Hi-Link HLK-RM08K Manuel utilisateur
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
SHENZHEN HI- LINK ELECTRONIC CO.,LTD
HLK-RM08K USER MANUAL
UART to Ethernet Application
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
Note : The complete starter kit includes following items.
HLK-RM08K module
HLK-RM08K development board
2.4G 2DB antenna
5V 1000mA power adapters
Network cable (If needed)
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
1. Brief introduction
HLK-RM08K is a new low-cost embedded UART-ETH-WIFI module (serial port - Ethernet -
Wireless network) developed by Shenzhen Hi-Link (HK) co., Ltd.
The product is a low power consumption WIFI module,supports EEE802.11b/g/n wireless
protocol with small size and smart use,ully transparent transmission UART module, built-in TCP /
IP protocol stack, enabling users short development cycle. It just needs host computer,WEB
browser or APP to set up parameters, making the connection between UART and network.
HLK-RM08K has stable performance and flexible use, meeting kinds of requirements of users. and
strong technical supports could be provided. Also, it could be customized,such as WEB
interface ,mobile phone app and so on.
一. UART to Ethernet configuration method
Method 1：Via UART to configure
1. Restore factory setting. Power on 5V/350MA, and wait for 20s. Pull down ES1 pin more then
6S after setting up. The system will restart automatically. Then the system is on the factory mode.
2. Power on module and wait for 10s until the LED is flashing.Make the connection of two uart
ports of DB9 and PC.Or use USB-UART cable connect the HLK-RM08K development board.
Picture for reference ：
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
3. Short press ESO button, start the configuration tool,choose the uart number then click search
module. It will return at (:Found Device at COM7(115200)! in the text box.Click inquiry
configuration to read the current parameters.
4. Configuration parameters
Working mode selection: : UART to Ethernet
Network protocol select: TCP server
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
Network IP : Remote IP does not work as server
Port :TCP server set monitoring port.
UART parameter: Change it as required
Parameters configurations are as follows,
Disable DHCP, configure it as static IP.
Apply the configuration, WIFI and LAN are closed.
Note : At this mode, local IP and WAN IP must be different network segment.Or could not
access internet.
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
5. Data transmission between TCP and Serial port.
Apply all the parameters, the module will reset. Or power on module again,connecting the net
ports of PC and RM08K. Chose all the network cards, configure HLK-RM08K as follows,
ping 192.168.16.254 :Start ----Run ----cmd
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
Set up serial configure tool and network testing tool, testing the data if could be sent.
Then the serial port and ethernet could send data each other.
6. The configuration method of serial 1 is same as serial 0.
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
Method 2 Via network port configuration
1. Restore factory setting and set up the module, use the network cable to connect LAN 2 and
PC. Configure PC as follows.
ping 192.168.16.254 :Start----Run ---Cmd
Shenzhen Hi-Link Electronic Co.,Ltd
Http://www.hlktech.com Tel:0755-83575155 Fax:0755-83575189
Shenzhen Hi-Link Electronic Co.,Ltd
2. Enter the site http://192.168.16.254, enter the user name and password admin, then transfer
to the configuration page.
Configure IP and DHCP, Click apply to wait for the module restarting.
3. Once the module restart,change the net cable from LAN2 to LAN 1 then refer to the manual
from step 5 of method 1.
Autres manuels pour HLK-RM08K
2
Autres manuels Hi-Link Unité de contrôle
Hi-Link
Hi-Link HLK-LD2410 Manuel utilisateur
Hi-Link
Hi-Link HLK-LD2420 Manuel utilisateur
Hi-Link
Hi-Link HLK-RM08S Manuel utilisateur
Hi-Link
Hi-Link HLK-7688A Manuel utilisateur
Hi-Link
Hi-Link HLK-LD015-5G Manuel utilisateur
Hi-Link
Hi-Link HLK-B20 Manuel utilisateur
Hi-Link
Hi-Link HLK-7628N Manuel utilisateur
Hi-Link
Hi-Link HLK-LD2410 Manuel utilisateur
Hi-Link
Hi-Link HLK-B10 Manuel utilisateur
Hi-Link
Hi-Link HLK-7628D Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
