types or manufacturers.

•Reattach the front cover and twist clockwise to secure it

in place.

BATTERY CAUTION: Risk of fire, explosion and burns.

Do not recharge, disassemble, heat above 212 F (100 C) or

incinerate. Dispose of used batteries properly. Keep away from

children.

Non-Rechargeable

1.5V, AA Lithium

~10

sec

Specifications:

Range: 300 feet nominal indoors (actual range determined by the system in TEST mode)

Battery: Four 1.5V, AA Lithium, Non-Rechargeable; Energizer E

Honeywell 462

Tamper: Cover and Wall tamper

RF Frequency: 2.4GHz

Input Voltage: 3,3VDC

Current: 339 mA, Typical

Siren Output Level: 85 dB at 10 feet

Operating Temperature: 0°to 50°C / 32°to 122°F (Agency Compliance 32°to 120°F / 0°to 49°C)

Relative Humidity: 95% max. (Agency compliance – 93% max), non-condensing

Dimensions: 14.14 cm Diameter x 4.62 cm Thick / 5.5 in. Diameter x 1.8 in. Thick

Weight: xx oz (xx g)

Approval Listings:

FCC / IC

cETLus Listed

Conforms to UL 985 /

UL 1023

Certified to ULC-S545 &

ULC/ORD-C1023

Other Standards:

RoHS

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's

Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis

aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence

reçue y compris les interférences causant une reception indésirable.

RF EXPOSURE

Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm)

from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance

with FCC multi-transmitter product procedures.

MISE EN GARDE EXPOSITION AUX FREQUENCES RADIO

Attention : L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm)

de toutes les personnes.

SUPPORT & WARRANTY

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS

REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest documentation and online support information, please go to:

https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa.

For patent information, see www.honeywell.com/patents

MyWebTech

Warranty

Patents

2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.

Ê800-

15964kŠ

800-21342 11/15 Rev A

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Table des matières

Autres manuels Honeywell Système de sécurité

Honeywell

Honeywell ADEMCO VISTA-10P Instructions de montage

Honeywell

Honeywell VISTA-21iP Manuel utilisateur

Honeywell

Honeywell ADEMCO VISTA-10P Manuel utilisateur

Honeywell

Honeywell INTELLIGUARD 9000 Manuel utilisateur

Honeywell

Honeywell VISTA-128FBPN Instructions de montage

Honeywell

Honeywell Lynx Touch L5100 Manuel utilisateur

Honeywell

Honeywell INTELLIGUARD 9000 Manuel

Honeywell

Honeywell SD500-PSDA Manuel utilisateur

Honeywell

Honeywell ADEMCO CE3 Code Encryptor 3 Instructions de montage

Honeywell

Honeywell ADEMCO Vista-12 Series Manuel utilisateur

Honeywell

Honeywell SEF800HF Manuel utilisateur

Honeywell

Honeywell ADEMCO VISTA SERIES Mode d'emploi

Honeywell

Honeywell LYNX Touch L7000 Series Manuel utilisateur

Honeywell

Honeywell FIRE-LITE ALARMS BG-12LR Manuel utilisateur

Honeywell

Honeywell Galaxy Dimension Manuel d'instructions

Honeywell

Honeywell Galaxy 8 Manuel utilisateur

Honeywell

Honeywell Ademco Vista-48 series Manuel utilisateur

Honeywell

Honeywell INTELLIGUARD 9000 Manuel utilisateur

Honeywell

Honeywell VISTA-32FBPT Manuel utilisateur

Honeywell

Honeywell Lynx Plus Series Manuel utilisateur

Honeywell

Honeywell LYNX Touch Security System Manuel utilisateur

Honeywell

Honeywell Ademco VISTA-20P Manuel utilisateur

Honeywell

Honeywell VISTA-128BPT Mode d'emploi

Honeywell

Honeywell First Alert FA168CPS Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur

Honeywell sixsiren Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques