Honeywell BSM Instructions de montage

K14864V3 9/10 Rev. A

BSM

Battery Sense Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The Honeywell Battery Sense Module is a control panel

accessory that is used to monitor and report the backup

battery status. Its features are:

Monitors and reports for one or two batteries.

Detects and reports low battery conditions.

Detects and reports if a battery is removed.

Provides deep discharge battery protection if AC

power is lost and the backup battery voltage falls

below a safety threshold of 9.5 to 10 volts.

Additional modules can be used for those control panels

that use additional batteries.

PACKAGE CONTENTS

The following items are included:

Battery Sense Module with bracket

Battery Harness (qty 2)

Summary of Connections label

SPECIFICATIONS

Physical: 3-1/8” L x 2-3/4” W x 3/4” H

(80mm x 70mm x 20mm)

Electrical:

Input Voltage: 12VDC nominal (from control panel)

Input Current: 20mA (max used by BSM)

Current Handling Capability: 2.3A maximum

(Control panel load must not exceed 2.3A.)

INSTALLATION

1. Select a suitable area in the control panel where

the mounting will not interfere with testing or

servicing of other components.

2. Clip the Battery Sense Module to the cabinet edge.

CONNECTIONS

1. Refer to the Connections Diagram on other side.

When connecting leads, support the module to

prevent stress on the circuit board.

2. Connect the module's power leads to the control

panel's 12VDC backup battery power terminals.

3. Connect backup battery A to the module. Then

connect backup battery B (if present) to the module.

4. If only one backup battery is being used, depress

the ENROLLMENT switch to toggle the Battery

Sense Module to sense only one battery.

ULC

When used with one battery and the total

load is greater than 1.5A, jumper the

Battery A terminals and the Battery B

terminals on the Battery Sense Module to

the backup battery.

5. For non-Honeywell control panels, connect the

ZONE OUT to an unused control panel zone. (Do

not use a fire zone.)

Note: For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT terminal on

the BSM. The Honeywell control panel will

automatically detect a low or missing battery

through the panel's battery cable.

6. Affix the supplied Summary of Connections label to

the inside of the control panel.

CONFIGURATION

1. Refer to the control panel's installation guide for

details on fault monitoring.

2. For non-Honeywell control panels, program the

connected zone for the Battery Sense Module to

detect an active high fault condition.

ZONE OUT

BAT

BSM-001-V0

B AT. A PANEL

B AT. B

DOCUMENTATION AND ONLINE SUPPORT

For the latest documentation and online support information, please go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14864V3cŠ

K14864V3 9/10 Rev. A

STATUS LEDs (A and B)

STEADY ON Battery is present and good.

BLINKING Battery is programmed to be

present, and is NOT present.

OFF Battery is NOT programmed to be

present.

ENROLLMENT Switch

Default condition is for 2

batteries.

Depress once for 1 battery.

To the control panel battery terminals.

To Battery A terminals.

To Battery B terminals.

To a non-Honeywell

control panel zone for

fault monitorin

Note:

For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT ter-

minal on the BSM. The Honeywell

control panel will automatically detect

a low or missing battery through the

panel's battery cable.

Autres manuels Honeywell Unité de contrôle

Honeywell

Honeywell satronic DMG 971 Instructions d'utilisation

Honeywell

Honeywell PRO4200 Manuel utilisateur

Honeywell

Honeywell VG.010A Manuel utilisateur

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manuel utilisateur

Honeywell

Honeywell Kromschroder GIK Series Manuel utilisateur

Honeywell

Honeywell Krom Schroeder VAN Series Manuel utilisateur

Honeywell

Honeywell 5496 Mode d'emploi

Honeywell

Honeywell HS10S Manuel utilisateur

Honeywell

Honeywell TR70 Manuel utilisateur

Honeywell

Honeywell W8735ER Manuel utilisateur

Honeywell

Honeywell R7795A Manuel utilisateur

Honeywell

Honeywell 4232CBM Instructions de montage

Honeywell

Honeywell PENA D MLS2000SSP Manuel d'installation et d'exploitation

Honeywell

Honeywell AlarmNet IGSMHS Instructions de montage

Honeywell

Honeywell Galaxy 2 Series Manuel utilisateur

Honeywell

Honeywell GSMVLP5 Instructions de montage

Honeywell

Honeywell RV277 Manuel utilisateur

Honeywell

Honeywell L4017 Manuel utilisateur

Honeywell

Honeywell VSxF-2 Manuel utilisateur

Honeywell

Honeywell Esser 2 Series Manuel utilisateur

Honeywell

Honeywell VR4920Z 1000 Manuel utilisateur

Honeywell

Honeywell S89C Manuel utilisateur

Honeywell

Honeywell Ex-Or CDW12U5 Manuel d'installation et d'exploitation

Honeywell

Honeywell VGF Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur