Honeywell FS24X Manuel utilisateur

–

Installation Guide and Operating

Manual

FSX™ Fire and Flame Detectors

Model FS24X™

FS24X QuadBand Triple IR™

Multi-Spectrum Infrared Electro-Optical Multi-Spectral Digital WideBand IR Sensor

Radiant Energy Fire and Flame Detector

Installation Guide and Operating Manual // Model FS24X

Honeywell 2

Read and understand this manual before

installing or operating equipment.

No part of this document may be copied or reproduced without the express

written permission of Honeywell Analytics.

This manual is subject to change without notice.

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied

warranties of merchantability and fitness for a particular purpose and makes no express warranties except as

may be stated in its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information

and specifications in this document are subject to change without notice.

ACCTTL, ALERT-1, ALARM-2, ALERT-1: ALARM 2, ALERT-1: ALARM-2, ATAG, Clean Room Sentry, COP-i,

Complete Optical Path Integrity, CM1, CM1-A, DartLogic, FireLogic, Fire Signature Analysis, FireBusI, FireBusII,

FirePic, FirePicII, FirePicIII, FirePix, FirePicture, FSC, Fire Sentry Corporation, Fire Sentry Corp., FSX, All FSX

Nomenclature Variations (such as: FS2, FS2X, FS3, FS3X, FS4, FS4X, FS5, FS5X, FS6, FS6X, FS7, FS7X,

FS8, FS8X, FS9, FS9X, FS10X, FS10X, FS11, FS11X, FS12, FS12X, FS14, FS14X, FS15, FS15X, FS16,

FS16X, FS17, FS17X FS18, FS18X, FS19, FS19X, FS20, FS20X, FS24, FS24X, FS24XN, FS26, FS26X,

FS26XN), FS7-2173-2RP, FS System 7, FS System 10, FS7-2173, FS7-2173-RP, FS2000, FS System 2000,

High Speed Flame & Surveillance Detector, Multi-Spectrum QuadBand Triple IR, Multi-Spectrum TriBand, Multi-

Spectrum Tri-Band, Near Band Infrared, Near Band IR, NearBand IR, QuadBand IR, Room Sentry, RS, RS2,

SM2, SM3, SS, SS2, SS2X, SS2-A, SS3, SS3-A, SS3X, SS4, SS4-A, SS4X, SnapShot, SLR-BIT, SuperBus,

SuperSentry, System 2000, Tri-Mode Plot, QuadBand Triple IR Plus, TriBand, Tri-Band, “FS & FSC triangle

logo’s”, WBIR, Wide Band Infrared, WideBand IR, Wide Band IR

are registered trademarks of Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Analytics

Installation Guide and Operating Manual

Honeywell 3

TABLE OF CONTENTSU

PAGE

SECTION 1: INTRODUCTION UT .................................................................................................................................... 4

TU1.1UT TUProduct Overview UT ............................................................................................................................................. 4

TU1.2.1UT TUMechanical Specifications UT .................................................................................................................... 5

TU1.2.2 Electrical Specifications ........................................................................................................................ 5

U1.2.3UUEnvironmental Specifications U............................................................................................................... 5

U1.2.4UUPerformance Specifications U.................................................................................................................. 5

1.2.5 Hazardous Area Classifications ........................................................................................................... 5

1.2.6 Flame Performance Certification .......................................................................................................... 6

U1.3 Features & Benefits .......................................................................................................................................... 7

U1.4 Applications ...................................................................................................................................................... 7

SECTION 2: INSTALLATION U..................................................................................................................................... 8

U2.1 Mounting Instructions ....................................................................................................................................... 8

U2.2 Opening the Detector ...................................................................................................................................... 10

U2.3 Detector Connections ...................................................................................................................................... 11

U2.4 Installation Practices ....................................................................................................................................... 13

U2.5 Start-Up and Commissioning .......................................................................................................................... 14

SECTION 3: OPERATION .........................................................................................................................................16U

U3.1 Principle of Operation ...................................................................................................................................... 16

U3.2 Configuring the Detector ................................................................................................................................. 16

U3.3 LED Status Indicators ..................................................................................................................................... 18

3.4 Normal Operation ............................................................................................................................................ 18

U3.5 Alarm Condition ............................................................................................................................................... 18

U3.6 Fault Conditions .............................................................................................................................................. 19

U3.7 Maintenance .................................................................................................................................................... 19

SECTION 4: APPENDIX ............................................................................................................................................19U

U4.1 Warranty Information ....................................................................................................................................... 20

U4.2 Product Variations ........................................................................................................................................... 21

U4.3 Digital Communication Options ....................................................................................................................... 21

U4.4 Test Lamps ..................................................................................................................................................... 22

4.5 Field of View Restrictor ................................................................................................................................... 22

U23

4.6 Additional Performance Specifications ........................................................................................................... 23

4.6.1 Flame Response Sensitivity ................................................................................................................ 23

4.6.2 False Alarm Immunity .......................................................................................................................... 24

4.7 Drawings ......................................................................................................................................................... 25

4.7.1 Outline and Dimensions ....................................................................................................................... 25

4.7.2 Wiring and Terminal Connections ....................................................................................................... 26

4.7.3 BRE Detector Labels ............................................................................................................................ 28

4.7.4 EN54 Detector Label ............................................................................................................................ 29

INDEX..........................................................................................................................................................................30U

CONTACT HONEYWELL ANALYTICS.....................................................................................................................U31

Installation Guide and Operating Manual

Honeywell 4

SECTION 1: INTRODUCTION

1.1 Product Overview

The Model FS24X™Detectors sense the WideBand IR™

radiant energy of blackbody particulate and molecular

emissions generated by BOTH hydrocarbon and non-

hydrocarbon flames and fires. The WideBand IR spectral

radiant energy wavelengths sensed by the Quad (4) sensors

span from approximately 0.4 to 5.5 microns for the FS24X.

The Model FS24X Multi-Spectrum Fire and Flame Detectors

are designed and Factory Mutual approved for use in Class I,

Div. 1 and 2, Class II and Class III; Class I, Zone 1 AEx d

and Ex d IIC Hazardous Locations and ATEX Certified Ex db

IIC (T4-T6) and Ex tb IIIC (T4-T6) Flameproof (Figure 1-1 &

Figure 1-2).

The FS24X Detectors are available in copper-free Aluminum

or 316 Stainless Steel enclosure. The FS24X Detector

electro-optical electronics module (puck) is enclosed in a

field-replaceable black, hard anodized aluminum puck that

provides superior ruggedness, handling, ease of installation,

and protection against EMI/RFI.

Figure 1-1

FS24X Detector (110° Field of View)

Shown with 316 Stainless Steel Housing

FS24X Detector Field Connectors

The field connections feature two (2) connector choices

for the installer:

1. A removable ten (10) pin screw terminal connector

(J2) for hard-wired relay applications.

2. A removable six (6) pin screw terminal connector

(J1) for analog output or RS-485 Digital

Communication applications.

The removable connectors provide quicker installation

and allows the Detector enclosure to be installed prior to

the Detector Module (puck).

Figure 1-2

FS24X-9 Detector (90° Field of View)

Shown with Copper Free Aluminum Housing

UField Selectable

Configuration Switches

1. The eight (8) pin DIP switch (SW2)

is used to select the Detector’s

Sensitivity and Relay Options.

2. The ten (10) pin DIP switch (SW1)

is used for:

Selecting a unique digital

address (128 choices).

Factory Use

3. The ten (10) position Rotary switch

allows selection of the analog and

digital communication protocol.

Figure 1-3

FS24X and FS24X-9 Detector Puck, (rear view)

Installation Guide and Operating Manual

Honeywell 5

1.2 Detector Technical Specifications

1.2.1 Mechanical Specifications

Enclosure Material: Copper Free Aluminum

316 Stainless Steel

Physical Dimensions: Assembly 4.35 in. (110.49 mm) Height X 4.81 in. (122.24 mm) Diameter

Mounting Holes ¼ in. (6.35 mm) Diameter, 5.50 in. (139.70 mm) Center to Center

Conduit Entries Two (2) ¾ in. NPT or Two (2) 25 mm

Weight: Aluminum 3 lbs. 11 oz. (1.7 kg) approximately

Stainless Steel 7 lbs. 7 oz. (3.4 kg) approximately

Enclosure Rating: IP66 / NEMA 4X

Vibration: Meets or exceeds Mil Spec 810C,

Method 514.2, Curve AW

1.2.2 Electrical Specifications

Input Voltage Range: 18 VDC to 32 VDC

Normal Operation Current: 60 mA (nominal) 205 mA (nominal with heaterP

Maximum Fire Alarm Current: 85 mA (maximum) 235 mA (maximum with heaterP

Relay Contact Rating: 1 Amp @ 24 VDC resistive

Analog Current Output: 0 to 20 mA (Source or Sink, User Selectable)

(400 Ohms Max Load) 0.0 mA (<0.6 mA) = Fault

2.0 mA (±0.6 mA) = Dirty Window Lens

4.0 mA (±0.6 mA) = Normal, Safe (no Fault, no Fire)

20.0 mA (±0.6 mA) = Alarm or Verified Fire Alarm

Screw Terminal Wire Sizes: 12 AWG to 22 AWG (2.50 mm to 0.762 mm)

Use stranded conductors (UnotUsolid core)

1.2.3 Environmental Specifications

Operating Temperature Standard: -40° F to +185° F (-40° C to +85° C)

Extended-TempP

P: -76° F to +230° F (-60° C to +110° C) Optional

Operating Humidity Range: 0 to 95% RH,

100% RH condensing for short periods of time

Storage Temperature: -67° F to +221° F (-55° C to +105° C)

1.2.4 Performance SpecificationsP

Field of View: FS24X detectors have a cone of view of 90° horizontal and

80° vertical with the highest sensitivity on the central axis

Sensitivity: One (1) sq. ft. heptane reference fire at 200 feet

Speed of Response: 2 to 5 seconds (typical)

High Speed Response: Less than 0.5 seconds to “fireball” type fires (if selected)

Spectral Sensitivity: ~0.185 to 0.26 microns and 0.4 microns to 5.0 microns

1.2.5 Hazardous Area Classifications (See Section 4.7.3 on Page 23)

Class I, Division 1, Groups A, B, C & D; Class II, Division 1 Groups E, F & G; Class III; Class I, Zone 1 AEx d /Ex d IIC

Hazardous Locations. ATEX IECEx CertificationClass I, Zone 1, Ex db IIC (T4-T6) and Ex tb IIIC (T4-T6).

All FS24X-9 Detectors All FS24X-2 Detectors

T4: Ta = -60°C to +110°C T4: Ta = -40°C to +110°C

T5: Ta = -60°C to +75°C T5: Ta = -40°C to +75°C

T6: Ta = -60°C to +60°C T6: Ta = -40°C to +60°C

PHeater circuit turns ON only when temperature drops below zero (0) degrees Farenheit (-17° C)P

2The supply connection wiring shall be rated at least 10°C above the rated service temperature (120°C for T4 applications and 85°C for T5

applications)

Installation Guide and Operating Manual

Honeywell 6

1.2.6 Flame Performance Certification (See Sections 4.7.3 and 4.7.4 on page 28 and 29)

Agency Standard Certificate Notes

LPCB EN 54-10:2002 +A1:2005 1175a/02 Sensitivity settings: Very High, High

EN 54-10 Class 1

CPR EN 54-10:2002 +A1:2005 0832-CPR-F0516

Installation Guide and Operating Manual

Honeywell 7

1.3 Features and Benefits

Selectable Sensitivity (four settings)

User can set an FSX Detector to four (4) different Detector sensitivity levels (see Section 3.2).

Selectable Relay Options

User configurable for a variety of dry contact relay interface options (see Section 3.2).

Selectable 4 – 20 mA Output

User can set for Source or Sink non-isolated output (see Section 3.2).

Selectable Communications

User can configure for analog or digital communication outputs such as Modbus (see Section 3.2).

Selectable Digital Communication Address

Users can select unique 7-bit code (128 addresses) (see Section 3.2).

Lower Power Consumption

Requires smaller external power supplies and fewer system backup batteries.

Dual Microprocessors

Reduces the number of discrete Detector components, provides larger programming and memory

capacity, and provides redundant self-checking.

100% Solid-State Quantum IR Sensors

Superior performance, stability, reliability, durability, and ruggedness. Provides higher MTBF and much

wider operating temperature range.

Higher Operating Temperature

185°F (85°C) for more applications and 230°F (110°C) available for higher temperature applications.

Lower Operating Temperature

-40°F (-40°C) for more applications and -76°F (-60°C) available for lower temperature applications.

Built-In Automatic “Through-the-Lens” Self-Test

Monitors window lens obscuration and checks the operation of the Detector’s Sensor Array and Electro-

Optical Electronics Module.

Anodized Field Removable Detector Aluminum Module (Puck)

Rugged, superior protection against EMI/RFI and handling plus easier field installation and replacement.

Three Separate Bright LED’s (Red, Yellow, Green)

Field status indicators with individual LED’s for Alarm, Fault and Normal conditions. Provides superior

Detector status viewing in bright outdoor environments (see Section 3.6).

FSC Windows® based PC Interface

User can perform remote FSX Detector diagnostics, real-time status, Real-Time Graphing (RTG),

SnapShotdata recording, and downloading FirePic’swith Honeywell Analytics’ exclusive FSIM-2

USB Interface Unit and easy to use Windows®based PC Software.

Designed to Detect both Hydrocarbon and Non-Hydrocarbon Fires with one FSXDetector

All fire and flame threats are sensed, not just hydrocarbon fires as with other Triple IR Flame Detectors.

Designed, Manufactured, Tested, and Patented by Honeywell Analytics

Over 30 years of proven fire / flame detection product excellence worldwide.

EN54-10 certified

1.4 Applications

Partial List of Applications:

Refineries Gas Processing Plants Offshore Drilling and Production Platforms

Cogeneration Plants Gas Collection Facilities Petroleum Product Pipelines & Pumping Stations

Petrochemical Plants Gas Turbine Enclosures Commercial and Military Aircraft Hangars

Crude & Product Tank

Farms

LPG Storage/Distribution Rail and Truck Loading/Unloading Terminals

Engine Test Cells General Warehouses Gasoline Loading Terminals

Power Plants Aerosol Filling Facilities Product Storage Terminals

Marine Terminals Paint and Solvent Storage Cold Storage Warehouses

Airport Terminals Marine Engine Rooms Gas Compressor Buildings

Installation Guide and Operating Manual

Honeywell 8

SECTION 2: INSTALLATION

2.1 Mounting Instructions

Consider the following guidelines when selecting Detector location:

1. As with all flame and fire Detectors, avoid areas that contain radiant energy sources (such as radiant

heaters, high intensity lamps, flare-stacks, etc.) in close proximity to the Detector’s field of view.

2. The installation shall take into account that the FS24X orientation should be with the base horizontal

(see Figure 2-1) as the view angle in this direction is 90°. The vertical angle is 90°.

Horizontal Field of View

Figure 2-1

FS24X Graphical View

3. Detectors should not be mounted so that they look up or face the horizon (especially outdoors). Use

a minimum thirty degrees (30°) downward angle with the SM4 swivel mount (see Figure 2-1).

4. Make sure the Detector has a clear, unobstructed view of the threat area. Physical obstructions

between a fire and the Detector may cause the fire to be undetected.

5. The Model SM4 is a 316 Stainless Steel Swivel Mount designed for the Honeywell Analytics Detector

housing. The adapter plate, with the two (2) screw holes (facing away), is attached to the base of the

Detector (see Figure 2-1). The mounting plate, with the four (4) screw holes (facing towards), is used

for mounting the SM4 to a solid surface. Each adjustment increment along an axis is calibrated to

10°. For single axis adjustments, the center section need not be installed.

6. Avoid mounting the Detectors in areas where temperatures exceeds the specified operating

temperature range (see Sections 1.2.3 & 1.2.5).

7. Detector Conduit Entries

a) If only one conduit entry is used, correctly install and seal the conduit plug on the unused entry,

¾ in. NPT or 25mm (see Figure 2-3).

b) Install an approved conduit trap or drain, if required to meet hazardous area classifications per

NFPA 70: National Electrical Code, latest revision.

Installation Guide and Operating Manual

Honeywell 9

Figure 2-2 Figure 2-3

SM4 Swivel Mount Detector (front view)

Figure 2-4

Mounting Instructions (continued)

Note the following Precautions:

1. UDo not touchUthe sensors’ windows on the front of the

Detector electro-optical electronics module (puck). If touched

accidentally, they should be cleaned following the instructions

listed below (see Figure 2-5).

2. When cleaning the Detector’s sensor windows on the puck, it

is best to use Alcohol or IPA sparingly and a cotton swab.

3. There are no serviceable parts inside the Detector puck. If the

puck is opened up or tampered with, all warranties are voided.

FSX Detector Module “puck”

Figure 2-5

CAUTION: Follow static protection procedures while handling the connectors and the wiring

of the Module puck to the Detector. Use a wrist strap connected to earth ground.

Installation Guide and Operating Manual

Honeywell 10

2.2 Opening the Detector

It is necessary to remove the Detector Module puck from the enclosure to access the field connections.

1. Loosen the set screw on the enclosure lid

(see Figure 2-6).

Figure 2-6

2. Turn counterclockwise (CCW) to unscrew

the enclosure lid (see Figure 2-7).

Figure 2-7

3. Loosen the three captive screws on the

Detector Module puck (see Figure 2-8).

Figure 2-8

CAUTION: Disconnect power before

unscrewing the Housing Lid.

Autres manuels pour FS24X

Table des matières

Autres manuels Honeywell Capteur de sécurité

Honeywell

Honeywell RCA902N Manuel utilisateur

Honeywell

Honeywell IS216 Manuel d'installation et d'exploitation

Honeywell

Honeywell Sensepoint XCD Manuel utilisateur

Honeywell

Honeywell Minipeeper C7027A Manuel d'utilisation

Honeywell

Honeywell SPM Flex Manuel utilisateur

Honeywell

Honeywell 2110B30 0 Series Manuel utilisateur

Honeywell

Honeywell Ex-Or MLS2500D Manuel d'installation et d'exploitation

Honeywell

Honeywell 5800PIR-COM Manuel utilisateur

Honeywell

Honeywell Lyric W1 Manuel utilisateur

Honeywell

Honeywell Friedland FGGA08 Series Manuel utilisateur

Honeywell

Honeywell Miller RACDTA-5K6/6FT Manuel de l'opérateur

Honeywell

Honeywell FIRE-LITE ALARMS H365 Manuel utilisateur

Honeywell

Honeywell IRPI8EZS Manuel utilisateur

Honeywell

Honeywell NFPA 1951 Manuel du propriétaire

Honeywell

Honeywell C7061M Manuel d'utilisation

Honeywell

Honeywell ToxiPro CO Manuel utilisateur

Honeywell

Honeywell 5800-OD Manuel utilisateur

Honeywell

Honeywell Miller 8172 Manuel de l'opérateur

Honeywell

Honeywell ESSER 784763 Manuel utilisateur

Honeywell

Honeywell C7061A1020 Manuel utilisateur

Honeywell

Honeywell MDA Scientific MIDAS Manuel utilisateur

Honeywell

Honeywell ADEMCO 5808EU Manuel utilisateur

Honeywell

Honeywell SS2-A Manuel utilisateur

Honeywell

Honeywell FlexGuard 5853AP Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur