HighPoint SSD7110 Manuel utilisateur
SSD7110 Controller Windows Installation Guide
1/9
SSD7110 Controller
Windows
Installation Guide
Version 1.2
Copyright © 2018 HighPoint Technologies, Inc.
All rights reserved.
SSD7110 Controller Windows Installation Guide
2/9
1 Overview
The purpose of this document is to provide clear instructions on how to install and use
SSD7110 Controller on Windows system.
2 Installing Windows on SSD7110 controller
If you would like to install Windows onto drives attached to SSD7110 controller, please
perform the following operations:
Step 1 Prepare Your Hardware for Installation
After you attach your NVMe SSD to SSD7110 controller, you can use SSD7110 UEFI Utility to
configure your NVMe SSD as RAID arrays, or just use them as single disks.
Before installation, you must remove all the disk drives, which are not physically attached to
SSD7110 controller, from your system.
Note
SSD7110 only support UEFI boot .If you have other SCSI adapters installed, you must make sure
the SSD7110 controller UEFI will be loaded firstly. If not, try to move it to another PCI slot.
Otherwise you may be unable to boot up your system.
Step 2 Check System UEFI Settings
Set UEFI setting with SuperMicro X11DAi-N motherboard as an example.
a. Set "Boot Mode Select" to "UEFI";
b. And "Advanced->PCIe/PCI/PnP Configuration->CPU Slot PCI-E OPROM" to "EFI".Suppose
SSD7110 Controller Windows Installation Guide
3/9
SSD7110 is connected to motherboard CPU1 Slot 1 PCI-E X16,then you should set "CPU1
Slot 1 PCI-E X16 OPROM" to "EFI";
c. Disable "Secure Boot", set "Attempt Secure Boot" to "Disabled".
Step 3 Flash UEFI Rom to SSD7110
a. Unzip SSD7110 UEFI package to root dir(/) of a USB flash driver,and insert the USB flash
drive to the motherboard;
b. Booting from the UEFI USB flash and enter the UEFI environment ;
c. Command with “SSD711x.nsh”, flash UEFI rom to SSD7110 Controller and reboot.
SSD7110 Controller Windows Installation Guide
4/9
Step 4 Create Array
a. Attach three NVMe SSD to SSD7110 Controller ;
Note
Make sure your USB flash partition format is NTFS or FAT32.
b. Boot, in the presence of the motherboard Log screen, there will be NVMe SSD
information：
c. Enter the motherboard’s Boot List and select start from UEFI USB flash:
d. Command ”mode”, ”mode 160 53” to change the resolution:
SSD7110 Controller Windows Installation Guide
5/9
e. Command ”Arraycreate.efi” to enter the Utility:
f. Command ”create RAID0 ”.
Create RAID0 array with all disks and with maximum capacity.
g. Command “exit”；
h. For more command usages, refer to Appendix A.
Step 5 Install Windows
a. Put the Windows install DVD in your CD-ROM and then reboot your sysytem;
b. Boot, view RAID information that appears on the motherboard Logo screen:
SSD7110 Controller Windows Installation Guide
6/9
c. Enter Boot list, select start from UEFI DVD:
d. Install Windows, to “Where do you want to install Windows?”, you can see three Legacy
disk:
e. Click “Loader driver”，in the pup-up window, click “Cancel”:
SSD7110 Controller Windows Installation Guide
7/9
f. Uncheck "Hide drivers that aren't compatible with this computer's hardware":
g. Then plug the USB flash with the driver file onto the USB interface of the motherboard, click
“Browse”, select the driver file:
SSD7110 Controller Windows Installation Guide
8/9
h. After load the driver, back to “Where do you want to install Windows?” interface, the three
Legacy disk have become RAID partitions. For windows server, it will prompt “Windows
Can’t be installed on this driver.”,you should click this point and click OK.
i. After partitioning, continue installing and complete the installation of the Windows.
j. After the Windows is installed,please get into Windows and turn off Hibernation.
Hibernation fails when the system is installed on a NVMe RAID, this bug will affet fast
startup and sleep.Please use administrator privileges to turn off hibernation with the
following command in cmd:
#powercfg /h off
Appendix A
Support command: help/info/quit/exit/create/delete.
Create Command
Syntax
Create Array Type (RAID0/RAID1/RAID5) Member Disk list (1/1,1/2|*)Capacity(100|*)
Examples
<<< create RAID0
<<< create RAID0 *
<<< create RAID0 * *
Create RAID0 array with all disks and with maximum capacity.
<<< create RAID1 1/1, 1/3 10
Create RAID1 array with disk 1/1 and 1/3 and with 10GB capacity.
<<< create RAID5 * 40
Create RAID5 array with all disk and with 40GB capacity.
<<< create RAID5 1/1, 1/2,1/3 50
Create RAID5 array with disk 1/1, 1/2, and 1/3 and with 50GB capacity.
SSD7110 Controller Windows Installation Guide
9/9
Delete Command
Syntax
delete {array ID}
Examples
<<< delete 1
Delete the first array from Logical device list.
<<< delete 2
Delete the second array from Logical device list.
Info Command
Syntax
info
Display physical device list and logical list
Exit Command
Syntax
Q/q/quit/exit
Quit the application
Help Command
Syntax
H/h/help
This is help message.
Autres manuels pour SSD7110
3
Table des matières
Autres manuels HighPoint Contrôleurs
HighPoint
HighPoint HPT366 Guide d'installation et d'utilisation
HighPoint
HighPoint Rocket 620 Manuel utilisateur
HighPoint
HighPoint ATA-133 RAID Manuel utilisateur
HighPoint
HighPoint SSD7110 Feuille d'instructions
HighPoint
HighPoint RocketRAID 2711 Manuel utilisateur
HighPoint
HighPoint RocketRAID 644L Manuel utilisateur
HighPoint
HighPoint SSD7505 Manuel utilisateur
HighPoint
HighPoint SSD7105 Manuel utilisateur
HighPoint
HighPoint RocketRAID mini SAS 3G HBA Series Manuel utilisateur
HighPoint
HighPoint SSD7180 Manuel utilisateur
HighPoint
HighPoint RocketRAID eSATA 6G series Manuel utilisateur
HighPoint
HighPoint RR2720A Manuel utilisateur
HighPoint
HighPoint RocketU Quad USB3.0 Manuel utilisateur
HighPoint
HighPoint RocketRAID 174x Manuel utilisateur
HighPoint
HighPoint RocketRAID 272 Series Manuel utilisateur
HighPoint
HighPoint Rocket 700L Series Manuel utilisateur
HighPoint
HighPoint RR640L Manuel utilisateur
HighPoint
HighPoint Rocket 710L Manuel utilisateur
HighPoint
HighPoint SSD6202A Manuel utilisateur
HighPoint
HighPoint RR64 L Series Manuel utilisateur
