Hitachi DZ-BD10H Manuel utilisateur

Quick Operation

(English)

DZ-BD10H

Quick Operation (English)

Setting up the battery pack

Removing the battery pack

Charging status CHARGE indicator

During charge Lit

Charge complete Unlit

Note

Charging will not occur if the DC

power cord is connected.

After charging is complete, attach the battery pack to the camcorder.

If the CHARGE indicator does not light,

check that the connections ( , ,

and ) are firmly made.

CHARGE

indicator

Terminal at bottom

Always turn the power off before disconnecting

the power supply.

While pressing and holding the BATT switch,

slide the battery pack upward, then remove it.

• Be careful not to drop the battery pack

while detaching it.

Quick Operation (English)

Changing the display language

(LANGUAGE)

You can change the language used on screens and menus.

The following shows how to change from Japanese to English.

Turn on the power.

Press the menu button, then select " 初期設定 " by pressing f/e.

Then, press c(or the confirmation button).

Setting the Date and Time

Press the menu button, then select "Date Setup" by pressing f/e.

Then, press cto select "Date Set" and press the confirmation button.

Select each item by pressing d/cand set the correct value by pressing f/e.

• Repeat this step until year, month, date, hour,

minute, and AM/PM are correctly set.

Press the confirmation button.

The confirmation screen appears.

Press dto select "YES", then press the

confirmation button to confirm.

• If you select “No” and press the confirmation button, the screen returns to

step .

Confirmation button

Menu button

Cancel/Stop

button

Press and hold the lock button, and

turn the power switch to " 入".

Select " 言語切替 " by pressing f/

e, then press c(or the

confirmation button).

Select "English" by pressing e,

then press the confirmation button.

ೋᦼ⸳ቯ

࿗

ࠨ೰

ᠲ૞㖸

ࡄࡢ࡯࠮࡯ࡉ

㍳↹࡜ࡦࡊ

⸒⺆ಾᦧ

࠺ࡕࡕ࡯࠼

⸳ቯ࡝࠮࠶࠻

ᣣᧄ⺆

'PINKUJ

ೋᦼ⸳ቯ

࿗

ࠨ೰

ᠲ૞㖸

ࡄࡢ࡯࠮࡯ࡉ

㍳↹࡜ࡦࡊ

⸒⺆ಾᦧ

࠺ࡕࡕ࡯࠼

⸳ቯ࡝࠮࠶࠻

ᣣᧄ⺆

ࠝࡦ

ࠝ࡯࠻

ࠝࡦ

ࠝࡈ

ŅŢŵŦġŔŦŵ

ĳııĹ İġĲıġİġġġĲġġġ

łŎ

ġġĲıȇıı

ńŉłŏňņ ŎŐŗņ ņŏŕņœ œņŕŖœŏ

Quick Operation (English)

Inserting a BD or DVD

Close the lid.

After the lid is closed all the way, the camcorder will attempt to recognize the

BD/DVD. During this recognition process, the access indicator flashes. While

this is happening, do not remove the power source, shake the camcorder, or

subject it to impact.

When a new BD-RE/BD-R/DVD-RW is loaded, the format confirmation screen will

appear. See p.4.

Attach the charged battery pack to the

camcorder, or connect the camcorder

to a power outlet.

Turn the power switch to " 切" (Off),

then press up the disc eject switch until

the access indicator lights, then

release.

After several seconds, the lid pops

open. Open it fully with your hand.

Place the recording surface of the BD/

DVD face down, then push down on the

center of the BD/DVD until it clicks into

place.

• For single-sided discs, the side

opposite the label is the recording

surface.

• To record on the other side for

double-sided discs, remove the

disc (p.4), flip it over, and then

reload it.

Notes

• The disc mechanism may be quite hot immediately after use. Do not touch the metallic areas.

• Do not peer into the pickup. Doing so may cause damage to your

eyesight.

• To prevent malfunction, never do any of the following:

– touch the laser pickup

– insert a disc that is not compatible with the camcorder

– close the lid before setting the disc securely into place

• The power automatically turns off if the lid is left open for approx.

three minutes while the power switch is set to “ 切” (Off).

• The lid will not open if the camcorder is not connected to a power

source.

Pickup

Quick Operation (English)

When loading a new BD-RE/BD-R/DVD-RW

The disc must be formatted before it can be used for recording. When the disc is loaded, the

format confirmation screen will appear in the LCD monitor.

Open the LCD monitor.

Select "YES" by pressing d, then press the confirmation button.

• When using a BD-RE/BD-R, formatting will start. Skip step .

• When using a DVD-RW, proceed to step .

(When using a DVD-RW)

The recording format selection screen appears.

Select “VR Mode” or “VF Mode” by pressing d

c, then press the

confirmation button.

Removing the BD/DVD

Pressing slightly on the center hub with a

finger, grip the edge of the disc with your

thumb and lift the disc out as shown.

／

Note

Be careful that the power is not

accidentally cut off while formatting,

otherwise, the disc will become unusable.

Confirmation button

VR Mode

After recording, you can perform

various editing functions, such as

choosing or deleting scenes. You

can play back the disc in a device

that supports an 8cm DVD-RW

(VR Mode) after finalizing the disc.

VF (Video) Mode

Although editing cannot be done on

the camcorder, you can play back the

disc on other DVD devices after

finalizing the disc.

Quick Operation (English)

Inserting and Removing Card

Recording Movies/Still Pictures

You can record movies to HDD/BD/DVD/SD card and still pictures to SD card.

Always turn off the power before

inserting a card.

Open the cover.

Push the card in until it clicks into place.

(To remove the card, push it in slightly

and release. The card will pop up, and

you can remove it.)

Always close the cover.

Pay attention to the orientation of the

card. The terminals should face the cover.

HDD BD-R RAM -RW (VR) R

-RW (VF)

BD-RE CARD

Press and hold the lock button to turn

the power switch to "

入

1To record movies, slide the Movie/Stills switch to " ".

To record stills, slide the Movie/Stills switch to " ".

3Turn the power switch to "

入

" (On).

The HDD indicator lights and the camcorder enters recording pause

mode.

･To turn off the camcorder, turn it to " 切" (Off).

(Only when you have set the Movie/Stills switch to

"".)

To switch between HDD, BD/DVD, and SD card, turn the

power switch to "

メディア

" and release it repeatedly.

2Open the LCD monitor.

Quick Operation (English)

4Press the record button.

･"m" (recording pause) in the LCD monitor

will change to "n" and recording will

begin.

The recording indicator beneath the lens will

also light up red.

･To pause recording, press the record button

again. The elapsed recording time will reset to

"0:00:00".

･To resume recording, press the record button

again.

2008/10/ 1

Remaining battery

level

Current time

Elapsed recording time

(hrs : mins : secs)

Remaining space on

HDD/BD/DVD/Card

m／n

4Press the "フォト "(photo) button halfway down.

A subject will be focused. When focus is locked, the green "m"in

the LCD monitor will turn purple.

5Fully press the "フォト "(photo) button.

The image will be recorded. After a few seconds, the image shot will

be displayed for about three seconds. You can shoot the next photo

when "m" changes back to green.

When you have set the Movie/Stills switch to

" " (movie)...

When you have set the Movie/Stills switch to

" " (stills)...

Quick Operation (English)

Playback

Choosing and playing back a scene

Press the Disc Navigation button while the media you want to play back is in

recording pause mode.

The scenes thumbnails appear on the disc navigation screen.

Choose a scene by pressing f/e(up/down, previous page/following page) and

d/c(left/right).

Press the confirmation button.

The chosen scene is played back.

• To promptly return to the disc navigation screen, press Cor the Disc

Navigation button. To return to recording pause mode, press Cor the Disc

Navigation button again.

Adjusting speaker volume during movie playback

Confirmation/Play/Pause

button／／／／

Menu button



(Stop/Cancel)

button

Movie/Picture

(also referred as

scene) selection

button

“見る” (Disc Navigation) button

HDD BD-R RAM -RW (VR) R

-RW (VF) CARD

BD-RE

HDD BD-R RAM -RW (VR) R

-RW (VF) CARDBD-RE

Increase the volume

Decrease the volume

Table des matières

Autres manuels Hitachi Appareil photo numérique

Hitachi

Hitachi MPEGCAM MP-EG1A Manuel utilisateur

Hitachi

Hitachi HDC-881E Manuel utilisateur

Hitachi

Hitachi HDC-1097E Manuel utilisateur

Hitachi

Hitachi VME535LE Manuel utilisateur

Hitachi

Hitachi HV-HD33 Manuel utilisateur

Hitachi

Hitachi GigE Manuel utilisateur

Hitachi

Hitachi HDC-891E Manuel utilisateur

Hitachi

Hitachi KP-M1E/K Manuel utilisateur

Hitachi

Hitachi Z-3000W Manuel utilisateur

Hitachi

Hitachi HDC-1296ER Manuel utilisateur

Hitachi

Hitachi HDC-88WE Manuel utilisateur

Hitachi

Hitachi HDC-401EX Manuel utilisateur

Hitachi

Hitachi SK-HD1300-S1 Manuel utilisateur

Hitachi

Hitachi HDC-1086E Manuel utilisateur

Hitachi

Hitachi HDC-561E Manuel utilisateur

Hitachi

Hitachi HDC-761E Manuel utilisateur

Hitachi

Hitachi HDC-886E Manuel utilisateur

Hitachi

Hitachi HDC-1087E Manuel utilisateur

Hitachi

Hitachi V-21W Manuel utilisateur

Hitachi

Hitachi VZ-HD3600A Manuel utilisateur

Hitachi

Hitachi KP-FM200WCL Manuel utilisateur

Hitachi

Hitachi HDC-887E Manuel utilisateur

Hitachi

Hitachi HDC-651E Manuel utilisateur

Hitachi

Hitachi KP-HD20A Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur