Honeywell Granit 1920i Manuel utilisateur

Granit 1920i

Industrial Direct Part Mark (DPM) Area-Imaging Scanner

Quick Start Guide

1920i-EN-QS Rev A

7/17

Note: Refer to your user’s guide for information about cleaning

your device.

Get Started

Turn off computer’s power before connecting the scanner, then

power up the computer once the scanner is fully connected.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connect the Scanner

When connecting the scanner, make sure the cable is pushed

tightly into the scanner. Loosen the locking plate and slide it

over the base of the cable connector to lock the cable in place.

Tighten the screw.

USB:

RS232 Serial Port:

Reading Techniques

The Granit 1920i scanner uses a red aiming dot to locate bar

codes. Center the aimer on the bar code. If the bar code being

scanned is on a shiny or highly reflective surface, you may need

to tilt the scanner slightly to read the code.

Standard Product Defaults

The following bar code resets all standard product default set-

tings.

USB Serial

Scan the following code to program the scanner to emulate a

regular RS232-based COM Port. If you are using a Microsoft®

Windows® PC, you will need to download a driver from the Hon-

eywell website (www.honeywellaidc.com). The driver will use the

next available COM Port number. Apple® Macintosh computers

recognize the scanner as a USB CDC class device and automati-

cally use a class driver.

Note: No extra configuration (e.g., baud rate) is necessary.

USB PC Keyboard

Scan the following code to program the scanner for a USB PC

Keyboard.

Standard Product

Defaults

USB Serial

USB PC Keyboard

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan

the numeric bar code(s) from page 11, then the Save bar code to

program the keyboard for your country. By default, national

character replacements are used for the following characters: #

$ @ [ \ ] ^ ‘ { | } ~.

Note: For a complete list of country codes, see the User’s Guide

for your product.

Country Code Scan Country Code Scan

Arabia 91 Korea 93

Belgium 1 Portugal 13

China 92 Russia 26

France 3 Spain 10

Germany/Austria 4 Sweden/Finland 2

Great Britain 7 Switzerland 6

Hungary 19 Thailand 94

IBM Financial 90 Turkey (Q) 24

Italy 5 USA (Default) 0

Japan 28 Vietnam 95

Program Keyboard Country

Save

Active Aimer

By default, the scanner and the aiming beam remain off until

you press the trigger. When Active Aimer is set to On, whenever

the scanner is moved, the aiming beam appears so you can aim,

then scan a bar code with a trigger press.

DPM Illumination Settings

By default, the Granit 1920i cycles through the Direct Illumina-

tion - Top and Bottom, and Indirect Illumination settings. To fur-

ther refine the scanner’s ability to read DPM codes, scan one of

the following four illumination setting codes. Only one of these

illumination settings can be used.

Direct Illumination - Top and Bottom

This setting enables both top and bottom illumination. It is rec-

ommend when reading printed label bar codes and DPMs on

highly reflective surfaces.

Active Aimer On

Direct Illumination - Bottom

This setting enables just the bottom illumination. It is recom-

mend when primarily reading dot peen bar codes. You may need

to tilt the scanner at an angle to read from reflective surfaces.

Indirect Illumination

This setting is recommend when reading bar codes on curved or

rough surfaces.

Low Contrast Codes

This setting is recommend when reading very low contrast bar

codes. Scan the following code to program the scanner to cycle

through both Direct Illumination - Top and Bottom and Indirect

Illumination with multiple exposure settings.

Low Contrast Data Matrix Enhancements

The Granit 1920i scanner reads low contrast Data Matrix codes

by default. However, if you are having trouble reading non-dot

peen Data Matrix bar codes, it may be helpful to scan Low Con-

trast Data Matrix Enhancements Off.

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab

Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

* Low Contrast Data Matrix

Enhancements On

Low Contrast Data Matrix

Enhancements Off

Add CR Suffix

Add Tab Suffix

Remove Suffix

Table des matières

Autres manuels Honeywell Lecteur de codes-barres

Honeywell

Honeywell QUANTUME IS3480 Manuel utilisateur

Honeywell

Honeywell Virtuos 1D Manuel utilisateur

Honeywell

Honeywell Xenon 1910 Manuel utilisateur

Honeywell

Honeywell VOYAGER 1202G BF Manuel utilisateur

Honeywell

Honeywell 1900GSR-2 Manuel utilisateur

Honeywell

Honeywell XL 800 Series Manuel utilisateur

Honeywell

Honeywell Hyperion 1300G Manuel utilisateur

Honeywell

Honeywell Hyperion 1300G Manuel utilisateur

Honeywell

Honeywell Captuvo SL22 Manuel utilisateur

Honeywell

Honeywell Hyperion 1300G Manuel utilisateur

Honeywell

Honeywell Genesis 7580G Fiche technique

Honeywell

Honeywell I-Class Mark II Manuel utilisateur

Honeywell

Honeywell HF800 Series Manuel utilisateur

Honeywell

Honeywell MS9500 Voyager Series Manuel utilisateur

Honeywell

Honeywell 7820 Solaris Manuel utilisateur

Honeywell

Honeywell 4600g Manuel utilisateur

Honeywell

Honeywell 4600g Manuel utilisateur

Honeywell

Honeywell Voyager 9520/40 Manuel utilisateur

Honeywell

Honeywell MK3780-71A38 Manuel utilisateur

Honeywell

Honeywell Voyager 9520 Manuel utilisateur

Honeywell

Honeywell CM4680 Manuel utilisateur

Honeywell

Honeywell Granit 1280i Manuel utilisateur

Honeywell

Honeywell Dolphin 7600 Manuel utilisateur

Honeywell

Honeywell Solaris MS7820 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur