HMS Networks Intesis INBACDAL0640200 Instructions de montage

This information is subject to change without notice

URL https://www.intesis.com

Rev.1.0

1 / 2

INBACDAL0640200

DALI to BACnet gateway

Order Code: INBACDAL0640200

Installation Sheet rev.1.0

HMS Industrial Networks S.L.U ©

SAFETY INSTRUCTIONS

!WARNING

Follow carefully this safety and installation instructions.

Improper work may lead to serious harmful for your health

and also may damage seriously the Intesis gateway and/or

any other equipment connected to it.

The Intesis gateway must be installed by accredited electrician or

similar technical personnel, following all the safety instructions given

here and in accordance always with the country legislation for

installation of electric equipment.

The Intesis gateway cannot be installed outdoors or exposed to direct

solar radiation, water, high relative humidity or dust.

The Intesis gateway must only be installed in a restricted access

location.

In case of wall mount, fix firmly the Intesis gateway on a not vibrating

surface following the instructions next.

In case of DIN rail mount fix the Intesis device properly to the DIN rail

following the instructions below.

Mounting on DIN rail inside a metallic cabinet properly connected to

earth is recommended.

Disconnect always power of any wires before manipulating and

connecting them to the Intesis gateway.

A power supply with an NEC Class 2 or Limited Power Source (LPS)

and SELV rated is to be used.

Respect always the expected polarity of power and communication

cables when connecting them to the Intesis device.

Supply always a correct voltage to power the Intesis device, see details

of voltage range admitted by the device in the technical characteristics

below.

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.

Dispose of Used Batteries according to the instructions. Battery

replacement shall be done by an authorized installer.

CAUTION: The device is to be connected only to networks without

routing to the outside plant, all communication ports are considered for

indoor only and can be connected SELV circuits only.

This device was designed for installation in an enclosure. To avoid

electrostatic discharge to the unit in environments with static levels

above 4 kV, precautions should be taken when the device is mounted

outside an enclosure. When working in an enclosure (ex. making

adjustments, setting switches etc.) typical anti-static precautions

should be observed before touching the unit.

Safety instructions in other languages can be found at:

https://intesis.com/docs/manuals/v6-safety

Use the Ethernet connection or the Console Port (mini USB type B

connector included) for communication between the gateway and the

configuration tool. See CONNECTIONS below and follow instructions

of user’s manual for more details.

INSTALLATION

Follow instructions next to properly install the gateway.

Disconnect from mains the power supply before connecting it to the

Intesis gateway.

Disconnect power of any bus or communication cable before

connecting it to the Intesis gateway.

Mount the Intesis device on the wall or DIN rail following the instruction

given below, respecting the safety instructions given above.

Connect a NEC Class 2 or Limited Power Source (LPS) and SELV

rated power supply to the Intesis gateway, respect the polarity if DC

power or Line and Neutral if AC power. Apply always a voltage within

the range admitted by the Intesis gateway and of enough power (see

technical characteristics).

Circuit-breaker must be used before the power supply. Rating 250V-

6A.

Connect the communication cables to the Intesis device, see details on

the user's manual.

Power the Intesis device and the rest of devices connected to it.

NOTE: The device cannot be installed in air-handling space.

Wall Mount

1. Separate the fixing clips in the bottom of the box, pushing

them to the outside until hear the "click" which indicates that

now the clips are in position for wall mount, see in the figure

below.

2. Use the holes of the to fix the box in the wall using screws.

Use the template below for the wall wholes.

Clips in their original position Clips in position for wall mount

(for DIN rail mount)

DIN Rail Mount

With the clips of the box in their original position, insert first the box

in the upper edge of the DIN rail and later insert the box in the down

part of the rail, using a small screwdriver and following the steps in

the figure below.

Press

CONFIGURATION

Use the Configuration Tool to configure the gateway.

See instructions to download and install the latest version at:

https://intesis.com/docs/software/intesis-maps-installer

Use the Ethernet connection or the Console Port (mini USB type B

connector included) for communication between the gateway and the

configuration tool. See CONNECTIONS below and follow instructions

of user’s manual for more details.

Owner’s Record

The serial number is located at the rear of the gateway.

Record this information in the space provided below.

Refer to it whenever you contact upon your gateway

dealer or support team regarding this product.

Serial No.

This information is subject to change without notice

URL https://www.intesis.com

Rev.1.0

2 / 2

Enclosure

Plastic, type PC (UL 94 V-0)

Net dimensions (dxwxh): 90x88x56 mm

Recommended space for installation (dxwxh): 130x100x100mm

Color: Light Grey. RAL 7035

Battery

Size: Coin 20mm x 3.2mm

Capacity: 3V / 225mAh

Type: Manganese Dioxide Lithium

Mounting

Wall.

DIN rail EN60715 TH35.

Console Port

Mini Type-B USB 2.0 compliant

1500VDC isolation

Terminal Wiring

(for power supply and

low-voltage signals)

Per terminal: solid wires or stranded wires (twisted or with

ferrule)

1 core: 0.5mm2… 2.5mm2

2 cores: 0.5mm2… 1.5mm2

3 cores: not permitted

If cables are more than 3.05 meters long, Class 2 cable is required.

USB port

Type-A USB 2.0 compliant

Only for USB flash storage device

(USB pen drive)

Power consumption limited to 150mA

(HDD connection not allowed)

Power

1 x Plug-in screw terminal block (3 poles)

Positive, Negative, Earth

24VDC +/-10%

Push Button

Button A: Check the user manual

Button B: Check the user manual

Operation

Temperature

0°C to +60°C

Ethernet

1 x Ethernet 10/100 Mbps RJ45

2 x Ethernet LED: port link and activity

Operational

Humidity

5 to 95%, no condensation

Port A

1 x DALI port (Plug-in screw terminal block orange 2 poles)

1500VDC isolation from other ports

DALI guaranteed power: 235mA

Voltage rating: 16VDC

1 x Plug-in screw terminal block green (2 poles)

Reserved for future use

Protection

IP20 (IEC60529)

LED

Indicators

10 x Onboard LED indicators

2 x Run (Power)/Error

2 x Ethernet Link/Speed

2 x Port A TX/RX

2 x Port B TX/RX

1 x Button A indicator

1 x Button B indicator

Switch A

(SWA)

1 x DIP-Switch for serial EIA485 configuration:

Reserved for future use

PORT B

1 x Serial EIA232 (SUB-D9 male connector)

Reserved for future use

1 x Serial EIA485 Plug-in screw terminal block (3 poles)

A, B, SGND (Reference ground or shield)

1500VDC isolation from other ports

(except PORT B: EIA232)

Switch B

(SWB)

1 x DIP-Switch for serial EIA485 configuration:

Position 1:

ON: 120 Ω termination active

Off: 120 Ω termination inactive

Position 2-3:

ON: Polarization active

Off: Polarization inactive

CONNECTIONS

ELECTRICAL & MECHANICAL FEATURES

Power Supply

Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply. Respect polarity applied

of terminals (+) and (-). Be sure the voltage applied is within the range admitted (check table below). The power

supply can be connected to earth but only through the negative terminal, never through the positive terminal.

Ethernet / BACnet IP (UDP) / Console (UDP & TCP)

Connect the cable coming from the IP network to the connector ETH of the gateway. Use an Ethernet CAT5

cable. If communicating through the LAN of the building, contact the network administrator and make sure traffic

on the port used is allowed through all the LAN path (check the gateway user manual formore information). With

factory settings, after powering up the gateway, DHCP will be enabled for 30 seconds. After that time, if no IP is

provided by a DHCP server, the default IP 192.168.100.246 will be set.

PortA / DALI

Connect the DALI bus to connectors A4 (+), A3 (-) of gateway’s PortA. The Intesis gateway provides

16VDC (+/-2%) DALI voltage to the bus.

PortB / BACnet MSTP

Connect the EIA485 bus to connectors B1 (-), B2 (+) and B3 (SNGD) of gateway’s PortB. Respect the polarity.

Remember the characteristics of the standard EIA485 bus: maximum distance of 1200 meters, maximum 32

devices connected to the bus, and in each end of the bus it must be a termination resistor of 120 Ω. The gateway

has an internal bus biasing circuit that incorporates the termination resistor. If you install the gateway in one of

the ends of the bus, then do not install an additional termination resistor in that end.

Console Port

Connect a mini-type B USB cable from your computer to the gateway to allow communication between the

Configuration Software and the gateway. Remember that Ethernet connection is also allowed. Check the user

manual for more information.

USB

Connect a USB storage device (not a HDD) if required. Check the user manual for more information.

Power Supply

Ethernet

BACnet IP

USB

storage

BACnet MSTP

Console

Port

100 mm (h)

100 mm (w)

130 mm (d)

DALI

This marking on the product, accessories, packaging or literature (manual) indicates that the product contains electronic

parts and they must be properly disposed of by following the instructions at https://intesis.com/weee-regulation

Autres manuels HMS Networks Porte

HMS Networks

HMS Networks Intesis INBACDAL0640500 Instructions de montage

HMS Networks

HMS Networks Anybus Communicator Manuel utilisateur

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Manuel utilisateur

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Manuel utilisateur

HMS Networks

HMS Networks Intesis INMBSDAL0640200 Instructions de montage

HMS Networks

HMS Networks Intesis IN485HIT001R000 Manuel utilisateur

HMS Networks

HMS Networks Intesis 700 Series Manuel utilisateur

HMS Networks

HMS Networks Intesis IN771PAN00 O000 Series Instructions de montage

HMS Networks

HMS Networks Anybus Wireless Bolt CAN Manuel utilisateur

HMS Networks

HMS Networks Intesis IN701-KNX Series Manuel utilisateur

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Manuel utilisateur

HMS Networks

HMS Networks Intesis INMBSFGL016O000 Instructions de montage

HMS Networks

HMS Networks Intesis IN775FGL00 O000 Series Manuel utilisateur

HMS Networks

HMS Networks Intesis INMBSDAL0640500 Instructions de montage

HMS Networks

HMS Networks Intesis IN770AIR00XO000 Manuel utilisateur

HMS Networks

HMS Networks Intesis INMBSDAL1280200 Instructions de montage

HMS Networks

HMS Networks Intesis IN770AIR00 O000 Series Manuel utilisateur

HMS Networks

HMS Networks Ewon Flexy 205 Instructions d'installation et d'utilisation

HMS Networks

HMS Networks Intesis INMBSDAL1280200 Instructions de montage

HMS Networks

HMS Networks Ewon Netbiter EC300 Series Guide de l'utilisateur

HMS Networks

HMS Networks Intesis IN776MHI00 O000 Series Manuel utilisateur

HMS Networks

HMS Networks Intesis IN770PAN00 O000 Series Instructions de montage

HMS Networks

HMS Networks Intesis INMBSDAL1280200 Instructions de montage

HMS Networks

HMS Networks Intesis INKNXMEB 0000 Series Instructions de montage

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur