Honeywell NOTIFIER INSPIRE E10 Manuel de formation
Notifier INSPIRE E10/E15
Fire Alarm Control Panels
Commissioning
Instructions
2
CONTENTS
Related Documents 4
Conventions 4
Introduction 5
Commissioning 6
Preliminary Checks 6
Sensors and Modules checks 8
Loop Wiring Tests 9
POL 200 tool 11
To perform loop wiring checks, Using a Multimeter: 11
Connecting the opal/clip loop wiring to the panel 12
Initial Power Up 13
Device Loop wiring and Checks 13
RS485 Cable check 13
Other External Wiring 14
Configuration and System Test 15
Configuration Tool 15
System Test 15
Maintenance 16
Routine Testing 16
Batteries 16
Fault monitoring and rectification 16
Messages and their Meanings 17
Fault Events 18
General FAULTs 18
Processor related faults 19
Configuration related faults 20
PSU & Charger related faults 21
Wiring & Driver related faults 26
Communication & Mapping Faults 28
Field Device Faults 31
Maintenance Events 38
Test Operation Messages 39
3
Notifier INSPIRE E10/E15 Control Panels - Commissioning
Disablement Events 40
Alarm Events 41
4
RELATED DOCUMENTS
This guide does not describe any of the panel operating and
installation instructions, refer to:
INSPIRE E10/E15 Control Panel Operating Manual (Part
number HOP3389EN)
INSPIRE E10/E15 Control Panel Installation Manual
(Part number HOP1389EN)
CONVENTIONS
Where appropriate, in this manual there are advisory
warnings and cautions to remind you to consider safety
at all times, especially when following the procedures
described.
This symbol precedes a note that highlight
important information that is normally
hidden in the main text.
This symbol precedes information
that warns of danger that may result
in serious injury or death, also used
as a caution to prevent damage to the
equipment.
This symbol precedes information about
compliance with standard(s).
ABBREVIATIONS
CIE Control and Indicating Equipment
CPU Central Processing Unit
E10 Smaller 10U size Panel enclosure
E15 Larger 15U size Panel enclosure
EMC Electromagnetic compatibility
FARE Fire Alarm Routing Equipment
FRE Fault Routing Equipment
FPE Fire Protection Equipment
HMI HumanMachine Interface
IO or I/O Input or Output
LED Light emitting diode (light)
MCP Manual call point
OC or O/C Open circuit
RAL European colour matching system
SC or S/C Short circuit
SELV Separated Extra Low Voltage
PE Protective Earth
PELV Protected ExtraLow voltage
PSE Power Supply Equipment
5
Notifier INSPIRE E10/E15 Control Panels - Commissioning
Introduction
The purpose of this manual is to provide the user with recommendations on procedure for Commissioning of
INSPIRE Fire Alarm Control Panel based Fire Control System.
6
Commissioning
Commissioning
To bring the Notifier INSPIRE E10/E15 Control panel into an operational state ready for configuration, follow the
steps detailed below. Information on how to configure the panel is given in the Notifier INSPIRE E10/E15 Control
Panel Configuration Tool Manual.
The Notifier INSPIRE E10/E15 Control panel provides comprehensive fault monitoring and diagnostic routines
which will prove very useful during system commissioning. Any fault message displayed at the panel carry a
meaning and possible action that a trained engineer can take to remedy the fault, see section headed Messages
and their meaning.
The following must be remembered about FAULT conditions when commissioning the Notifier INSPIRE E10/E15
Control panel, faults can result from:
A configuration mismatch between the site design, installation of panel and wiring of external equipment, or
External conditions, such as the proximity of a strong RFI source, having an adverse effect on the panel, or
The failure of a panel module and / or the PSU.
PRELIMINARY CHECKS
Before initial power connection, check that:
01 All modules are correctly seated into the respective module carrier slots.
02 All internal wiring is properly connected.
03 Ensure the loop wiring and external circuits have NOT, at this stage, been connected with terminal blocks
fitted to respective terminal pins on module carrier.
04 The appropriate end-of-line devices are connected, such as to I/O channel circuit.
7
Notifier INSPIRE E10/E15 Control Panels - Commissioning
Ensure Modules are installed into their allowed slot locations
It is required that the Charger module is always fitted in Slot 1 of the module carrier and
CPU Module fitted in Slot 2 of Module Carrier.
ROW 1
ROW 2
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 7
Slot 8
Slot 9
Slot 10
Slot 11
Slot 12
Charger
E10 Panel range
E15 Panel range
6/2-slots
Module
Carriers
Link module
for Module
carriers
expansion
-
-
Termination
Termination
Module for
Battery &
PSU cables
-
-
-
-
-
-
-
2-Rows Link
Modules with
power and Ethernet
patch cables
ROW 1ROW 2
E10
-
-
ROW 1
6
X
X
Allowed to be fitted in these
slots of Module carriers.
X - Not allowed in these
slots of Module Carriers
-
-
-
-
-
-
-
-
-
E15
6
6
- 6-slots, supplied fitted
-
-
-
-
-
-
-
- Not applicable
6
Modules:
- Loop Opal 2X
- COM Dual (FAT/FBF)
- FIRE/FAULT routing
- COM Serial (RS232/RS485
- I/O 4-CH
- NET ID2NET
2
2
-
-
--
Slot 13
Slot 14
X
X
X
X
X
X
X
X
X
/
E10 E15
X
X
X
X
- 2-slots Extension
optional
CPU
X
/
X
X
X
X
X
X
X
X
E10 E15
X
X
X
X
/
E10 E15
E10
E10
E15
E15
E15
E15
-
-
2
E10
E10
E10
E15
IMPORTANT
1 2 3 4 5 6 7 8 9 10
123456
789
10 11 12 13 14
Slot No:->
Slot No:->
Slot No.
Module carriers
Module carriers
- panel range.
/
E10 E15
2
Module carriers
Module: Module:
8
Commissioning
SENSORS AND MODULES CHECKS
Each device has an associated instruction leaflet showing the correct interconnections for various applications.
Survey the site to check and ensure devices are installed in the location identified on 'As fitted system wiring
drawings' and according to the instructions.
The Notifier INSPIRE E10/E15 Control Panel support supports devices incorporating internal isolators, providing
the bases with the additional positive leg loop wiring connectors (type B501 AP) are used. However, devices will
work satisfactorily when used with bases without these additional wiring connectors except the internal isolator,
when fitted, cannot be operated.
The Notifier INSPIRE E10/E15 Control panel Dual Loop module Opal (HOP433100) has the capacity to
allows connection of up to 318 loop OPAL devices per analogue loop, consisting of up to 159 detectors and 159
modules.
A loop can operate in legacy CLIP mode which can be activated through a dedicated license. The capacity of a
CLIP loop is limited to 99 detectors + 99 other devices
9
Notifier INSPIRE E10/E15 Control Panels - Commissioning
LOOP WIRING TESTS
Refer to the module installation instructions to identify the terminals for cable connections.
NEVER use a high-voltage tester on the detection loop.
Once any loop devices are connected, no high-voltage testers, such as Megger may be used on the loop circuit;
low-voltage testers, such as multimeter, may be used.
With isolators in each device the positive conductor of the loop will be open circuit.
In general
Check the continuity of each leg of the loop and measure the end-to-end resistance. We recommend that the
system must be wired using 2-core cable only.
Check the continuity of the cable screen and measure end-to-end resistance, which must be a very low
resistance value .
Check also there is no continuity between cable screen and loop +ve and -ve wires of the loop.
10
Commissioning
Typical connections of addressable devices to a loop are shown below:
1
2
3
41
2
3
4
LOOP OPAL X2
1 2 3 4 5
6 7 8 9 10
1Loop 1 OUT +VE
2Loop 1 OUT -VE
3
4Loop 1 IN +VE
5Loop 1 IN -VE
6Loop 2 OUT +VE
7Loop 2 OUT -VE
8
9Loop 2 IN +VE
10 Loop 2 IN -VE
1234
5
0
1
2
3
45
6
7
8
9
6789101112
0
1
2
3
45
6
7
8
9
CBA
1234
5
EOL
EOL
-
+
Loop Input
Loop Input
2 Input 1 Output Interface
Manual Call Point
-
+
Loop Output
Loop Outout
Detector
Detector
Control panel
Autres manuels pour NOTIFIER INSPIRE E10
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Honeywell Panneau de contrôle
Honeywell
Honeywell IQ8Control C Manuel utilisateur
Honeywell
Honeywell ControLinks YP7999A1000 Manuel utilisateur
Honeywell
Honeywell Silent Knight SKE Series Manuel utilisateur
Honeywell
Honeywell Fire-Lite Alarms MRP-2001 Manuel utilisateur
Honeywell
Honeywell Notifier NFS-320 Manuel utilisateur
Honeywell
Honeywell W-MMF Manuel utilisateur
Honeywell
Honeywell SLC Manuel utilisateur
Honeywell
Honeywell TrolATemp TZ-3 TotalZone Manuel d'utilisation
Honeywell
Honeywell Notifier NFS-320/E/C Manuel utilisateur
Honeywell
Honeywell HVC0001 Manuel utilisateur
Honeywell
Honeywell Galaxy 2-44+ Manuel utilisateur
Honeywell
Honeywell TrolaTemp MABS EZ-2 Manuel d'utilisation
Honeywell
Honeywell VISTA-128BPT Guide de démarrage rapide
Honeywell
Honeywell NOTIFIER AM1000 Manuel du propriétaire
Honeywell
Honeywell Accenta Manuel utilisateur
Honeywell
Honeywell W8835A Manuel utilisateur
Honeywell
Honeywell Notifier AFP-3030 Manuel utilisateur
Honeywell
Honeywell Gamewell Flex 402 Manuel utilisateur
Honeywell
Honeywell GALAXY 16103 Manuel utilisateur
Honeywell
Honeywell Notifier RP-2001 Manuel utilisateur
