Honeywell NOTIFIER ID2000 Series Mode d’emploi

ID2000 installation &

commissioning

manual

997-433-000-5, Issue 5 May 2010

ID2000 Series Installation & Commissioning Manual

Contents

i 997-433-000-5, Issue 5

May 2010

The ID2000 Series Range of Fire Control Panels

ID2000 Series Installation & Commissioning Manual

Contents

ii997-433-000-5, Issue 5

May 2010

Contents

1 Introduction 1

1.1 CE Marking 1

1.2 System Design and Planning 1

1.3 Personnel 1

1.4 General 1

1.4 Date-dependent Functions 2

Installation: Sections 2-7

2 Installation Guide 3

2.1 How to Use this Guide 3

2.1.1 Related Documents 3

2.1.2 Warnings and Cautions 3

2.1.3 Tips 3

2.1.4 Glossary of Icons 4

2.2 Pre-Installation Check List 5

2.2.1 Some DO’s and DONT’s 5

2.3 Transient Protection 6

2.4 Installation 7

2.4.1 Checking Your Panel for Damage 7

2.4.2 What to do if Your Module is Damaged 8

2.4.3 Back Box Fixing 9

2.4.4 Electronics Modules 10

2.5 Replacing the Electronics Modules 11

2.6 Flush Mounting Bezel (Optional) 11

2.7 Mounded Front Covers 13

3 Cabling 14

3.1 Cabling Instructions 14

3.1.1 Cable Terminations 15

3.2 Cable Installation Notes 16

3.2.1 Introduction 16

3.2.2 Quality of Cable and of Cable Installation 16

3.3 EMC Considerations 17

3.3.1 Screen Termination 17

3.3.2 Ferrite Sleeves (Optional) 17

3.4 MICC Cables 17

4 Sensors and Modules 18

The following markings are used either

on the panel hardware or in the

documentation. They have the following

meaning:

WARNING: Risk of electric

shock. Before working on

mains connections, ensure

mains power supply to the

panel is disconnected.

CAUTION: Refer to the

accompanying documentation.

(When used in the

documentation, this marking is

normally associated with

additional instructions).

ID2000 Series Installation & Commissioning Manual

Contents

iii 997-433-000-5, Issue 5

May 2010

4.1 EN54 Requirements 18

4.1.1 Loop Devices - Sensors and MCPs 18

4.1.2 Loop Devices - Isolators 18

4.2 Loop Wiring Testing 18

5 Panel Electronics Modules 19

5.1 Introduction 19

5.2 Kit PSU3A 20

5.2.1 Procedure 20

5.3 Dual Transmission Path/Booster Module 23

5.4 Main Chassis 25

5.4.1 main Chassis Configurations 25

5.4.1 Procedure 25

5.5 Extension Chassis 26

5.5.1 Zones 17-80 LED Extension Chassis 26

5.5.2 Extension Chassis (With Printer) 26

5.6 PRN-ID Printer 27

5.6.1 Fitting the Paper Roll 27

5.6.2 Printer Used with Stainless Steel Cover 28

5.7 Display PCB 29

5.8 Base PCB 30

5.8.1 Fitting the Replacement Base PCB 31

5.8.2 Cables and Wiring 31

5.9 Processor PCB 32

5.10 Loop Interface PCB 33

5.10.1Cables and Wiring 33

5.11 Isolated RS232 Interface PCB 34

5.11.1Cables and Wiring 35

5.12 Isolated RS485 Interface PCB 36

5.12.1Cables and Wiring 37

5.13 Label Inserts 37

6 Repeaters and Network 38

6.1 Connecting Repeaters 38

6.2 Network Connections 39

7 VDU 40

8 Commissioning 41

8.1 Introduction 41

8.2 Preliminary Checks 41

ID2000 Series Installation & Commissioning Manual

Contents

iv997-433-000-5, Issue 5

May 2010

8.3 Powering the Panel 42

8.4 External Wiring 42

8.4.1 Introduction 42

8.4.2 Loop Checks Before Connecting Wiring 43

8.4.3 Connecting the Loop Wiring to the Panel 44

8.4.4 Loop Checks After Connecting Wiring 44

8.4.5 24V Auxiliary Outputs Check 45

8.4.6 Sounder Circuits Check 45

8.4.7 Fault Relay Wiring 45

8.5 Batteries 46

8.5.1 Connecting the Batteries 46

8.5.2 Battery Disposal 47

8.6 Earth Fault Monitoring 47

8.7 Volt-free Contact Output Option 48

8.8 Repeaters 48

8.9 Configuration and Handover 48

8.10 System Test 48

8.10.1 Zone Walk Test 48

8.10.2 Control Output Test 48

9 Maintenance 47

9.1 Routine Testing 47

9.2 Batteries 47

9.3 Cleaning 47

Appendices:

Appendix 1 Fault Messages and

Possible Meanings A1-1 to A1-5

Appendix 2 Specifications A2-1 to A2-5

Appendix 3 ID2000 System

Design Guide A3-1 to A3-3

ID2000 Series Installation & Commissioning Manual

997-433-000-5, Issue 5

May 2010

Introduction

1 Introduction

The purpose of this manual is to provide the user with all

recommended procedure descriptions and full technical

details for the successful installation and commissioning

of NOTIFIER’s ID2000 Series stand-alone fire alarm

controllers and repeaters or for a complete ID2000 Series

integrated Fire Control System.

Procedures described in this manual include appropriate

warnings and cautions to guide the user towards adopting

safe and methodical work practices during the installation

and commissioning phases.

1.1 CE Marking

This panel is CE Marked to show that it conforms to the

requirements of the following European Community

Directives:

The EMC Directive 2004/108/EEC, by the application of

the following EMC Standards:

!EN 61000-6-3: Electromagnetic Compatibility (EMC)

Generic emission standard for Residential,

Commercial and Light industrial environments

!EN 50130-4: EMC Product family standard: Immunity

requirements for components of fire, intruder and

social alarm systems.

Low Voltage Directive 2006/95/EC, by the application of

the safety standard:.

!EN 60950-1: Safety of information technology

equipment.

The Constructive Products Directive 89/1-6/EC, by the

application of the following standards:

!EN 54-2: Fire detection and fire alarm systems -

Control and indicating equipment.

!EN 54-4: Fire detection and fire alarm systems - Power

supply equipment.

1.2 System Design and Planning

It is assumed that the system, of which the ID2000 Series

fire control equipment is a part, has been designed by a

competent fire alarm system designer in accordance with

the requirements of EN54 Part 14 and any other local

codes of practice that are applicable.

The design drawings should clearly show the positions of

all the ID2000 Series control equipment and field devices.

1.3 Personnel

Installation of this product must be carried out only by

suitably-qualified electrical engineers.

ID2000 Series Installation & Commissioning Manual

997-433-000-5, Issue 5

May 2010

Introduction

1.4 General

The ID2000 Series of intelligent fire alarm controllers are

designed for use with NOTIFIER’s range of addressable

analogue sensors, control and monitoring modules and

addressable call points.A unique signalling protocol is used,

having digital address and control signals, and analogue

pulse width monitoring for the reply data from devices. The

ID2000 Series supports the use of OPAL protocol devices,

but can only poll these devices in CLIP protocol mode.

The ID2000 Series control panel design complies with the

requirements of EN54 Part 2 and Part 4.

The design of the ID2000 Series of fire control panels is

based on a modular build concept which offers the user

completely flexible system solutions. Each control panel

comprises a number of separate build modules to simplify

the installation process. The electronic components are

contained in an easy-to-fit module called the main chassis.

The control panel can be used with either an internal or

external Power Supply Unit (PSU).

The ID2000 Series fire control panels are available either as:

a. Multi-loop, user-configurable Basic Equipment Kits

which are configurable with up to 8 loops, or as

b. Factory-configured, ID2002 2-loop control panels.

Any references in these manuals to configurations with

more than two loops are not applicable to the ID2002

control panel.

Each control panel has space provision for two sealed, lead-

acid batteries.

The serial communications interface operates under

RS485 protocol and enables networking of control panels

and the connection between control panels and repeaters.

While every effort is made to ensure the accuracy of the

content of this manual, the manufacturer reserves the

right to change the information without notice.

Installation

The ID2000 Series modules are easy to install providing

the recommended procedures described in this manual

are followed. To avoid inadvertant contamination of the

main chassis, comprising the PCBs and PSU, if mounted

internally, the manufacturer recommends that these items

are installed in the back box only after all other trades have

completed their tasks.

1.5 Date-dependent Functions

It should be noted that the calendar end date for this

product is 31/12/2099 (two thousand and ninety nine) and

it will perform correctly up to this date.

The calendar function has not been tested beyond this

date.

Only fit the electronics

module after all the other

trades have completed

their tasks!

ID2000 Series Installation & Commissioning Manual

Installation Guide

3 997-433-000-5, Issue 5

May 2010

2 Installation Guide

2.1 How to Use this Guide

This Installation Guide is intended to provide you with

simple guidelines on how to install an ID2000 Series fire

control panel or system, quickly and safely.

For each stage in the ID2000 Series panel installation

and commissioning procedures a brief description is given

of its purpose, complete with detail drawings, flow

diagrams and/or other graphics to make the instructions

easy to follow. Where required, procedures may be broken

down into one or more related flow diagrams, the number

being dependent upon the complexity of the defined task.

2.1.1 Related Documents

The guide does not describe any of the panel

programming or operating stages, as these are covered

by other related manuals. For more information refer to:

!ID2000 Series Operating Manual (ref. 997-434-XXX)

!ID2000 Series Panel Configuration Manual

(ref. 997-435-XXX)

!ID2000 Series Off-line Configuration Manual

(ref. 997-436-XXX)

2.1.2 Warnings and Cautions

Where appropriate, this guide and the remainder of the

manual include advisory warnings and cautions to remind

you to consider safety at all times, especially when

following the procedures described in this manual.

You are alerted to any areas where high voltage [i.e.

non-Safety Extra-low Voltage (SELV)] is present, or

where there may be a risk of damage to static-sensitive

devices if the recommended procedures described in

this manual are not followed. An example of a high

voltage warning and anti-static caution is provided to the

left of this paragraph.

The ID2000 Series control panel has many powerful built-

in features which, if used inappropriately, may contravene

the requirements of EN54. Where there is a possibility

of such an occurence, a suitable warning is given with

brief details of the EN54 requirement. A typical EN54

non-compliance warning is illustrated at left.

2.1.3 Tips

‘Handy tips’ are included, where appropriate, to assist

you in following quick and safe procedures for fire

detection system installation and integration.

Look for the ‘TIP!’ icon and supporting text, typically

illustrated at left.

WARNING High Voltage!

Take suitable precautions

to avoid electric shock.

EN54-2: 13.7

Maximum of 512

Sensors and/or

MCPs per system.

Magnetise the tip of your

screwdriver to help when

offering small screws to

holes in confined spaces.

ID2000 Series Installation & Commissioning Manual

Installation Guide

4997-433-000-5, Issue 5

May 2010

2.1.4 Glossary of Icons

Throughout this Installation and Commissioning Manual

and other supplied user documentation a number of

simple icons are used, either on their own or together

with larger illustrations, to simplify a particular task or

process.

The following icons are used to advise or indicate:

a) DO follow the recommended procedure or method

b) DO NOT use this procedure or method

c) Inspection of an item or sub-assembly is required at

this point

d) Following a defined process meets the required

approval/inspection criteria or standards

e) Following a defined process does not meet the

required approval/inspection criteria or standards

f) Additional items to be considered

g) This icon placed next to a pushbutton requires you to

press it as part of a described process, such as isolate

or test, or while programming the panel. Where two or

more icons are used, a number may be placed on or

near each hand to indicate the order of selection: 1

coming before 2, etc.

h) Activity process step - flow arrow for single action or

iterative actions

i) Leader arrow - used with activity processes

j) Sounder operating

k) Sounder not-operating or silenced

l) Digital clock timer - press and hold the applicable

pushbutton for the time indicated

ID2000 Series Installation & Commissioning Manual

Installation Guide

5 997-433-000-5, Issue 5

May 2010

2.2 Pre-installation Check List

Before installing the ID2000 equipment or fitting sensors,

you must first ensure that the following criteria have been

met. Failure to do this may not only result in damage to

the equipment, but may also cause problems when

commissioning the equipment or adversely affect its

performance.

2.2.1 Some DO’s and DON’T’s

Before selecting a location for the control panel and

devices, DO make sure that:

a) The operating ambient temperature is in the

recommended range:

5°C to 35°Cand

b) The relative humidity is between:

5% and 95%

c) The panel is wall mounted in a position which allows

clear visibility of displays and easy access to operating

controls. The height above floor level should be chosen

such that the LCD is just above normal eye level

(approximately 1.5 metres)

d) DO NOT locate the panel where it is exposed to high

levels of moisture

e) DO NOT locate the panel where there are high levels

of vibration or shock

1.5m

Autres manuels pour NOTIFIER ID2000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Panneau de contrôle

Honeywell

Honeywell IQ8Control C Manuel utilisateur

Honeywell

Honeywell DX Connexion Series Manuel utilisateur

Honeywell

Honeywell NOTIFIER SFP-5UD Series Manuel utilisateur

Honeywell

Honeywell OMNI 408 Instructions de montage

Honeywell

Honeywell W834A Manuel utilisateur

Honeywell

Honeywell Galaxy Dimension series Guide de configuration rapide

Honeywell

Honeywell Notifier NFS2-640 Manuel utilisateur

Honeywell

Honeywell MINI-ZONE 69-1361 Guide de démarrage rapide

Honeywell

Honeywell TrueZONE HZ432K/U Manuel utilisateur

Honeywell

Honeywell Fire-Lite Alarms MS-9600 Manuel utilisateur

Honeywell

Honeywell ControLinks YP7999A1000 Manuel utilisateur

Honeywell

Honeywell Fire-Lite Alarms MS-9600LS Manuel utilisateur

Honeywell

Honeywell SILENT KNIGHT 6700 Manuel utilisateur

Honeywell

Honeywell Excel 5000 System Series Manuel utilisateur

Honeywell

Honeywell MiniZone EMM-3U Manuel d'utilisation

Honeywell

Honeywell NFS-3030 Instructions d'installation et d'utilisation

Honeywell

Honeywell Fire-Lite Alarms MS-9050UD Manuel utilisateur

Honeywell

Honeywell AQ250 Series Manuel d'utilisation

Honeywell

Honeywell TrueZONE HZ432 Manuel utilisateur

Honeywell

Honeywell Vigilon Plus Manuel utilisateur

Honeywell

Honeywell NOTIFIER AM-8200 Manuel du propriétaire

Honeywell

Honeywell 5110XM Manuel utilisateur

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manuel de formation

Honeywell

Honeywell Fire-lite ECC-LOC Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques