Hioki 3640-20 Manuel utilisateur

INSTRUCTION MANUAL

For...は専用機種。複数の場合は「/」で区切る。

不要の場合はとる。

形名を入力。複数の場合は「/」で区切る。

3640-20

品名を入力。

LUX LOGGER

Contents

Introduction i

Inspection ii

Safety Notes iii

Notes on Use v

Measurement Flow Chart and Reference Guide vi

Chapter 1 Product Overview 1

1.1 Name and Functions of Parts 2

1.2 Interval and Maximum Recording Time 3

Chapter 2 Set Up 5

2.1 Replacing the Battery 5

2.2 Power Save Function 7

2.3 Setting Current Time 8

2.4 Connecting 9662 LUX SENSOR 9

Chapter 3 Settings 11

3.1 Setting Items 11

3.2 Manual Setting 14

3.3 Setting by COMMUNICATION BASE 16

Chapter 4 Specifications 19

Chapter 5 Reference 21

5.1 Recommended Levels of Illumination 21

5.2 Relative Spectral Response Characteristics

in the Visible Spectrum 23

5.3 Angled Incident Light Characteristics 24

Chapter 6 Maintenance and Service 25

_____________________________________________________________________

Introduction

______________________________________________________________

Introduction

Thank you for purchasing this HIOKI "3640-20 LUX

LOGGER." To get the maximum performance from the

unit, please read this manual first, and keep this at hand.

_____________________________________________________________________

Inspection

______________________________________________________________

NOTE Testing monitor batteries installed in the unit may possibly be

weak. Replace batteries before extended measurement usage.

Ins

ection

When the unit is delivered, check and make sure that it has

not been damaged in transit. If the unit is damaged, or fails

to operate according to the specifications, contact your

dealer or HIOKI representative.

Accessories

9662 LUX SENSOR

Instruction Manual

LR03 alkaline battery X4 (built into this unit, for monitor)

Before using the product the first time, verify that it

operates normally to ensure that the no damage occurred

during storage or shipping. If you find any damage, contact

your dealer or Hioki representative.

iii

_____________________________________________________________________

Safety Notes

______________________________________________________________

DANGE

This equipment is designed according to IEC 61010-1

Safety Standards, and has been tested for safety prior

to shipment. Incorrect measurement procedures

could result in injury or death, as well as damage to

the equipment. Please read this manual carefully and

be sure that you understand its contents before using

the equipment. The manufacturer disclaims all

responsibility for any accident or injury except that

resulting due to defect in its product.

Safety Symbols

This symbol is affixed to locations on the equipment

where the operator should consult corresponding topics

in this manual (which are also marked with the

symbol) before using relevant functions of the

equipment.

In the manual, this mark indicates explanations which it

is particularly important that the user read before using

the equipment.

Indicates DC (Direct Current).

Safet

Notes

This Instruction Manual provides information and warnings

essential for operating this equipment in a safe manner and

for maintaining it in safe operating condition. Before using

this equipment, be sure to carefully read the following

safety notes.

_____________________________________________________________________

Safety Notes

______________________________________________________________

DANGE

Indicates that incorrect operation presents extreme

danger of accident resulting in death or serious injury

to the user.

WARNING

Indicates that incorrect operation presents significant

danger of accident resulting in death or serious injury

to the user.

CAUTION Indicates that incorrect operation presents possibility

of injury to the user or damage to the equipment.

NOTE Denotes items of advice related to performance of the

equipment or to its correct operation.

f.s. (maximum display or scale value, or length of scale)

Signifies the maximum display (scale) value or the length

of the scale (in cases where the scale consists of unequal

increments or where the maximum value cannot be

defined).

In general, this is the range value (the value written on

the range selector or equivalent) currently in use.

rdg. (displayed or indicated value)

This signifies the value actually being measured, i.e., the

value that is currently indicated or displayed by the

measuring instrument.

dgt. (resolution)

Signifies the smallest display unit on a digital measuring

instrument, i.e., the value displayed when the last digit on

the digital display is "1".

The following symbols are used in this Instruction Manual

to indicate the relative importance of cautions and

warnings.

Accuracy

The specifications in this manual include figures for

"measurement accuracy" when referring to digital

measuring instruments, and for "measurement tolerance"

when referring to analog instruments.

_____________________________________________________________________

Notes on Use

______________________________________________________________

CAUTION Do not store or use the product where it could be exposed

to high temperature or humidity, or condensation. Under

such conditions, the product may be damaged and

insulation may deteriorate so that it no longer meets

specifications.

NOTE Attach the supplied light sensor cap to the detector and then

perform zero ajustment before measurement.

Do not store or use the tester where it will be exposed to direct

sunlight, high temperature, high humidity, or condensation. If

exposed to such conditions, the tester may be damaged, the

insulation may deteriorate, and the tester may no longer satisfy

its specifications.

The reference level as marked on the faceplate is the tip of the

light sensor.

Notes on Use

In order to ensure safe operation and to obtain maximum

performance from the unit, observe the cautions listed

below.

_____________________________________________________________________

Measurement Flow Chart and Reference Guide

______________________________________________________________

Is there sufficient

battery charge remaining

to o

erate 3640-20?

Replace batteries

Setting current time

See 2.1.

Connecting sensor See 2.4.

Set current time when using 3640-20 for the

first time or re

lacin

batteries. See 2.3.

Zero ajustment See 2.4.

Setting 3640-20

stand-alone

・Interval

・Range

Setting 3640-20

with COMMUNICATION

BASE

・Interval

・Current time

・Start control

・Recording method

Setting 3640-20 with

COMMUNICATION BASE

and PC

・Interval ・Current time

・Start control ・Range

・Recording method

・Comment

See 3.2.

Press REC/STOP

button to start

measurement.

Settin

start control

Start control o

tions

Yes

Quick start

Prescheduled start

Starts measurement

immediately.

Starts measurement at

prescheduled time.

Setting

recordin

method

Endless

One time

When recording data

reaches 32000

measurement stops.

When recording data exceeds 32000, it overwrites

previously recorded data.

Press REC/STOP button to stop measurement.

After measurement is complete, disconnect sensor. Use COMMUNICATION BASE to

send measurement data to personal computer. (See COMMUNICATION BASE

instruction manual.)

See 3.2.

Measurement Flow Chart and Reference Guide

Table des matières

Autres manuels Hioki Enregistreur de données

Hioki

Hioki PW3365 Manuel utilisateur

Hioki

Hioki 3639-20 Manuel utilisateur

Hioki

Hioki LR8431-20 Manuel utilisateur

Hioki

Hioki lr5001 Manuel utilisateur

Hioki

Hioki 3638-20 Manuel utilisateur

Hioki

Hioki LR8450 Manuel utilisateur

Hioki

Hioki LR8512 Manuel utilisateur

Hioki

Hioki 3645-20 Manuel utilisateur

Hioki

Hioki LR8431-20 Manuel utilisateur

Hioki

Hioki LR8450 Manuel d'instructions

Hioki

Hioki LR8431-20 Manuel utilisateur

Hioki

Hioki HiLogger 3145-20 Manuel utilisateur

Hioki

Hioki HiCORDER MR8880 Manuel utilisateur

Hioki

Hioki lr5001 Manuel utilisateur

Hioki

Hioki 8423 Manuel utilisateur

Hioki

Hioki HiLogger 3145-20 Manuel utilisateur

Hioki

Hioki LR8400-20 Manuel utilisateur

Hioki

Hioki LR8512 Manuel utilisateur

Hioki

Hioki LR8450 Manuel d'instructions

Hioki

Hioki LR5051 Manuel utilisateur

Hioki

Hioki LR8101 Guide de l'utilisateur

Hioki

Hioki 8861 Manuel d'instructions

Hioki

Hioki LR5051-20 Manuel utilisateur

Hioki

Hioki LR8450 Manuel utilisateur

Manuels Enregistreur de données populaires d'autres marques

TESTO

TESTO 176 Manuel utilisateur

HT Italia

HT Italia XL421 Manuel utilisateur

HBM

HBM SOMAT XR CX22B-R Manuel utilisateur

Agtrix

Agtrix 380i Manuel utilisateur

Hobo

Hobo H8 Pro Manuel utilisateur

Beijing ART Tech

Beijing ART Tech PCI2320 Manuel utilisateur

Athena

Athena GET SL1 Manuel utilisateur

Motec Systems

Motec Systems C185 Manuel utilisateur

Beijing ART Tech

Beijing ART Tech USB2832 Manuel utilisateur

Rotronic

Rotronic HygroLog HL20 Manuel utilisateur

MRC

MRC DW-6092 Manuel utilisateur

Racelogic

Racelogic VBOX LapTimer Manuel utilisateur

Edu-Logger

Edu-Logger 900-240 Manuel utilisateur

Elma

Elma DT173 Manuel utilisateur

MadgeTech

MadgeTech PRTemp140 Fiche technique

Comet

Comet U0121M Manuel utilisateur

pico Technology

pico Technology PT-104 Manuel utilisateur

Soil Instruments

Soil Instruments GTecLink Manuel utilisateur