Heatmiser Multi-Link Manuel utilisateur
Mul-Link
Setup Guide
Revision 1.0
Contents
1
What is Mul-Link? 2
Seng up the Mul-Link (Steps 1-3) 3 - 4
Security Types Explained 4 - 5
Seng up the Mul-Link (Steps 4-7) 6 - 9
Adding WiFi thermostats to the Mul-Link 9
Checking WiFi Connecon 9
App Connecon 10
Remote Access 11
Troubleshoong 12
What is Mul-Link?
The Mul-Link allows you to control mulple
Heatmiser WiFi thermostats via free smartphone
applicaon.
Up to 32 thermostats in total can be controlled.
The Mul-Link acts as a gateway to your WiFi
Network by taking care of the thermostat port
forwarding, this drascally simplies the setup
procedure.
2
Step 1
Download and install the network ulity for the
Mul-Link from our web site.
www.heatmiser.co.uk/wi
Step 2
Connect the Mul-Link to your pc with the USB
cable provided, this will power the device from the
USB port & will allow you to test the Wi-Fi
connecon.
On the Ulity press Read to view the current
Mul-Link conguraon.
Seng up the Mul-Link
3
Step 3
Enter the SSID, Security Type and Security Code of your wireless network.
These sengs can be found in your wireless router, consult your router manual for more
informaon.
Security Types explained
There are currently 4 methods of securing your wireless connecon in common use
These are :
OPEN/DISABLED (not recommended)
W.E.P. (lowest security level)
W.P.A. (medium security)
W.P.A.2. (highest security)
Your choice of security sengs in the Mul-Link must match the seng in your router.
Quite oen you will nd WPA and WPA2 as a single opon in the router, this is perfectly normal
the router knows which one to use, and you can therefore set the Mul-Link up using either one.
4
...Security Types Connued
The password can be up to 63 characters in length including spaces _. / \ characters.
The W.E.P. opon is not as simple, some routers generate a hidden password from a pass phrase
whilst others require a 10 or 26 digit hex password and won’t accept anything else.
Your Mul-Link ulity can deal with both opons.
The following restricons apply:
A hex password can only be made up of the numbers 0 to 9 and the leers a to f, lower case only.
Hex passwords can only be 10 characters or 26 characters in length.
If a passphrase is used it must be either 5 or 13 characters in length but can be any leer or
number.
Your Mul-Link will automacally calculate the same hidden password your router creates from
the same phrase.
You will nd most routers have these same restricons.
5
Step 4
It is likely that your network will be congured to operate on a DHCP basis – this means your
router automacally issues an IP address to a device that successfully connects to the network.
Your Mul-Link needs a xed IP address in order for local and remote access to operate,
The xed IP address needs to be outside of the router DHCP range, so you will need to set this up
manually.
Log into your wireless router and navigate to the LAN sengs page. You should see an
opon for DHCP setup. This should detail the IP range that can be assigned to devices
connecng to the network.
As an example, you may have an IP starng range 192.168.1.1 and ending 192.168.1.99
This would mean you can safely provide your Mul-Link the IP address 192.168.1.100 as no other
devices will be assigned this address by the router.
6
If your DHCP range is from 192.168.1.1 to 192.168.1.253 you cannot use 254 or above, you will
need to change the DHCP to a lower range, take care not to change any of the rst 3 sets of num-
bers.
Tip! When seng up an IP address, the rst three sets of numbers must be the same as the
router IP, the fourth set must not be used elsewhere on the network.
Step 5
Enter the Subnet mask for the network, this informaon can be found in your wireless router.
Step 6
You need to enter the IP address of your gateway and DNS.
In most cases, this is the IP address of your wireless router.
7
Step 7
App Pin Access
The access PIN is required when you are using the mul-
zone app and helps secure your system. This PIN number
should be the same number that has been used for the
WiFi Thermostats on the system.
Step 8
Adding WiFi thermostats to the Multi-Link
Click the Add buon, now enter the room tle and the
last three digits of the WiFi thermostat IP address, then
press OK.
This zone will then appear in the window at the boom
of the ulity.
Repeat this process for all of the WiFi thermostats on the
system.
You have the opon to select any of the zones in this
window and Edit or Delete if necessary. 8
Step 9
Checking WiFi Connection
Once you have entered the details of your WiFi network
& added the zones to the system press Apply.
“Update successful” will appear at the boom on the
ulity.
Disconnect the USB cable from the Mul-Link, wait 5
seconds then reconnect it.
Once the Mul-Link has rebooted wait approximately
one minute, the Wi-Fi LED on the Mul-Link will light up
indicang that the Mul-Link has successfully connected
to your WiFi network.
9
Table des matières
Autres manuels Heatmiser Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
