Honeywell XENON 1902 Manuel utilisateur

™

Xenon™ 1900/1902

Area-Imaging Scanner

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in speci-

fications and other information contained in this document without prior notice,

and the reader should in all cases consult HII to determine whether any such

changes have been made. The information in this publication does not repre-

sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnish-

ing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, repro-

duced, or translated into another language without the prior written consent of

HII.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Web Address: www.honeywellaidc.com

Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows

XP, and the Windows logo are trademarks or registered trademarks of Microsoft

Corporation.

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Product Agency Compliance - Xenon 1900

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for

help.

If necessary, the user should consult the dealer or an experienced radio/

television technician for additional suggestions. The user may find the fol-

lowing booklet helpful: “Something About Interference.” This is available at

FCC local regional offices. Honeywell is not responsible for any radio or

television interference caused by unauthorized modifications of this equip-

ment or the substitution or attachment of connecting cables and equipment

other than those specified by Honeywell. The correction is the responsibil-

ity of the user.

Use only shielded data cables with this system. This unit has been tested

with cables less than 3 meters. Cables greater than 3 meters may not meet

class B performance.

Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell may void the FCC authorization to oper-

ate this equipment.

UL Statement

UL listed: UL60950-1.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Opera-

tion is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe A est conforme à la norme NMB-003

du Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

cUL Statement

cUL listed: CSA C22.2 No.60950-1-07.

Europe

The CE marking indicates compliance to 2004/108/EC EMC Directive

with Standards EN55022 CLASS B, EN55024, EN61000-3-2,

EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage Direc-

tive, when shipped with recommended power supply.

For further information please contact:

Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Honeywell International Inc. shall not be liable for use of our product with

equipment (i.e., power supplies, personal computers, etc.) that is not CE

marked and does not comply with the Low Voltage Directive.

Waste Electrical and Electronic Equipment

Information

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PAR-

LIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical

and electronic equipment (WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health

and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to

use the appropriate take-back systems for product disposal. Those sys-

tems will reuse or recycle most of the materials of the product you are dis-

posing in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you to

use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling sys-

tems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environ-

mental performances of this product.

Germany

If your product is marked with the GS symbol, then the product

has been issued a GS certificate showing compliance to EN

60950-1, Second Edition.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548 EMC requirement

Mexico

Conforms to NOM-019.

Japan

Russia

Gost-R certificate

South Korea

This product meets Korean agency approval.

Taiwan

If the following label is attached to your product, the product meets Taiwan

agency approval:

BSMI Standard: CNS13438, CNS14336

依據標準 : CNS13438, CNS14336

International

LED Safety Statement

LEDs have been tested and classified as “EXEMPT RISK GROUP” to the

standard: IEC 62471:2006.

CB Scheme

Certified to CB Scheme IEC 60950-1, Second Edition.

Laser Safety Statement

If the following label is attached to your product, it indicates the product

contains a laser engine or laser aimer:

This device has been tested in accordance with and complies with

IEC60825-1 ed2.0 and 21 CFR 1040.10 and 1040.11, except for deviations

pursuant to Laser Notice No.50, dated June 24, 2007.

LASER LIGHT, DO NOT STARE INTO BEAM, CLASS 2 LASER PROD-

UCT, 1.0 mW MAX OUTPUT: 630-650nM.

LASER LIGHT. DO NOT STARE INTO BEAM

1.0 mW MAX OUTPUT: 650nM

IEC 60825-1 Ed 2 (2007).

CLASS 2 LASER PRODUCT

Complies with 21 CFR 1040.10 and 1040.11

except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

Caution - use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation expo-

sure.

Patents

For patent information, please refer to www.honeywellaidc.com/patents.

Solids and Water Protection

The Xenon 1900 has a rating of IP41, immunity of foreign particles and dripping

water.

Warning

To reduce the possibility of heat-related injuries, avoid touching sec-

tions of the scanner that feel warm.

Product Agency Compliance - Xenon 1902 and

CCB01-010BT Base

USA

FCC Part 15 Subpart C

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell may void the FCC

authorization to operate this equipment.

Use only shielded data cables with this system. This unit has been tested

with cables less than 3 meters. Cables greater than 3 meters may not meet

class B performance.

UL Statement

UL listed: UL60950-1.

Canada

Industry Canada

This device complies with Canadian RSS-210. Operation is subject to the

following conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that

may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil ISM est conforme à la norme CNR-210 du Canada. Son fonc-

tionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

C-UL Statement

C-UL listed: CSA C22.2 No.60950-1-07 for I.T.E product safety.

Europe

The CE marking on the product indicates that this device is in confor-

mity with all essential requirements of the 1999/5/EC R&TTE Directive.

In addition, complies to 2006/95/EC Low Voltage Directive, when

shipped with recommended power supply. For further information, con-

tact:

Honeywell Imaging & Mobility Europe BV

International Inc.

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Honeywell shall not be liable for use of our product with equipment (i.e.,

power supplies, personal computers, etc.) that is not CE marked and does

not comply with the Low Voltage Directive. This equipment is intended for

use throughout the European Community and has been assessed to the

following standards:

EN 300 328

EN 301 489-1

EN 301 489-17

EN60950-1

Waste Electrical and Electronic Equipment

Information

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PAR-

LIAMENT AND OF THE COUNCIL on waste electrical and electronic

equipment (WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health

and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to

use the appropriate take-back systems for product disposal. Those sys-

tems will reuse or recycle most of the materials of the product you are dis-

posing in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you to

use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling sys-

tems, contact your local or regional waste administration.

You may also contact your supplier for more information on the environ-

mental performances of this product.

Germany

If your product is marked with the GS symbol, then the product

has been issued a GS certificate showing compliance to EN

60950-1, Second Edition.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548 EMC requirements.

Brazil

This product is approved by Anatel, according to the procedures regulated

by Resolution No. 242/2000 and meets the technical requirements applied.

Este produto está homologado pela ANATEL, de acordo com os procedi-

mentos regulamentados pela Resolução No. 242/2000 e atende aos requi-

sitos técnicos aplicados.

Para maiores informações, consulte o site da ANATEL – www.anatel.gov.br

China

SRRC Radio Certificate.

CCC safety (CCB01-101BT base only)

Modelo: Xenon 1902

2876-10-6583

(01)07898927490072

" Este equipamento operaem caráter secundário, isto é, não tem

direito aproteção contrainterferênciaprejudicial, mesmo de estações

do mesmo tipo, e não pode causar interferênciaasistemas operando

em caráter primário."

Autres manuels pour XENON 1902

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Lecteur de codes-barres

Honeywell

Honeywell 4850DR Manuel utilisateur

Honeywell

Honeywell Granit XP 199 i Series Manuel utilisateur

Honeywell

Honeywell XENON 1902G-BF Dimensions

Honeywell

Honeywell Dolphin 7600 Manuel utilisateur

Honeywell

Honeywell IS4225 ScanGlove Manuel utilisateur

Honeywell

Honeywell MK7580-30A38-00-A - MS7580 Genesis - Wired Barcode... Manuel utilisateur

Honeywell

Honeywell 3820SR0C0B-0FA0E Manuel utilisateur

Honeywell

Honeywell MK9535-79A540 - MS9535 VoyagerBT - Wireless Portable Barcode... Manuel utilisateur

Honeywell

Honeywell VOYAGER 1202G BF Manuel utilisateur

Honeywell

Honeywell Fusion MS3780 Manuel utilisateur

Honeywell

Honeywell PX4-6IE-CUTR-IG-1 Manuel utilisateur

Honeywell

Honeywell Voyager 1602g Manuel utilisateur

Honeywell

Honeywell HH1800 Manuel utilisateur

Honeywell

Honeywell MS9500 Voyager Series Manuel utilisateur

Honeywell

Honeywell 3800i Manuel utilisateur

Honeywell

Honeywell 3800G04-USBKITE Manuel utilisateur

Honeywell

Honeywell Solaris MS7820 Manuel utilisateur

Honeywell

Honeywell MS7320 InVista Manuel utilisateur

Honeywell

Honeywell MX7 Tecton Manuel utilisateur

Honeywell

Honeywell MS9520 Voyager Manuel utilisateur

Honeywell

Honeywell Hyperion 1300G Manuel utilisateur

Honeywell

Honeywell Vuquest 3310g Manuel utilisateur

Honeywell

Honeywell 3800 Linear Series Manuel utilisateur

Honeywell

Honeywell Quick Check 890 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur