HID VertX EVO V1000 Manuel utilisateur

VertX EVO V1000

Installation Guide

71000-901, Rev. A.4

July 2016

hidglobal.com

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Page 2 of 25 July 2016

form without the prior written permission of HID Global Corporation.

Trademarks

HID GLOBAL, HID, the HID logo, and VertX are the trademarks or registered trademarks of

HID Global Corporation, or its licensors, in the U.S. and other countries.

Revision History

Date

Description

Version

July 2016 Update to Section 3.4, wiring warning. A.4

February 2016 Update Global Contacts information and Section 5.1.3.1, password

configuration information. A.3

September 2012 Update Discovery GUI and Virtual Port, Section 2 A.2

July 2011 VertX Installation minus modem A.1

Contacts

For additional offices around the world, see www.hidglobal.com corporate offices.

North America Asia Pacific

611 Center Ridge Drive

Austin, TX 78753

USA

Phone: 866-607-7339

Fax: 949-732-2120

19/F 625 King’s Road

North Point, Island East

Hong Kong

Phone: 852 3160 9833

Fax: 852 3160 4809

Europe, Middle East and Africa Brazil

Haverhill Business Park Phoenix Road

Haverhill, Suffolk CB9 7AE

England

Phone: 44 (0) 1440 711 822

Fax: 44 (0) 1440 714 840

Condomínio Business Center

Av. Ermano Marchetti, 1435

Galpão A2 CEP 05038-001

Lapa - São Paulo/SP

Brazil

Phone: 55 11 5514-7100

HID Global Customer Support: www.hidglobal.com/support

July 2016 Page 3 of 25

see

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Contents

1Introduction..................................................................................................................................4

1.1 Parts List ................................................................................................................................................. 4

1.2 Product Specifications...................................................................................................................... 4

1.3 Cable Specifications............................................................................................................................5

2Overview……………………………………………………………………………………………………………………….6

3Connect…………………………………………………………………………………………………………………………7

3.1 What you need before getting started.......................................................................................7

3.2 V1000........................................................................................................................................................7

3.3 Mounting Instructions ........................................................................................................................7

3.4 Wiring VertX EVO................................................................................................................................8

4Contact…………………………………………………………………………………………………………………………12

4.1 Discovery GUI (for DHCP networks) ......................................................................................... 12

4.2 Virtual Port............................................................................................................................................ 12

5Configure……………………………………………………………………………………………………………………..13

5.1 VertX Communications.................................................................................................................... 13

5.1.1 Configuration GUI Login.................................................................................................. 13

5.1.2 Basic Network Setup......................................................................................................... 13

5.1.3 Host Communication Setup ........................................................................................... 13

5.1.4 Confirmation .........................................................................................................................14

6Communicate ............................................................................................................................. 15

Appendix: A Troubleshooting.................................................................................................. 16

A.1 System Status...................................................................................................................................... 16

A.2 Supplemental Configuration ......................................................................................................... 16

A.3 Configure ...............................................................................................................................................16

A.4 System Time......................................................................................................................................... 17

A.5 Update System.................................................................................................................................... 17

A.6 Battery Replacement........................................................................................................................ 17

A.7 Network Defaults Jumper .............................................................................................................. 18

A.8 Firewall ...................................................................................................................................................19

Appendix: B Regulatory ........................................................................................................... 20

Appendix: C Configuration Checklist - Static ..................................................................... 21

Appendix: D VertX Installation Worksheet..........................................................................22

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Page 4 of 25 July 2016

1Introduction

HID Global’s VertX EVO® open platform is flexible and scalable to permit economic and high

performance access control solutions for a wide range of applications. The VertX EVO V1000

interconnects through different sub-networks and protocols to a standard TCP/IP network with

the capability of a variety of applications.

For example, the VertX EVO Access Controllers are a cost-effective method for two-way

communication using Ethernet between a computer and a V1000. In addition, the VertX EVO

V1000 communicates through a RS-232 serial port and multi-drop RS-485 ports.

1.1 Parts List

Description

Quantity

VertX EVO units (one of the following):

V1000 (Access Controller)

Note: Each VertX EVO controller has a plastic base and is covered with a

plastic lid.

1 V1000 used with any

combination of (up to

32) interface panels.

•

Lithium Battery

•

Mounting screws

•

2.2K EOL resistors

8 ea. V1000

•

Quick Installation Guide

•

Installation Wiring Diagram Example 1

Note: One or more VertX Interface panels are required when installing a VertX EVO V1000

controller.

1.2 Product Specifications

Description

Specification

Power Supply 12-24VDC

Maximum Current at 12-24VDC per Unit 1 Amp

Average Operating Current at 12VDC 210mA

Operating Temperature Range

32°-120°F (0°- 49°C)

Humidity

5% to 85% non-condensing

SD Card Contact System/Software OEM to discuss possible

usage and SD Card specifications.

USB Port Reserved for Future Use

July 2016 Page 5 of 25

see

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

1.3 Cable Specifications

Cable Type

Length

Specification

RS-485 *

4000 feet (1220 m) to

host

Using Belden 3105A, 22AWG twisted pair, shielded 100

Ω

cable, or equivalent.

Input Circuits * 500 feet (150 m) 2-conductor, shielded, using ALPHA 1292C (22AWG) or

Alpha 2421C (18AWG), or equivalent.

Output Circuits * 500 feet (150 m)

2-conductor, using ALPHA 1172C (22AWG) or Alpha 1897C

(18AWG), or equivalent.

Wiegand

500 feet (150 m) to

reader

ALPHA 1299C, 22AWG, 9-conductor, stranded, overall

shield.

Fewer conductors needed if all control lines are not used.

Ethernet 328 feet (100 m) Cat5, Cat5E, and Cat6

Power Supply

12-24 VDC IN ---- Refer to your Power Supply Installation Guide.

* Minimum wire gauge depends on cable length and current requirements.

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Page 6 of 25 July 2016

2Overview

The following outlines what is required to install VertX EVO controllers.

July 2016 Page 7 of 25

see

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

3Connect

3.1 What you need before getting started

Prior to starting the installation, completely read this guide.

See Section Appendix C: Configuration Checklist - Static, and gather the information before

proceeding with these instructions.

CAUTION: VertX controllers and panels are sensitive to Electrostatic Discharges (ESD).

Observe precautions while handling the circuit board assembly by using proper grounding

straps and handling precautions at all times.

3.2 V1000

1. Verify the battery jumper is installed in the ON position, P10 connector.

2. If installing a V1000 - Verify the RS-485 termination jumper is in the Out position

when there are no panels attached to the port. If there are downstream interface

panels attached, place the termination jumper in the In position. The V1000 is

shipped with jumpers in the Out positions.

Note: P6 controls Port 2 and P5 controls Port 1. This is an issue if one of the jumpers

is in the IN position and the other is in the OUT position.

3.3 Mounting Instructions

1. Always mount the controllers and interface panels in a secure area.

2. Mount using the four mounting screws (provided) or other appropriate fasteners.

Place the fasteners in the corner holes of the base.

3. Stack the VertX EVO devices with or without the cover. Do not remove the plastic

base. Position the VertX EVO devices in such a way as to provide room for wiring, air-

flow and cable runs.

CAUTION: Stacking the VertX EVO devices without the cover in place risks the danger of

breaking the LEDS unless spacers are used for separation.

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Page 8 of 25 July 2016

3.4 Wiring VertX EVO

WARNING: VertX EVO V1000 is a NON-PoE device. DO NOT connect J1 (Ethernet port) to a

PoE capable port. This applies to both direct PoE Power Sourcing Equipment (Endspan

PSE) and PoE injector (Midspan PSE) equipment. Not all PSE's correctly detect Non-PoE-

capable devices, and such PSE's may not function as expected when connected to Non-PoE

equipment. If the only option is to connect the controller to a PoE enabled port, disable

power of the PoE port before connecting.

Note: Carefully peel the attached Warning Label from the bottom of the unit and leave the

label attached to the unit's cover for future reference.

CAUTION: Connectors on the VertX EVO devices are positioned to be mirror images and are

not interchangeable once the installation is complete. Therefore, you cannot unplug a

connector from one side and plug it into the corresponding connector on the other side.

1. Network Connection: Connect the VertX EVO V1000 to the network using

a standard Cat5 network patch cable. Connect one end of the Cat5 network patch

cable to the J1 (RJ-45) connector on the V1000 and the other end to the network

connection point (network jack, hub, switch, or router) on your site.

Note: Two LED lights exist on the RJ-45 connector. The green LED denotes Ethernet

Activity and the yellow LED denotes speed. When the Yellow LED is on, it indicates

100 Mbits per second. Another LED in-board is a Duplex LED, indicating duplex

communications are available.

2. Power and Alarm input connections (All VertX EVO units): Connect power by

providing appropriate DC input to the P7 connector. Appropriate DC input goes to

Pin 1 and ground to Pin 2. Batt Fail, AC Fail, and Tamper switch inputs are wired as

shown in the table. Connect the Bat Fail and AC Fail inputs to battery low/failure and

AC failure contacts provided on the power supply. Connect the Tamper input to a

tamper switch on the enclosure.

Pin #

12-24VDC

2 Ground

Bat Fail -

4 Bat Fail +

AC Fail -

6 AC Fail +

Tamper -

8 Tamper +

July 2016 Page 9 of 25

see

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

3. RS-485 Connections: The V1000 has two RS-485 connectors and uses the 10-pin

connector on P3 and P4. Each RS-485 bus can support a maximum of 16 V100-Series

panels using one or two ports.

Having two ports on each bus provides the option of splitting each RS-485 bus into

two physical connections, allowing a total of four physical connections for the two

busses.

RS-485 busses must be connected in a daisy chain topology and not a star topology.

The V1000 RS-485 termination jumper should be in the Out position if there are no

panels attached to the port. If there are downstream panels attached then the

termination jumper should be in the In position.

PCB Pin #

V2000 P1

PCB Pin #

V1000 P4 (port 3 and 4)

2 B 9 B

Shield

4 Not in use 7 Not in use

Not in use

6 A 5 A

8 Shield 3 Shield

9 Not in use 2 Not in use

10 Not in use 1 Not in use

CAUTION: The V1000 RS-485 Ports 1 & 2 (P3) are a common bus and therefore

cannot have panels with duplicate Interface Addresses assigned. The same is true

of the V1000 RS-485, Ports 3 & 4 (P4). For example, two panels, both with

Interface Address 0 (factory default), cannot be connected to Ports 1 and/or 2 (P3).

Wire the RS-485 to the In position only of the P9 terminal block for the V100-Series

panel. This is especially important when the RS-485 communication is in a “daisy

chain” configuration. If the RS-485 is wired In and Out, and power is lost, or the P9

terminal block is unplugged on a V100-Series panel, RS-485 communications will be

lost to downstream V100-Series panels.

VertX EVO V1000 User Guide, 71000-901, Rev. A.4

Page 10 of 25 July 2016

4. Output Connections (VertX EVO V1000): All Output connections are used for

general purpose controls. The following table shows where the various outputs are

located. Pin numbers shown use the convention “NO/C/NC”.

For example, Output 1, V1000: P14 Pin 3 is NO (Normally Open)

Pin 4 is C (Common) and Pin 5 is NC (Normally Closed).

Note: Relays are dry contact rated for 2Amps @ 30VDC.

Output Number

V1000

1 P14 Pins 3/4/5

P11 Pins 3/4/5

CAUTION: Some magnetic locks exhibit both high in-rush current when activated

and a high instantaneous break voltage when de-energized due to magnetic field

collapse. Use a snubber circuit across the controlling relay terminals to protect the

controlling relay contacts. Go to support.hidglobal.com, see Solution 891 - How do

I wire a High In-Rush Current locking device to VertX/Edge/Edge Solo?

5. Input Connections: Input connections are analog inputs used for a combination of

specific functions such as Request-to-Exit (REX), Door monitor, etc. They can also be

used as general purpose monitoring. Connect one side of the switch or contact to the

+ (plus) lead and the other to the – (minus) lead. The following table shows where the

inputs are located. Pin numbers shown on the cover use the convention +/–.

The default REX input configuration is normally open (NO) unsupervised (no EOL

resistors).

However, the default Door Switch (DS) configuration is Normally Closed (NC),

unsupervised (no EOL resistors).

All other input points are defaulted for NO switches and are unsupervised (no EOL

resistors).

Any input can be configured as NO or NC, as well as unsupervised or supervised.

Autres manuels pour VertX EVO V1000

Table des matières

Autres manuels HID Porte

HID

HID ENTRYPROX Manuel utilisateur

HID

HID R10-H Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur