HIK VISION DS-2CD6D24FWD-IZHS Manuel utilisateur
EXIR Flexible
Network Camera
Quick Start Guide
COPYRIGHT © 2017 Hikvision. ALL RIGHTS RESERVED
Quick Start Guide
ALL RIGHTS RESERVED
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
This user manual (hereinafter referred to be “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or whol-
ly, by any means, without the prior written permission of Hikvision.
Unless otherwise stipulated, Hikvision does not make any warran-
ties, guarantees or representations, express or implied, regarding to
the Manual.
About this Manual
This Manual is applicable to EXIR Flexible Network Camera.
The Manual includes instructions for using and managing the prod-
uct. Pictures, charts, images and all other information hereinafter
are for description and explanation only. The information contained
in the Manual is subject to change, without notice, due to rmware
updates or other reasons. Please nd the latest version in the com-
pany website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are
the properties of Hikvision in various jurisdictions. Other trademarks
and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL
FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRAN-
TIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITA-
TION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS
FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF
THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR
ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR
LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE
USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR AB-
NORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAM-
AGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,
VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE
CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE
USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR
USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL
NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED
WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL
AND THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly ap-
proved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC compliance: This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interfer-
ence that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories
too are marked with "CE" and comply therefore withthe
applicable harmonized European standards listed under
the the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.
recyclethis.info
2006/66/EC and its amendment 2013/56/EU (battery
directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European
Union. See the product documentation for specic battery
information. The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards require-
ments.
Safety Instruction
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws, electrical
safety regulations, and re prevention regulations.
Transportation
Keep the device in original or similar packaging while transporting
it.
Power Supply
The input voltage should conform to IEC60950-1 standard: SELV
(Safety Extra Low Voltage) and the Limited Power Source. Refer to
the appropriate documentation for detailed information.
The standard power supply is 12 VDC, PoE (802.3at) or Hi-PoE,
please make sure your power supply matches with your camera.
DO NOT connect multiple devices to one power adapter, to avoid
over-heating or re hazards caused by overload.
Make sure the plug is properly connected to the power socket.
System Security
The installer and user are responsible for password and security
conguration and its settings.
Battery
Improper use or replacement of the battery may result in explosion
hazard. Replace with the same or equivalent type only. Dispose of
used batteries in conformance with the local codes.
Maintenance
If the product does not work properly, please contact your dealer or
the nearest service center. We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require
regular replacement. The average lifespan varies, so periodic
checking is recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside
surfaces of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens
is not exposed to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or dusty
environments.
Warnings
Serious injury or death may be caused if any of these warnings are
neglected.
Follow these safeguards to prevent serious injury or death.
Cautions
Cautions: Injury or equipment damage may be caused if any of
these cautions are neglected.
Follow these precautions to prevent potential injury or material
damage.
Warnings
For indoor-only device, place it in a dry and well-ventilated
environment.
Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the requirement of
the device. The operating humidity shall be 95% or less (non-
condensing), and the operating temperature is below:
Indoor device: -10°C to 40 °C (14 °F to 104 °F ),
Outdoor device: -30 °C to 60 °C (-22 °F to 140 °F), or -H model: -40
°C to 60 °C (-40 °F to 140 °F).
Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
IR Reection Prevention
Dust or grease on the dome cover will cause IR reection. Please
do not remove the dome cover lm until the installation is nished.
If there is dust or grease on the dome cover, clean the dome cover
with clean soft cloth and isopropyl alcohol.
Make sure that there is no reective surface too close to the camera
lens. The IR light from the camera may reflect back into the lens
causing reection.
The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring and
the dome cover are attached seamlessly.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off
the power, unplug the power cable, and contact the service center.
Time Synchronization
Set up camera time manually for the first time access if the local
time is not synchronized with that of the network. Visit the camera
via Web browse/client software and go to time settings interface.
Installation
Make sure the device is firmly secured to any wall or ceiling
mountings.
Be sure that there is enough space to install the camera and
accessories.
Make sure that the device in the package is in good condition and
all the assembly parts are included.
Make sure that the wall is strong enough to withstand at least 4
times the weight of the camera and the mount.
Make sure that the power has been disconnected before you wire,
install, or disassemble the device.
Symbols and Marks
Notice
Warning
Forbidden
Correct
Incorrect
Turn to page A and continue.
i. Not necessarily included accessory.
ii. Variable accessory amount.
iii. Skip this step if not required.
MicroSD card
Grounding
Disposal
Purchase separately
1x
1x 1x
1x
2x
1x
5.0
1x1x
T20
*
7x
1x 1x
*
P0SFM5×10-SUS
PA5×25-SUS316L
1
1.1
1.2
microSD
32
1.1
1.2
microSD
32
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels HIK VISION Caméra de sécurité
HIK VISION
HIK VISION HiLook THC-B129-LPS Manuel utilisateur
HIK VISION
HIK VISION DS-2CD7A85G0-IZHS Manuel utilisateur
HIK VISION
HIK VISION UD07275B Manuel utilisateur
HIK VISION
HIK VISION DS-2TD4136T-25 Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2763G0-IZS Manuel utilisateur
HIK VISION
HIK VISION DS-2DE5232W-AE3 Manuel utilisateur
HIK VISION
HIK VISION DS-2CD1043G0E-I Manuel utilisateur
HIK VISION
HIK VISION 5 Inch Network High Speed Dome Manuel utilisateur
HIK VISION
HIK VISION PIR Series Manuel utilisateur
HIK VISION
HIK VISION DS-2CD series Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2D21G0/M/NF Manuel utilisateur
HIK VISION
HIK VISION iDS-2VS435-F840-EY Manuel utilisateur
HIK VISION
HIK VISION DS-2DP1636Z-D Manuel utilisateur
HIK VISION
HIK VISION PanoVu PT Series Manuel utilisateur
HIK VISION
HIK VISION PTZ-N4225I-DE Manuel utilisateur
HIK VISION
HIK VISION HWI-T621H-Z Manuel utilisateur
HIK VISION
HIK VISION DS-2CD6425G0 Series Manuel utilisateur
HIK VISION
HIK VISION DS-2CE17H0T-IT3F Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2786G2T-IZS Manuel utilisateur
HIK VISION
HIK VISION DS-2CE16H5T-IT Manuel utilisateur
