Heat Seal SM-1 Mode d’emploi

Revised 2017

READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING EQUIPMENT

OPERATING & SERVICE PARTS MANUAL

SCALEMATE OVERWRAPPER

Model SM-1

Model SM-1 with 12 Hour Timer,

Right and Left wings, Printer

Shelf and PS20 Label Dispenser

Model SM-1 with Left Wing,

Right Wing with Hood, and

All purpose Shelf.

Revised 2017

Operating Instructions ..................................................................................................3

Film Threading & Mounting ..........................................................................................4

Recommended Maintenance ........................................................................................5

Scalemate Schematic & Parts List ...............................................................................6

Troubleshooting Guide .................................................................................................7

Electrical Service Information ......................................................................................8

Hot Plate Schematic & Parts List .................................................................................9

Electrical Schematics & Replacement Instructions..................................................10

Replacing the Fuse & Circuit Board......................................................................10

Replacing the Hot Rod ........................................................................................... 11

Replacing the Hot Plate Heating Element.............................................................12

TABLE OF CONTENTS

Revised 2017

OPERATION

First, mount and plug in any accessories you plan on using with your Scalemate. The accessory outlet is located midway up on

the left side of the frame.

Next, plug your Scalemate wrapper into the appropriate power supply. The standard Scalemate wrapper utilizes a 115 volt AC

power supply.

To turn on your Scalemate, flip the toggle switch on the left side of the wrapper to the “ON” position. The red indicator light will

power on and remain on as long as the switch remains in the “ON” position.

Note: If your Scalemate has the factory option timer, see the instructions below for turning your machine on.

With the unit switched on, the hot plate and hot rod will begin to heat up to their set point temperatures. Once switched on, the

unit should become operational in five-seven minutes.

USING THE FACTORY OPTION TIMER

As a factory option, Scalemates can be ordered with a timer in lieu of the on/

off toggle switch. Once set, the timer will begin to power the hot plate and hot

rod until time runs out. To operate the timer, the dial must be turned past two

hours in order for the unit to begin heating. When finished, the timer can be

manually turned back to the off position.

OPERATING INSTRUCTIONS

Revised 2017

FILM THREADING & MOUNTING

THREADING THE FILM

Thread the film as shown, one at a time or as needed.

FILM SELECTOR

Pull different sized films into film selector and drape un-

used film in front of roller.

MODEL SM-1

MOUNTING FILM ON AXLE

1. Loosen four wing nuts (A)

2. Swing out upper bearing blocks (B) on both sides

3. Lift out axle assembly (C) and unscrew movable

end cap (D), position fixed end cap (E) for correct

film width then secure with pin (F) and o-ring (G)

4. Position the cardboard core of the film roll against

the taper of the fixed end cap. Make sure the film is

threaded from the bottom of the roll and under film

roller (H) (see threading diagrams)

5. Replace adjustable end cap (D) and screw on tight-

6. Replace the axle assembly (C) and film roll onto

the lower bearing blocks (J), swing upper bearing

blocks (B) back into place and tighten and adjust

wing nuts (A) for desired film tension

ITEM PART # DESCRIPTION

1 6305-018

Bearing Block Set, Includes:

Upper Bearing Block, RH

Upper Bearing Block, LH

Lower Bearing Blocks

2 6110-023

3” Core Adapter Set Includes:

3” Adjustable Core

3” Fixed Core

3 3005-004 Core Axle, 21 15/16” L

Revised 2017

RECOMMENDED MAINTENANCE

 MAKE SURE TO TURN OFF THE UNIT, PULL THE PLUG

AND LET THE MACHINE COOL DOWN BEFORE CLEANING *

NON-STICK COVER & HOT PLATE

 It is recommended to replace the Non-stick cover at least once every three months to protect the heating foil and maintain a

sanitary surface. The Non-stick cover is used to create a sanitary, stick free surface to seal film with the hot plate. Non-stick

covers are porous, meaning liquids or moisture can permeate the cover, get to the surface of the hot plate, and burn off on

the hot plate.

 It’s recommended that the Non-stick cover be replace every three (3) months or as needed depending on the level of daily

wear and tear. The Non-stick cover should be changed if the surface is soiled, or holes, punctures, excessive wear, or dam-

age are present.

 The hot plate can be cleaned, as needed, with a mild spray degreaser, applied to a soft rag or paper towel and then wiped

on the plate while cold.

CUT OFF ROD

 Make sure that the unit is turned off and the cut off rod is cold to the touch.

 The film cut off rod can be cleaned, as needed. Cover the unit surfaces with paper towels to protect them from over spray

and debris.

 Spray and coat the Cut-off Rod generously with an FDA approved “Degreaser” product.

 After soaking for a few minutes, lightly scrub the surface of the Cut-off rod with a Scour Pad (Scotch-Brite™ type pad).

 Wipe the surface clean of debris and residue with clean paper towels or cloths.

CLEANING THE UNIT

 The machine can be completely wiped down using mild cleaning detergent and soft rags or paper towels. Do not hose down

or submerse the unit.

Revised 2017

SCALEMATE REPLACEMENT PARTS

ITEM QTY PART # DESCRIPTION

1 4 1903077 SCR, MACH, PAN HD, SLOT, SS, 8-32 X 3/8 LG.

2 1 1905021 SCR, SET, SOCKET, CUP PT, 8-32 X 1/4, BLACK

3 4 1905055 Screw, Self Tap, Type 23 8-32 x 1/2

4 5 2105009 BEARING, FLANGE, NYLON, 5/16 ID. X 1/2 OD. X 1/2 LG.

5 6 2105057 BEARING, FLANGED, BRONZE,

6 1 2150011 Decal, Film Tension Tightness

7 1 2150143 LABEL, THREADING DIAGRAM

8 6 2185002 O RING, 5/8 ID X 13/16 OD

9 1 3005010 Collar, Cutoff Rod, 3/4 OD x .390 ID, 1/4 THK, 8-32 Tap

10 1 6401020 FLIPPER, FILM SELECTOR

11 6 6401021 SHAFT, FILM SELECTOR/FILM

12 1 6401025 SEPARATOR, FILM - SCALEMATE

13 1 6401027 ROD, SEPERATOR, FILM

14 1 6401062 HOUSING, MOUNTING, SCALE

15 5 6401070 TUBE. FILM GUIDE - 20"

16 1 6401087 Bracket, Tension Roller - Right

17 1 6401088 Bracket, Tension Roller - Left

18 1 6401089 Cover, Bracket - Tension Roller, Right

19 1 6401090 Cover, Bracket - Tension Roller, Left

20 1 6401111 TUBE, FILM GUIDE - 5/8 X 19 3/8

21 1 1824018 Hot Rod Heater

Revised 2017

TROUBLESHOOTING OVERWRAPPERS

GENERAL QUESTIONS

If new machine doesn't turn on (heat up) what

should we do?

Ensure power switch is ON. Check if fuse is blown. Check for loose wires in

the electrical box, shipping may loosen wire connections.

My unit is tripping the GFCI? The wires in the hot plate may be shorting and should be insulated with a high

temperature electrical tape. If the thermostat is shorting to ground, replace the

thermostat.

What is the standard voltage on wrapping ma-

chines?

110V - (220V is available)

Does the Heating Element 6110-016 fit all hot

plates?

The element fits the 6 by 15, 8 by 15 and 9 by 12 hot plates.

The 6 by 9 hot plate uses 6504-022 element.

My timer will not set for short amounts of time? You must turn knob on the timer past 2 and set back to desired time.

How do I change my Non-stick cover? When unit is cool, pull cover off it is not attached.

Where can I get transformers? They are no longer available. You need a hot rod conversion kit.

What kind of film do I use? PVC stretch film for wrapping meat and produce, its chemical characteristics

provide barriers to protect the product. Stretch film for pallet wrap is Polyeth-

ylene and not to be used on wrappers.

ABOUT HOT ROD

My hot rod is cold, what should I do? a) Check the fuse, replace if blown.

b) Check the circuit board for loose wires.

c) See page 2 for testing the Hot Rod Circuit Board.

My hot rod is not hot enough or too hot, what

should I do?

a) Check the circuit board, if potentiometer has been adjusted the rod will no

longer work correctly.

b) See page 2 for testing the Hot Rod Circuit Board.

My hot plate works but my hot rod doesn't? a) Hot Rod, Circuit Board and Fuse Holder work together.

b) Hot Plate, Thermostat and Element work together.

c) Hot Plate and Hot Rod are independent of each other.

ABOUT HOT PLATE

Why is the Hot Plate smoking? That is excess protective coating on the heating element burning off and

should last no more than 10 or 15 minutes.

My hot plate is cold? Check element then thermostat and wires to thermostat.

**WHEN REPLACING THE HOT ROD OR CIRCUIT BOARD,

IT IS RECOMMENDED TO REPLACE BOTH SINCE THEY WORK TOGETHER.**

Revised 2017

ELECTRICAL SERVICE INFORMATION

HOT ROD CIRCUIT BOARD TEST

A standard 115 volt neon circuit tester can be used for these tests.

CHECKING FUSES

Remove the fuse from their housing units located on the front of the electrical box. If a visual inspection does not verify a blown

fuse check for continuity by using the meter to read across the two terminals of the fuse.

If the meter reading does not show continuity, replace the fuse.

CHECKING THE HOT ROD

With the power turned OFF, remove the red hot rod wires from Terminals 1 and 2. Using the meter, measure the resistance of

the rod by connecting the leads of the meter to the red wires.

The meter should read between 130-136 ohms. If the reading is out of this range, replace the hot rod.

CHECKING THE CIRCUIT BOARD

After the hot rod and both the fuses have passed the above testing procedures, the circuit board can be tested.

With all the wires shown in the example circuit board (above) properly connected and the power ON, use the meter to test the

voltage across Terminals 1 and 2. If there is no voltage being read, the board needs to be replaced.

ELECTRICAL REQUIREMENTS

All Models are 110 Volts, 10 Amps.

THIS UNIT SHOULD NOT BE OPERATED IF ROD TEMPERATURE EXCEEDS

300 DEGREES FAHRENHEIT. IF SMOKE OR FUMES ARE DETECTED, DISCONTINUE USE

Revised 2017

ELECTRICAL SCHEMATICS & PARTS

ACCESSING ELECTRICAL COMPONENTS

The electrical components are located in the electrical

enclosure below the hot plate. To access the compo-

nents, unscrew the six screws (A) on the bottom of the

electrical enclosure. With the screws removed the bottom

panel (B) slides out to the left as shown.

WARNING: MAKE SURE THE MACHINE IS UNPLUGGED

AND HEATING ELEMENTS ARE COOL BEFORE SERVICING.

ITEM PART # DESCRIPTION

1 5901011 Non-stick Cover 6x15

5901001 Non-stick Cover 8x15

2 6101020 Hot Plate Assy. 6x15, 115V STD

6102043 Hot Plate Assy. 8x15, 115V STD

6305076 6x15 Fabricated Hot Plate

3 6305079 8x15 Fabricated Hot Plate

4 6401067 Electrical Housing

5 1905018 Screw, Self Drill 8-32 5/8" Pan, Phil

6 6110016 Element

7 6305080 Element Support Plate

8 1881002 B-200 Thermostat

9 2145023 Knob

HOT PLATE ASSEMBLY AND NON-STICK COVER

To replace a worn or torn non-stick cover, turn the machine off and let the hot plate and hot rod cool down. Once the hot plate

and non-stick cover are cool, simply lift off the cover (it is not attached) and replace with a new one.

Revised 2017

ELECTRICAL DIAGRAM & CIRCUIT BOARD

FOR MODEL SM-1

REPLACING THE FUSE

1. To replace the fuse, locate the fuse

holder on the back left portion of the

electrical enclosure next to the pow-

er cord.

2. Push in slightly and twist counter-

clockwise until holder and fuse pop

out.

3. Pull the fuse from the holder and

insert a new fuse.

4. Insert the fuse holder and new fuse

back into the mating portion on the

electrical enclosure. Push in and

twist clockwise to secure.

REPLACING THE CIRCUIT BOARD

 To replace the circuit board, unplug the machine and let the hot rod

and hot plate cool down.

 Once the hot rod and hot plate are cool, remove the access panel

on the bottom of the electrical enclosure (See “Accessing Electrical

Components”).

 With the panel removed, locate the circuit board and remove the

wires at connection one, two, three, four, five, and six as pictured

below. Mark each wire to remember what terminal it belongs on.

Failure to reconnect the wires to the proper terminals can cause

permanent damage to you machine.

 Next, locate the four plastic pins (A,B,C,D) supporting the circuit

board. Push in the tabs on the top of the plastic pins and pull the

board off the posts.

 Place the new circuit board over the four plastic standoffs and push

down until the board snaps into place.

 Reconnect the wires to the same terminals as on the old board.

Verify you have connected the wire to the proper terminals by

checking the pictures to the right.

 Replace the bottom shielding on the electrical enclosure and screw

tight.

6110-016

1821-034

Table des matières

Autres manuels Heat Seal Système d'emballage étirable

Heat Seal

Heat Seal 200ES Mode d’emploi

Heat Seal

Heat Seal 107ES Mode d’emploi

Heat Seal

Heat Seal SM20ES Mode d’emploi

Heat Seal

Heat Seal 112B Mode d’emploi

Heat Seal

Heat Seal D Series Mode d’emploi

Heat Seal

Heat Seal 700ES Mode d’emploi

Heat Seal

Heat Seal 700ES Mode d’emploi

Manuels Système d'emballage étirable populaires d'autres marques

U-Line

U-Line H-7208 Manuel utilisateur

M. J. MAILLIS GROUP

M. J. MAILLIS GROUP SIAT BeeWrap Manuel utilisateur

Omni

Omni Base Manuel utilisateur

U-Line

U-Line H-2304 Manuel utilisateur

U-Line

U-Line H-3701 Manuel utilisateur

Fromm

Fromm FR330 Manuel utilisateur

Orion

Orion H66-20 Manuel utilisateur

Omni Group

Omni Group Superplus Manuel utilisateur

Anderson

Anderson NutriWrap 780 SB Manuel utilisateur

Fromm

Fromm FR3 Series Manuel utilisateur

Orion

Orion H66-17 Manuel utilisateur

Orion

Orion FLEX RTA Manuel utilisateur

Tanco

Tanco 1510 Manuel de service

Rapid Packaging

Rapid Packaging Eagle 2000A Series Manuel utilisateur

Orion

Orion FLEX Series Manuel utilisateur

Fromm

Fromm FS 510 Manuel de service

Dibipack

Dibipack BABYPACK 1217 Manuel utilisateur

Fromm

Fromm FS35 Series Manuel utilisateur