Herutu WCL-426R Manuel utilisateur

LAN Connection TypeAndon Receiver

WCL-426R

INSTRUCTION MANUAL V1.30

Please use this operation manual correctly on reading well.

Please keep it carefully to be able to read immediately, when required.

 
 
Table of Contents 
 
1．Overview..................................................................................................................................... 1 
1-1．Introduction ......................................................................................................................... 1 
1-2．Main Unit and Accessories ................................................................................................ 1 
1-3．Safety Precautions (Be Sure to Read This)...................................................................... 2 
1-4．Outline.................................................................................................................................. 4 
2．Specification............................................................................................................................... 5 
2-1．Radio Part Specification..................................................................................................... 5 
2-2．General Specification ......................................................................................................... 5 
3．Part Names and Descriptions................................................................................................... 6 
4．Drawing....................................................................................................................................... 7 
5．Prepare to Start Communication.............................................................................................. 8 
5-1．Installation of "Device Installer"........................................................................................ 8 
5-2．Factory Default IP Address................................................................................................ 8 
5-3．IP Address Settings and Procedure.................................................................................. 8 
6．Settings..................................................................................................................................... 15 
7. Communication Command Function..................................................................................... 17 
7-1．Information Acquisition Command................................................................................. 17 
7-2．Setting Command ............................................................................................................. 17 
7-3．Command Execution Result............................................................................................ 17 
8．Installation Procedure............................................................................................................. 21 
8-1．Receiver Installation......................................................................................................... 21 
8-2．LAN connector .................................................................................................................. 22 
9．Description of Operation......................................................................................................... 23 
9-1．Basic Operation................................................................................................................. 23 
9-1-1．Opening....................................................................................................................... 23 
9-1-2．Receive Data from Transmitter................................................................................. 23 
9-2．LED Monitor....................................................................................................................... 24 
9-3．Processing at Power ON.................................................................................................. 26 
10. After Service and Warranty ................................................................................................... 27 

1．Overview

1-1．Introduction

This instruction manual describes the information required for using this product including overview,

installation, and operation of this product. Read this manual carefully before using this product. Keep this

manual handy so that you can take it out immediately.

▪Do not use this product for the application that may cause harm to human body or damage to other

devices and equipment.

Do not use this product near the devices that may malfunction due to radio waves emitted from this

product.

▪Because the communication performance is changed depending on the surrounding environment, be

sure to confirm the communication is established before installation of this product and then use it.

1-2．Main Unit and Accessories

■Receiver

Receiver main unit “WCL-426R”×1

AC adapter “ADB24050” x1

Cable Approx. 1.5 m

Antenna “TK-1842”×1

1-3．Safety Precautions (Be Sure to Read This)

This section describes the matters to be observed in order to prevent harm to the users and other persons

and damages to the property.

■The following marks and displays classify and describe the extent of harm and damage caused by failing

to observe the display content and using this product wrongly.

This display column shows "a failure to do observe it could result in death or

serious personal injury".

This display column shows "a failure to do observe it could result in only the

personal injury or property damage".

■Common matters in handling

●Avoid using this product in the humid or dusty place. Dusts or water enters the product,

which may cause the fault, fire, or electric shock.

■Handling this product

●This product is the wireless communication equipment made of precision parts. Do not

disassemble or modify it. Or the accident or fault may occur.

■Handling this product

●Do not use this product for application that requires the extremely high reliability affecting

the human life.

●Do not use this product in the area which the radio wave reaches or not.

■Handling the power supply

Be sure to observe the followings in order to prevent the accidents such as heat generation, damage, or

ignition ofAC adapter and power cord.

●Do not place the AC adapter and power cord close to fire or insert them into fire. Or they

may be burst and ignited, resulting in the accident.

●Use the AC adapter and main body only at the specified power supply voltage in order to

prevent burst and ignition accidents.

! Warning

! Caution

! Warning

●Do not use the AC adapter and main body at the location where they easily get wet. Or the

accidents including heat generation, ignition, or electric shock and faults may occur.

●Do not touch the AC adapter, main body, power cord, and outlet with wet hands. Or the

accident such as an electric shock may occur.

●Do not damage the power cord. Short-circuit or heat generation may cause fire or electric

shock.

●Do not use the power plug with dusts attached. Short-circuit or heat generation may cause

fire or electric shock.

●Do not give a strong shock to theAC adapter.

Or the accident or fault may occur.

●If you find a deformation in theAC adapter, do not use it.

Or the accident or fault may occur.

●Do not charge the main body at the location where the flammable gas is generated.

Or the ignition accident may occur.

●Never disassemble the AC adapter.

Or the accident or fault may occur.

■Never disassemble the AC adapter.

Remove the power plug from the outlet because it may cause fire and electric shock. Request the dealer

or our company to repair it.

●When smoke comes or there is a strange smell, immediately stop usage and remove the

power plug from the outlet because it may cause fire and electric shock. Request the dealer

or our company to repair it.

●If the cord is damaged, do not use it. Using the cord damaged continuously may cause fire

or electric shock.

■Reliability of wireless communication

As wireless communication has properties that are different from those of wired communication,

communication errors may occur due to the following.

・Exceeds the communication distance.

・Enters a dead zone.

・Interfered by strong jamming

If signals are often jammed, or being jammed leads to operational problems, stop using the systems and

restart using the systems after removal of the cause.

Radio waves may not be received due to various reasons other than the above. Please understand this

before using the systems.

* A dead zone is an area where the radio wave transmitted from the transmitter becomes extremely weak

due to radio waves reflected from walls or other objects.

1-4．Outline

WCL-426R is a LAN connection typeAndon*1 receiver (hereinafter called “receiver”).

The receiver can wirelessly receive in real-time trouble occurrence reports transmitted from theAN426TⅡ

transmitter installed at the workstations and machines of the production line.

In addition, the receiver can externally output the received reports of trouble occurrence via LAN.

By utilizing and analyzing the information of trouble occurrences on the production line with applications on

computers, tablets and in the cloud, the receiver can be useful for visualizing and improving the operation

status of the production line.

Using the Windows application “Production Process Support Software for WCL Series WCL plus,” you can

save the trouble occurrence history received by up to 10Andon receivers in the CSV format.

1. At the transmitter, there are two selectable input methods for reporting trouble occurrences: one for

workers with four push-buttons (orange, red, green, and white) and one for machines with four external

inputs (orange, red, green, and white).According to possible trouble occurrences in the production line,

you can assign each color a meaning, such as red for an exception occurrence, orange for parts out of

stock, green for requesting transportation of finished products, or white for trouble solved.

2. When using the receiver linked to a wireless Andon seriesAN426Ⅱ, one receiver can wirelessly

communicate with up to 800 transmitters and a maximum of 10 receivers can be used in a factory. This

enables trouble occurrence reports to be collected from up to 8,000 locations in a factory.

When using the receiver with the transmitter without linking to a wirelessAndon seriesAN426Ⅱ, each

receiver can wirelessly communicate with up to 1,000 transmitters and a maximum of 10 receivers can

be used within a factory. This enables trouble occurrence reports to be collected from up to 10,000

locations in a factory.

*1:A system to notify management, maintenance, and other workers of a quality or process problem.

2．Specification

2-1．Radio Part Specification

Item

Specification

Frequency Band

426.0250MHz～426.1375MHz

Modulation Band

Direct 2-value FSK modulation

Modulation Speed

Approx.977bps

Channel Step

12.5kHz(Step 10Wave)

Antenna

External Whip Antenna

Communication

Method

Receive only

2-2．General Specification

Item

Specification

Interface

Ethernet IEEEE802.3 10Base-T/100Base-TX Auto switching

Connector: RJ-45 ×1

Indication for network 2-color LED ×2

Display

Red LED × 1 (Power supply monitor)

Red/Green 2-color LED × 1 (Monitor for wireless communication)

Red/Green 2-color LED × 1 (Monitor for wired communication)

Power Source

DC24V (Available at AC100-240V with supplied AC adapter.)

Current Consumption

Approx. 120mA

Operating

Environment

Temperature:0-+40℃(32-104°F)

Humidity:35-80% (without condensation)

External Dimensions

(W × H × D) 135 × 90 × 35mm (5.3 × 3.5 × 1.4″) (excluding protrusions)

Weight

Approx. 380g (13.4 oz)

Switches

2P DIP switch × 1 (For normal operation settings)

16P rotary switch × 1 (For channel settings)

Accessory

1 AC adapter, 1 Antenna

Setting switch

Connector for antenna

LED monitor

LAN Connector

DC jack

Mounting hole

3．Part Names and Descriptions

Name

Function

Connector for

antenna

Connector for connection to the antenna. (BNC-J Connector)

Attach the supplied antenna.

Mounting holes

Mounting hole of φ4.5 × 4

DC jack

DC jack for connection of the included AC adapter.

Setting switch

DIP switch and rotary switch for settings.

LED monitor

LEDs for power supply, wireless communication and wired communication.

LANConnector

Connector for LAN connection. (RJ-45)

4-φ4.5取付穴

125

115

135

10 10

(41)

(160)

4．Drawing

4-φ4.5 Mounting hole

Table des matières

Autres manuels Herutu Récepteur

Herutu

Herutu TW-800R-EXS Manuel utilisateur

Herutu

Herutu TW-800R-SLNX Manuel utilisateur

Herutu

Herutu TW-800R-MCL Manuel utilisateur

Herutu

Herutu TW-800R-SC Manuel utilisateur

Herutu

Herutu WCL-920R Manuel utilisateur

Herutu

Herutu TW-800R-EXL Manuel utilisateur

Herutu

Herutu POKAYOKE TWF-600R Manuel utilisateur

Herutu

Herutu TW-510R Manuel utilisateur

Herutu

Herutu TW-800R-EXP Manuel utilisateur

Herutu

Herutu AN426RM II Manuel utilisateur

Herutu

Herutu TW-800 Series Manuel utilisateur

Herutu

Herutu TW-800R-EXS Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur