Hitachi VSP G130 Mode d’emploi

nstalling your VSP G130 storage system

Hitachi Virtual Storage Platform G130 storage systems are designed for self-installation, so you can set up your storage

system for the first time without assistance from a Hitachi Vantara representative.

Child Topics

•Step 1: Unpack the storage system

•Step 2: nstall the storage system into a rack

•Step 3: Connect the storage system to power

•Step 4: Cable a management console

A customer-supplied computer is used to set up and manage your storage system.

•Step 5: Power on the storage system

•Step 6: Perform the initial setup

nitial setup of the storage system is performed using the Windows-based management console.

•Step 7: Make host connections

•Step 8: Register your storage system with Hitachi Vantara support

f you have not already registered for access to Hitachi Support Connect, do so now. Otherwise, you will not be

able to download and install Hi-Track Remote Monitoring system, and you will encounter delays in getting your

storage system running and supported.

•Step 9: nstall Hi-Track Remote Monitoring system

•Where to go from here

After concluding the self-installation successfully, perform the following post-installation activities.

Step 1: Unpack the storage system

Before you begin

Make sure your data center meets all site preparation requirements before you install the storage system. n addition, if

you are not using a Hitachi Universal V2 rack, make sure the electrical specifications of your rack meet the power

requirements of the storage system.

Procedure

1. nspect all materials for signs of damage. f you see damage, discontinue the installation and contact your Hitachi

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

Vantara representative.

2. f your storage system did not arrive factory-installed in a rack, loosen the band around the cartons and open all

boxes. Remove all packing materials, envelopes, and boxes from the cartons.

3. Retain all packing materials and cartons in case you need to transport or ship the storage system in the future.

4. Check the items you received against the packing list. f any items are missing or damaged, discontinue the

installation and contact your Hitachi Vantara representative.

5. Place the keys for the front bezel in a safe place. You will need them to attach the bezel to the front of the

controllers.

6. f your storage system arrived already factory-installed in a rack, skip step 2 and proceed to Step 3: Connect the

storage system to power.

Parent Topic

•nstalling your VSP G130 storage system

Step 2: nstall the storage system into a rack

Mount the controller into the Hitachi Universal V2 rack or into a 4-post E A 310-D compliant 19-inch rack with square

mounting holes and rear-facing power distribution units (PDUs).

NoteHitachi Vantara provides rail kits (part number A34V-600-850-UN -S) for mounting the storage system controller

into third-party racks. Mounting rails are shipped in a separate box. The left rail has the letter L cut into the sheet metal,

as shown in the following figure. The right mounting rail has no similar marking. The kit includes more screws than are

required for securing the rails to the rack.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

The following instructions describe how to install the controller into a Hitachi Universal V2 rack. For information about

installing the controller in a third-party rack, see the documentation for that rack.

WARN NGDue to the heavy weight of the controller, use a mechanical lift or at least three people to lift and mount the

controller in the rack.

Before you begin

• Make sure you have a 19-inch rack that is secure and cannot fall over.

• Make sure the rack has one or more PDUs installed.

• Verify that all power cables are removed from the AC power receptacles on the rear of the controller.

• nstall the rack stabilizers before mounting the storage system in the rack.

Procedure

1. Loosen the four adjustment screws, if needed, so that the rail halves can be adjusted freely to fit between the front

and rear vertical rack posts.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

2. Facing the front of the rack, find an empty 2U location where you will install the controller.

3. Place the left mounting rail as shown in the following figure, and then use two flathead screws to secure the rails to

the front vertical post on the rack.

NoteThe flathead screws are M5x10 (PZ-2), where PZ-2 refers to the size and type of the Philips head.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

4. Slide the length of the left mounting rail to fit the length of the rack.

5. Use two flathead screws to secure the rails to the rear vertical post on the rack.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

6. Tighten the four screws on the left mounting rail.

7. Repeat steps 1 through 6 to attach and secure the right mounting rail to the right side of the rack.

8. Position the controller so the front faces the front of the rack, and then slide the controller gently onto the rails.

Stop sliding when the mounting flanges on the front of the controller touch the vertical face of the rack.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

9. Find the washers, O-rings, and screws included with the bezel bracket mounting kit (part number

043-100885-01.P). Then install a washer, O-ring, and screw (one per side) between the mounting profile of the

rack and the mounting "ears" of the controller. The screw engages the threaded hole in the rail.

tem Description

1 Screw

2 O-ring

3 Washer

The rack installation for your controller should resemble the following figure.

tem Description

1 Washers, O-rings, and screws securing the controller to the front of the rack

Parent Topic

•nstalling your VSP G130 storage system

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

Step 3: Connect the storage system to power

The storage system's input voltage is auto-adjusting for 100-120 (+6%) / 200-240 (-11%) VAC, 50-60 Hz power

connections. Power is provided through two power supplies, one per controller.

For best practice, establish power redundancy by routing each power supply to independent PDUs and then routing the

PDUs to separate external power sources on different branch circuits. This arrangement enables the storage system to

continue operating if AC power is lost to one power supply.

NoteMultiple outlets in a PDU or power strip do not constitute an independent electrical source.

Procedure

1. Confirm that all power sources are off.

2. Connect an AC power cable to the power receptacle on the rear of each controller.

3. Route the power cables from each controller to separate PDUs, and then use the pre-installed tie wraps at each

controller power receptacle to secure the power cables, as shown in the following figure.

4. Connect the PDUs to separate external power sources on different branch circuits.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

tem Description

1 PDUs on the left and right sides of the rack

Parent Topic

•nstalling your VSP G130 storage system

Step 4: Cable a management console

A customer-supplied computer is used to set up and manage your storage system.

Before you begin

• Obtain a Category 5 or better Ethernet cable.

• Obtain a customer-supplied Windows-based PC that will serve as the management console for setting up the

storage system for the first time and, thereafter, to manage the storage system. The management console must

have a supported web browser: nternet Explore version 11 or later, Chrome, or Firefox.

Procedure

1. Connect one end of the Ethernet cable to the management port on the rear of either controller. The following figure

shows the connection to the management port on controller 1.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

tem Description

1 Management port on the rear of controller 1

2 Management console

2. Connect the other end of the cable to a management console.

Parent Topic

•nstalling your VSP G130 storage system

Step 5: Power on the storage system

1. Confirm that the power cables on the rear panel are connected to separate PDUs, as shown in the following figure.

Then connect the PDUs to external power sources.

NoteFor best practice, establish power redundancy by routing the power connections from each PDU to external

power sources on different branch circuits.

To prevent the storage system from being turned off by accident, make sure the external power sources are not

controlled by a wall switch.

https://knowledge.hitachivantara.com/Documents/Storage/VSP_G130_GF350_GF370_GF700_GF900/88-03-0x/ nstallation/0…

Updated: Mon, 01 Feb 2021 07:07:26 GMT

Autres manuels pour VSP G130

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Stockage

Hitachi

Hitachi Travelstar 2.5-INCH HTS547575A9E384 Manuel utilisateur

Hitachi

Hitachi AMS 2000 Series Manuel utilisateur

Hitachi

Hitachi Deskstar 7K500 Manuel utilisateur

Hitachi

Hitachi Travelstar 7K60 Manuel utilisateur

Hitachi

Hitachi AMS 2100 Instructions d'installation

Hitachi

Hitachi Deskstar 7K400 Manuel utilisateur

Hitachi

Hitachi Travelstar 4K120 Manuel utilisateur

Hitachi

Hitachi Ultrastar HUS103030FL3600 Manuel utilisateur

Hitachi

Hitachi IC25N040ATMR04-0 - Travelstar 40GB Laptop Hard Drive 9.5mm 2.5 Inch Notebook... Manuel utilisateur

Hitachi

Hitachi Deskstar 7K80 Manuel utilisateur

Hitachi

Hitachi G900 Manuel d'utilisation et d'entretien

Hitachi

Hitachi DK23EB - Travelstar Series 20 GB Hard Drive Manuel utilisateur

Hitachi

Hitachi 3.5-INCH HDS725050KLA360 Manuel utilisateur

Hitachi

Hitachi Deskstar 7K160 Manuel utilisateur

Hitachi

Hitachi VSP G/F350 Mode d’emploi

Hitachi

Hitachi VSP G1000 Manuel utilisateur

Hitachi

Hitachi SVP F 00 Series Manuel utilisateur

Hitachi

Hitachi TAGMASTORE MK-90RD011-25 Manuel utilisateur

Hitachi

Hitachi HTS541616J9AT00 - Travelstar 160 GB Hard... Manuel utilisateur

Hitachi

Hitachi 88-02-0 Series Manuel d'utilisation et d'entretien

Hitachi

Hitachi External USB Storage Manuel utilisateur

Hitachi

Hitachi 4000 Guide d'application

Hitachi

Hitachi 88-06-0x Manuel d'utilisation et d'entretien

Hitachi

Hitachi HTS541212H9AT00 Manuel d'installation et d'exploitation

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur