Hitachi CP-WU9100 Manuel utilisateur

ENGLISH

WARNING ►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

►Heed all the warnings and cautions in the manuals or on the product.

►Follow all the instructions in the manuals or on the product.



First of all ............................................ 2

Entries and graphical symbols explanation ......2

Important safety instruction ..............................2

Regulatory notices .............................. 3

About Electro-Magnetic Interference ................3

About Waste Electrical and Electronic Equipment

...4

Contents of package........................... 4

Installing the lens unit ......................... 5

Preparing for the remote control ......... 5

Arrangement ....................................... 6

Connecting with your devices ............. 7

Ferrite core for HDMI cable ................ 7

Fastening the adapter cover ............... 8



Connecting power supply ................... 9

Turning on the power ........................ 10

Adjusting the projector's elevator ..... 11

Adjusting the lens position ................ 11

Displaying the picture ....................... 12

Turning off the power ........................ 14

Replacing the lamp ........................... 15

Cleaning and replacing the air lter

.. 18

Replacing the

internal clock battery....................... 20

Using the CD manual ....................... 21

Specications ................................... 22

Troubleshooting

- Warranty and after-service ........... 24

Contents

NOTE • In this manual, unless any comments are accompanied, “the

manuals” means all the documents provided with this product, and “the product”

means this projector and all the accessories came with the projector.

Projector

CP-WU9100/CP-HD9950

User's Manual (concise)

Thank you for purchasing this projector.

Read through this manual before using this product, safely use this product.

First of all

Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the product

as follows, for safety purpose. Know their meanings beforehand, and heed them.

Important safety instruction

The following are important instructions for safely using the product. Be sure to

follow them when handling the product. The manufacturer assumes no responsi-

bility for any damage caused by mishandling that is beyond normal usage dened

in these manuals of this projector.

WARNING

This entry warns of a risk of serious personal injury or even death.

CAUTION This entry warns of a risk of personal injury or physical damage.

NOTICE This entry notices of fear of causing trouble.

WARNING ►Never use the product in or after an abnormality (for example,

giving off smoke, smelling strange, took a liquid or an object inside, broken, and

so on.) If an abnormality should occur, unplug the projector urgently.

►Situate the product away from children and pets.

►Keep small parts away from children and pets. If swallowed, consult a

physician immediately for emergency treatment.

►Do not use the product during electrical storms.

►Unplug the projector from the power outlet if the projector is not being used.

►

Do not connect the projector to a power supply while no lens unit is attached to it.

►Do not open or remove any portion of the product, unless the manuals direct

it. For internal maintenance, leave it to your dealer or their service personnel.

►Use only the accessories specied or recommended by the manufacturer.

►Do not modify the projector or accessories.

►Do not let any things or any liquids enter to the inside of the product.

►Do not get the product wet.

►

Do not place the projector where any oils, such as cooking or machine oil, are used.

Oil may harm the product, resulting in malfunction, or falling from the mounted position.

►Do not apply a shock or pressure to this product.

- Do not place the product on an unstable place such as the uneven surface or

the leaned table.

- Ensure the product is stable. Place the projector so that it does not protrude

from the surface where the projector is placed on.

- Avoid from any impact, this projector is made with precision parts.

- Remove all the attachments including the power cord and cables, from the

projector when carrying the projector.

►

Do not look into the lens and the openings on the projector, while the lamp is on,

since the projection ray may cause a trouble on your eye.

►

Do not approach the lamp cover and the exhaust vents, while the projection lamp

is on. Allow the lamps to cool before touching them.

ENGLISH

Regulatory notices

About Electro-Magnetic Interference

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

This product may cause interference if used in residential areas. Such use must

be avoided unless the user takes special measures to reduce electromagnetic

emissions to prevent interference to the reception of radio and television

broadcasts.

In Canada

CAN ICES-3(A) / NMB-3(A).

In the US and places where the FCC regulations are applicable

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential

area is likely to case harmful interference in which case the user is required to

correct the interference at his own expense.

INSTRUCTIONS TO USERS: Some cables have to be used with the core set.

Use the accessory cable or a designated type cable for the connection. For cables

that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Contents of package

Your projector should come with the items

shown below. Check that all the items are

included. Contact your dealer immediately if any

items are missing.

(1) Remote control

(2) Power cord

(3) Computer cable

(4) Ferrite core and Band (x2)

(5) Cable tie (x2)

(6) User’s manuals (Book x1, CD x1)

(7) Security label

(8) Application CD

(9) Adapter cover

NOTE • Keep the original packing materials for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

• The projector may make a rattling sound when tilted, moved or shaken, since

a ap to control the air ow inside of the projector has moved. Be aware that

this is not a failure or malfunction.

About Waste Electrical and Electronic Equipment

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries or accumulators included with this equipment, display

the chemical symbol Hg, Cd, or Pb, then it means that the battery has a

heavy metal content of more than 0.0005% Mercury or more than, 0.002%

Cadmium, or more than 0.004% Lead.

WARNING ►Keep small parts away from children and pets. Take care

not to put in the mouth. If swallowed, consult a physician immediately for

emergency treatment.

(7)

(8)

(2)

(3)

(1)

(4)

(5)

(9)

(6)

ENGLISH

Preparing for the remote control

Insert the batteries into the remote control before using it. If the remote control

starts to malfunction, try to replace the batteries. If you do not plan to use the

remote control for long period, remove the batteries from the remote control and

store them in a safe place.

1. Holding the hook part of the battery

cover, remove it.

2. Align and insert the two AA batteries

according to their plus and minus

terminals as indicated in the remote

control. (Use the appropriate AA

carbon-zinc or alkaline batteries (non-

rechargeable) according to laws

and regulations.

3. Replace the battery cover in the direction

of the arrow

and snap it back into place.

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in re, injury and/or pollution of the surrounding environment.

• When replacing the batteries, replace both of the batteries with new batteries

of the same type. Do not use a new battery with a used battery.

• Be sure to use only the batteries specied. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery.

If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

Installing the lens unit

See the manual of the optional lens.

WARNING ►

Install the projector where you can access the power outlet easily.

►Install the projector in a stable horizontal position.

• Do not use any mounting accessories except the accessories speci ed by the

manufacturer. Read and keep the manuals of the accessories used.

•

For special installation such as ceiling mounting, be sure to consult your dealer

beforehand. Speci c mounting accessories and services may be required.

• Do not set the projector on the terminal side, rear end, or front.

• Do not attach nor place anything on the projector unless otherwise speci ed

in the manual.

►Do not install the projector near thermally conductive or  ammable things.

►

Do not place the projector where any oils, such as cooking or machine oil, are used.

►Do not place the projector in a place where it may get wet.

• DLP chip(s) is/are precision-made parts. In rare cases, pixels may be missing

or lit, but this is not a malfunction.

• Direct high-power laser beam onto the lens surface can damage the DLP

chip(s).

CAUTION ►Place the projector in a cool place with suf cient ventilation.

• Keep a space of 50 cm or more between the projector and other objects such

as walls.

• Do not stop up, block nor cover the projector's vent holes.

• Do not place the projector at places that are exposed to magnetic  elds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place.

• Do not place the projector near humidi ers.

NOTICE ►Position the projector to prevent light from directly hitting the

projector’s remote sensor.

►

Do not place the projector in a place where radio interference may be caused.

►Set the ALTITUDE of the SERVICE item in the OPTION menu correctly. It is

recommended to leave it at AUTO usually. If the projector is used with a wrong

setting, it may cause damage to the projector itself or the parts inside.

Arrangement

Refer to tables T-1 to T-2 at the back of this manual as well as the following to

determine the screen size and projection distance. The values shown in the table

are calculated for a full size screen.

Projector top

Projector bottom

Ⓗ×Ⓥ : Screen size

ⓐ:

Projection distance

(from the front of the projector

unit)

ⓑ,ⓒ: Screen height

ENGLISH

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform the

connection, according to the following instructions. Refer to gures F-1 to F-5 at the

back of this manual.

WARNING ►Use only the appropriate accessories. Otherwise it could cause

a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched.

►

Heat may build up in the USB wireless adapter, to avoid possible burns discon-

nect the projector power cord for 10 minutes before touching the adapter.

CAUTION ►For a cable with a core at only one end, connect the end with

the core to the projector. That may be required by EMI regulations.

►Before connecting the projector to a network system be sure to obtain the

consent of the administrator of the network.

►

Do not connect the LAN port to any network that might have the excessive voltage.

►

The designated USB wireless adapter that is sold as an option is required to use

the wireless network function of this projector. Before connecting the USB wireless

adapter, turn off the power of the projector and disconnect the power cord.

NOTE • Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device.

• Some input ports are selectable in the use.

• Be careful not to mistakenly connect a connector to a wrong port.

Ferrite core for HDMI cable

When connecting a HDMI cable to this projector, attach the ferrite core that is

supplied with the projector to the HDMI cable.

Refer to the following gure to attach the core to the cable nearby one end of the

cable rmly, and secure it using the accessory core band.

Be sure to connect the end of the cable to the projector.

Ferrite core

Band

Ferrite core HDMI cable

Projector

HDMI1

HDMI2

HDMI

WARNING ►Keep small parts away from children and pets. Take care not

to put in the mouth.

►Heat may build up in the USB wireless adapter, to avoid possible burns

disconnect the projector power cord for 10 minutes before touching the adapter.

Tab

Fastening the adapter cover

When using the USB wireless adapter, use the supplied adapter cover to avoid

possible burns.

USB wireless adapter: USB-WL-11N

Temperature range: 0 ~ 45 °C (Operating)

Loosen the screw on the bottom left of the WIRELESS port.

2. Insert the tab of the cover into the hole at the upper right of the WIRELESS

port in the direction of the arrow.

3. Align the screw holes on the projector and the cover. Then insert the screw

removed from the projector into the hole and tighten the screw.

ENGLISH

WARNING ►Do not connect the projector to a power supply while no lens

unit is attached to it.

►Use extra caution when connecting the power cord, as incorrect or faulty

connections may result in  re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible.

Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in  re, electric

shock or other accidents.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal

of the building using an appropriate power cord (bundled).

NOTICE ►This product is also designed for IT power systems with a phase-

to-phase voltage of 220 to 240 V.

Connecting power supply

1. Insert the connector of the power cord into the AC (AC inlet) of the projector.

Firmly plug the power cord’s plug into the outlet. In a couple of seconds after

the power supply connection, the POWER indicator will light up in steady

orange.

Remember that when the DIRECT POWER ON function activated, the connection of

the power supply make the projector turn on.

Power cord

WARNING

►Do not use

tied power cord.

Turning on the power

1. Make sure that the power cord is rmly and correctly connected to the

projector and the outlet.

2. Make sure that the POWER indicator is lighted in steady orange.

3. Press the STANDBY/ON button on the projector or the ON button on the

remote control.

The projection lamp will light up and the POWER indicator will begin blinking in

green. When the power is completely on, the indicator will stop blinking and light

in steady green.

WARNING ►A strong light is emitted when the projector’s power is on. Do

not look into the lens of the projector or look inside of the projector through any

of the projector’s openings, since the projection ray may cause a trouble on

your eyes.

►Blocking the beam by something causes high temperature and could result in

re or smoke.

NOTE • Power on the projector prior to any connected devices.

• The projector has the DIRECT POWER ON function, which makes the

projector automatically turn on.

POWER

indicator

ON button

STANDBY/ON

button

Autres manuels pour CP-WU9100

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Projecteur

Hitachi

Hitachi ED-X24 and Document technique

Hitachi

Hitachi FT-01 Manuel utilisateur

Hitachi

Hitachi CP-X4021N Document technique

Hitachi

Hitachi IPJ-AW250N Instructions d'installation et d'entretien

Hitachi

Hitachi PJLC2001 Manuel utilisateur

Hitachi

Hitachi CP-S220W Manuel utilisateur

Hitachi

Hitachi CP-S225 Manuel utilisateur

Hitachi

Hitachi CP-X2 series Mode d’emploi

Hitachi

Hitachi CP-DW10N Manuel utilisateur

Hitachi

Hitachi ED-A110 Manuel utilisateur

Hitachi

Hitachi CP-X8170 Manuel utilisateur

Hitachi

Hitachi CP-X380W Manuel d'utilisation et d'entretien

Hitachi

Hitachi CP-AW250NM Manuel utilisateur

Hitachi

Hitachi CP-WX625 Manuel utilisateur

Hitachi

Hitachi CP-X960WE Manuel utilisateur

Hitachi

Hitachi CP-X608 Manuel utilisateur

Hitachi

Hitachi CPX4 series Manuel utilisateur

Hitachi

Hitachi CP-RX82 Manuel utilisateur

Hitachi

Hitachi CP-WX1100 Manuel d'utilisation et d'entretien

Hitachi

Hitachi CP-RX79 Manuel utilisateur

Hitachi

Hitachi CP-RX80W Manuel utilisateur

Hitachi

Hitachi CP-X445 Manuel utilisateur

Hitachi

Hitachi CP-X4021N Manuel utilisateur

Hitachi

Hitachi Innovate CP-RX94 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur