Herman Miller Ode Guide de l'administrateur
Herman Miller Ode Lamp Assembly Instructions2Part # 1BGH00 Rev. C
Feed wire end through lamp head assembly.
Step 2
Remove rubber band from column to free wire end from top of column.
Step 1
Power Driver Phillips Screw Driver /” Allen Wrench/” Allen Driver Bit Phillips Driver Bit
Parts Included
Tools Required
How to assemble your floor lamp.
A. Shade Weldment C. Column Assembly
Top
BottomB. Lamp Head Assembly Base Assembly
D. Head Hardware
) Flat Head Screws ) M6 Lock Nut
& Set Screws
Mounting Plate Insulator
Power Supply
E. Hardware
HermanMiller
Ode Floor Lamp
™
F. Shade Support Hardware
OR
Herman Miller Ode Lamp Assembly Instructions3Part # 1BGH00 Rev. C
Set lamp head assembly into place on top of the column.
Step 3
Install three pan head machine screws around the shade support. The ring
terminal on the wire must be installed on one of these machine screws with
internal tooth lock washer before it is installed the screw with ring terminal
must be securly tightend to ensure conductivity to the post.
Step 4
Step 5 Step 6
Plug the wire connector into the side of PCB driver board.
The screw with ring terminal must
be securly tightend to ensure touch
sense conductivity.
Screw the shade mounting plate into the lamp head assembly using four flat
head screws. Make sure that the wire is underneath of this plate.
Attachringterminalwith
screw here.Tightensecurely.
Example:
Herman Miller Ode Lamp Assembly Instructions4Part # 1BGH00 Rev. C
Twist the shade weldment onto the mounting plate.
Step 7
Feed wire through central hole of base assembly.
Studs/set screw
Step 8
Step 9 Step 10
Attach base assembly using three Allen head screws. Make sure that the
insulator is installed between the base assembly and the screws.
Connect power supply cord to floor lamp.
Herman Miller Ode Lamp Assembly Instructions5Part # 1BGH00 Rev. C
Place lamp on desired floor location, making sure power supply and cord are
properly routed. Plug power supply into a standard electrical outlet.
Step 11
For more information about our products and services please visit us at
hermanmiller.com or call () .
© Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. BGH
® Yand Herman Miller are among the registered trademarks of Herman Miller, Inc.
™ Ode is among the trademarks of Herman Miller, Inc.
To operate lamps:
Grasp any part of the stem to
turn lamps on or o.
NOTE: By design light automatically shuts
o aer nine hours.
For Example: The light is turned on and runs for
two hours before being turned o. The light is then
turned on again so now it will continue to run for
an additional seven hours and then will turn o
automatically.
Note: Aer connecting power to
the unit, there will be a second
delay before the lamp can be
turned on via touch sense.
Table des matières
Autres manuels Herman Miller Éclairage extérieur
Manuels Éclairage extérieur populaires d'autres marques
Lindby
Lindby 9949029 Manuel utilisateur
HEPER
HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation
HEPER
HEPER LW8034.003-US Instructions d'installation et d'utilisation
Maretti
Maretti VIBE S 14.6080.04.A Manuel utilisateur
BEGA
BEGA 84 253 Manuel
HEPER
HEPER MINIMO Instructions d'installation et d'utilisation
LIGMAN
LIGMAN BAMBOO 3 Manuel utilisateur
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur
urban ambiance
urban ambiance UQL1273 Manuel utilisateur
TotalPond
TotalPond 52238 Manuel utilisateur
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuel utilisateur