Hioki 3196 Manuel utilisateur
Case Studies of
Power Quality Surveys
using
Model 3196 Power Quality Analyzer
HIOKI E.E. CORPORATION
July 2005
Rev. 5
TABLE OF CONTENTS
Power Quality Basics: Current Power Supply Environment Page 1
Power Quality Standards Page 1
Main Power Quality Parameters Page 2 to 4
Case Study 1: Inrush Current and Current RMS Value of a Dryer Page 5 to 6
Case Study 2:
Switching of Power Factor Improvement
Capacitor
Page 7 to 8
Case Study 3:
Voltage Dip (Instantaneous Voltage Drop
- at Receptacle
Page 9 to 10
Case Study 4:
Voltage Dip (Instantaneous Voltage Drop)
- at Distribution Panel
Page 11
Case Study 5:
Transient Overvoltage
Page 12 to 13
Case Study 6:
Periodical Instantaneous Voltage Drop
Page 14
Case Study 7:
General UPS Switching Waveform
Page 15
Case Study 8: Page 16
Case Study 9: Page 17
Case Study 10: Voltage Waveform Noise & UPS Switching Page 18 to 19
Appendix: Power Quality Survey Procedures Page 27 to 28
Case Study 11:
Case Study 12:
Voltage Dip in a Factory
Inflow and Outflow of Harmonics
Voltage Drop Caused by Wiring Impedance
Transients Caused by Glow Fluorescent Lighting
Page 20 to 22
Page 23 to 26
- page 1 -
Power Quality Basics
Current Power Supply Environment
Power Quality Standards
Various factors can contribute to worsening power quality
International
Power Quality
Deterioration
Open market
Tough competition to
cut costs
Increase use of PCs
and inverter devices
Connection with new
energy sources (wind,
solar, gas turbine, etc.)
Connection with on-
site power supply
Connection
mixes the
different
power
characteristics
Europe
U.S.A.
Standard Title Published Comment
IEC
61000-4-7
IEC
61000-4-15
IEC
61000-4-30
EN50160
IEEE 1159
IEEE 519
IEEE 446
ANSI C84.1
General guide on harmonics and inter-
harmonics measurements and
instrumentation, for power supply systems
and equipment connected thereto
1991
2002 revised
Actualization of inter-
harmonic concept (from
revision)
Flicker meter - Functional and design
specifications
Testing and measurement techniques
Power Quality measurement methods
1997
2003 A1
2003
120V/60Hz added in
amendment
New standard
Standard Title Published Comment
Standard Title Published Comment
Voltage Characteristics of electricity
supplied by public distribution systems
1995,
1999 revised
General power quality
standard
IEEE Recommended Practice for
Monitoring Electric Power Quality
IEEE Recommended Practice and
Requirements
IEEE Recommended Practice for
Emergency and Standby Power Systems
for Industrial and Commercial Applications
Electrical Power Systems and Equipment -
Voltage Ratings (60Hz)
1995
1992
1995
1995
Anomaly voltage
Classification of basic
terms
Standards for harmonic
limit values
Describes the CBEMA
curve
Voltage limit values
- page 2 -
ITIC (CBEMA) curve
The ITIC curve judges the allowable level of
voltage RMS fluctuation from the voltage swell,
voltage dip and interruption events.
The analysis is made by the period and depth of
each event according to the limit value of the ITIC
curve.
The ITIC (Information Technology Industry
Council) curve is the most recent version of the
older CBEMA (Computer and Business
Equipment Manufacturers Association) curve.
Both were created by CBEMA. The original
CBEMA curve was widely used in the U.S.A.
Main Power Quality Parameters
1. Transient overvoltage (impulse)
1) Phenomenon
Radical changes in voltage with high voltage
peaks
2) Cause
3) Damage
4) Analysis
Lightning strikes
Power circuit switching
Closure of inductive circuits
Arc to the ground
Load switching
Contact of a bouncing relay
Destruction of power supplies of
equipment
Equipment reset
Waveform (Maximum voltage level, Rise
time, Phase angle, Fluctuation,
Repeatability)
The faster rise time means a closer
occurring point.
2. Voltage Dip
1) Phenomenon
Instantaneous drop of RMS voltage
2) Cause
3) Damage
Large inrush current by turning on heavy
loads
Accident in the distribution network
(Lightning, snow, ice, contact of birds/
trees, effects of accidents)
Short-circuit
Stop or equipment reset
- page 3 -
3. Voltage Swell
1) Phenomenon
Instantaneous rise of RMS voltage
2) Cause
3) Damage
Lightning strikes
Introducing heavy loads
Destruction of power supplies in
equipment
4. Instantaneous Interruptions
1) Phenomenon
Instantaneous or short/long term power
outage
2) Cause
3) Damage
Accident on distribution network
(Lightning, snow, ice, contact of birds/
trees, effects of accidents)
Short-circuit
Stop or equipment reset
5. Unbalance Factor
1) Phenomenon
Imbalance of each phase in 3-phase system
2) Cause
3) Damage
Imbalance of loads by 1-phase load
connection (especially long distribution
lines)
Transformer capacity difference at
receptacle
Overheating of a 3-phase inductive motor
or transformer
Stop equipment by 3E relay tripping (over-
current, missing phase, reverse-phase)
Uneven motor rotation
6. Harmonics
1) Phenomenon
Voltage or current waveform distortion
2) Cause
3) Damage
Thyristor powered conversion devices
Inverter, Variable frequency drives
Overheating, burning, abnormal sounds or
vibration sound caused by the inflow of
harmonic current to the equipment
Malfunctions due to the harmonics voltage
(overheating or burning of reactor for
phase advancing capacitor)
7. Flicker
1) Phenomenon
Regularly repeated voltage impulses spanning
one or more cycles which cause flicker in the
lighting device
2) Cause
3) Damage
Arc/blast furnaces
Arc welding
Flicker in the lighting device
Equipment malfunction
- page 4 -
- page 5 -
CASE STUDY 1
Inrush Current and Current RMS Value of an Industrial Dryer
Environment:
Problem:
Analysis:
Target: 1-phase 2-wire, 100V circuit
This is a simple simulation example.
By using an industrial dryer (100V
AC, 1kW, 50/60Hz), the RMS
fluctuation and inrush current are
measured while switching the dryer
from "OFF=>ON=>COLD=>OFF."
Note:
Model 9694 Clamp on Sensor is
clamped to the 10-turn coil with a CT
setting 0.1.
To record the inrush current event waveform, use the current peak event.
To record the waveform while the dryer is continuously operating in HOT, using themanual event
([ESC]+[EVENT]) is effective.
Current RMS Value Fluctuation
OFF HOT HOTCOLD
The current value while a dryer is working is
10Arms, but the start-up current rises to
10.951Arms.
- page 6 -
Fluctuation of Current Waveform Peak (+) Fluctuation of Current Waveform Peak (-)
Fluctuation of Voltage RMS Value Fluctuation of Active Power RMS Value
A voltage drop of about 4Vrms is measured when the dryer is in operation.
The maximum power is 1.1071kW
Inrush Current Waveform
- page 7 -
CASE STUDY 2
Voltage Drop Caused by Wiring Impedance
Environment:
Problem:
Analysis:
Target: 1-phase 2-wire, 100V circuit
This is an easy simlulation similar to Case Study 1 to monitor the voltage drop caused by wiring
impedance. The voltage at a load shows the voltage drop to the supply side when the wire is thin
and long.
CH2
CH1
When switching an industrial dryer (100V
AC, 1kW, 50/60Hz) from OFF to HOT to
COLD and back to OFF, confirm the
difference in voltage drop between short
and long wirings.
1) When wiring is short
(low wiring impedance without the wires
circled in red)
2) When wiring is long
(high wiring impedance with wires circled in
red)
1) Short Wiring 2) Long Wiring
Voltage RMS Value Fluctuation
Voltage at power supply side
Voltage at consumption side
U1 (CH1: red) is the voltage not affected
by the wiring impedance.
U2 (CH2: green) is the voltage affected
by the wiring impedance.
By adding high wiring impedance, the
voltage drops for 6Vrms on the
consumption side.
The wiring impedance of the wires circled in
red is 0.6-Ohm.
The voltage drop is calculated by using the
Ohm's Law such that "0.6-Ohm x 10A =
6Vrms."
6Vrms
- page 8 -
1) Short Wiring 2) Long Wiring
Current RMS Value Fluctuation
1) Short Wiring 2) Long Wiring
Current Peak Value Fluctuation
In this dryer example, the current consumption at a load is slightly reduced when the wirng is long.
The dryer is a resistive load, so that the current consumption, which means the power consumption,
is reduced by the voltage drop.
If a constant power controlled load is connected, the power consumption is stable despite the
voltage drop. Therefore, the current consumption increases.
When HOT When HOT
When HOT When HOT
Autres manuels pour 3196
3
Table des matières
Autres manuels Hioki Instrument de mesure
Hioki
Hioki PW3365-20 Manuel utilisateur
Hioki
Hioki PW3390 Manuel utilisateur
Hioki
Hioki IM7585 Series Manuel d'utilisation et d'entretien
Hioki
Hioki MR8847-51 Manuel utilisateur
Hioki
Hioki DM7275 Series Manuel utilisateur
Hioki
Hioki 9290-10 Manuel utilisateur
Hioki
Hioki 2331-20 Manuel utilisateur
Hioki
Hioki FT3424 Manuel utilisateur
Hioki
Hioki MR8740T Manuel d'instructions
Hioki
Hioki FT3432 Manuel utilisateur
Hioki
Hioki MR8880-20 Manuel utilisateur
Hioki
Hioki 3280-10F Manuel utilisateur
Hioki
Hioki DSM-8542 Manuel utilisateur
Hioki
Hioki PQ3198 Manuel utilisateur
Hioki
Hioki CT7631 Manuel utilisateur
Hioki
Hioki CM4141 Manuel utilisateur
Hioki
Hioki 3280-10F Manuel utilisateur
Hioki
Hioki IM3523A Guide de l'utilisateur
Hioki
Hioki 8847 Manuel utilisateur
Hioki
Hioki TM6102 Manuel d'utilisation et d'entretien
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur