Hanna Instruments TDS 1 Manuel utilisateur

SPECIFICATIONS

Range 0 to 999 ppm (mg/L)

Resolution 1 ppm

Accuracy (@20°C/68°F) ±2% f.s.

Typical EMC Deviation ±1% f.s.

Calibration

Manual, 1 point, through trimmer

Calibration Solution

HI70080 (800 ppm @25ºC)

Temperature Compensation

Automatic, 5 to 50ºC (41 to 122ºF)

Environment

0 to 50ºC (32 to 122ºF); 95% RH

Battery Type 4 x 1.5V alkaline

Battaery Life approx.150 hours

Dimensions 150 x 30 x 21 mm

(5.9 x 1.2 x 0.8")

Weight 70 g (2.5 oz.)

ACCESSORIES

HI 70080P 800 ppm calibration solution,

20 mL sachet, 25 pcs

HI 731326 Calibration screwdriver (20 pcs)

ISTTDS1R4 05/05

www.hannainst.com

TDS1

TDS Meter

with

Automatic

Temperature

Compensation

TDS1

TDS Meter

with

Automatic

Temperature

Compensation

OPERATIONAL GUIDE

• Remove the protective cap

and turn the tester on by

sliding the top switch.

• Immerse the tester into the

solution up to the maxi-

mum immersion level,

without touching the bot-

tom of the beaker.

• Stir gently and wait for the reading to

stabilize. TDS1 automatically compensates

for temperature variations.

CALIBRATION

• Immerse the tester into the

HI 70080 (800 ppm) cali-

bration solution, without ex-

ceeding the maximum im-

mersion level.

• Allow the reading to stabi-

lize and using the supplied

screwdriver adjust the cali-

bration trimmer until the

nominal value of the solu-

tion is displayed.

• Calibration is now complete.

BATTERY REPLACEMENT

When the TDS1 can not be switched on or

the display fades, batteries have to be re-

placed.

Pull out the batteries com-

partment as shown in the

drawing, and replace all four

1.5V batteries, while pay-

ing attention to the correct

polarity.

Batteries should only be replaced in a non

hazardous area and using the battery type

specified in this instruction manual.

Recommendations for users

Before using these products, make sure that they are

entirely suitable for the environment in which they are

used. Operation of these instruments in residential areas

could cause interference to radio and TV equipment. Any

variation introduced by the user to the supplied equipment

may degrade the instrument's EMC performance. To avoid

electrical shock, do not use this instrument when voltages

at the measurement surface exceed 24 Vac or 60 Vdc.

To avoid damage or burns, do not perform any

measurement in microwave ovens.

WARRANTY

This meter is guaranteed for six months against defects

in workmanship and materials when used for its intended

purpose and maintained according to instructions. This

warranty is limited to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of

prescribed maintenance are not covered. If service is re-

quired, contact the dealer from whom you purchased the

instrument. If under warranty, report the model number,

date of purchase, serial number and the nature of the

failure. If the repair is not covered by the warranty, you

will be notified of the charges incurred. If the instrument

is to be returned to Hanna Instruments, first obtain a

Returned Goods Authorization Number from the Cus-

tomer Service department and then send it with shipment

costs prepaid. When shipping any instrument, make sure

it is properly packaged for complete protection.

Autres manuels Hanna Instruments Instrument de mesure

Hanna Instruments

Hanna Instruments HI96704C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 95715 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 96710C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 83208 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 991003 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93705 Manuel utilisateur

Hanna Instruments

Hanna Instruments edge DO Manuel utilisateur

Hanna Instruments

Hanna Instruments BL 7916 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI709 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI96709C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI774 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI96700C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI97732 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 9811-5 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 726 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 720 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 95715 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI97725 Manuel utilisateur

Hanna Instruments

Hanna Instruments Edge HI 2020 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 702 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 98129 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI5321 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93709 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 4321 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur