Hakko Electronics FT-8004 Manuel utilisateur

THERMAL WIRE STRIPPER

FT-8004

(with holder part)

●PACKING LIST AND PART NAMES

Please make sure that all items listed below are included in the package.

Thank you for purchasing HAKKO products.

When using the product, please read this manual

and follow the instruction to change the parts.

2019.5

MA03051XZ190508

HAKKO FT-8004 ...................................1

Holder part (for HAKKO FT-8004) .........1

SEMS screw P2 (M3×6) ........................2

Hexagon wrench (1.27mm) ...................1

Instruction Manual ................................1

Hexagon socket set screw (M2.5×2.5)

........2

PACKING LIST

Precautions Regarding Electrostatic Protection

CAUTION

This product includes features such as electrically conductive plastic parts and

grounding of the handle and station as measures to protect the device to be

soldered from the effects of static electricity.

Be sure to observe the following instructions:

⿟The handle and other plastic parts are not insulators, they are conductors. When

replacing parts or repairing, take sufcient care not to expose live electrical parts or

damage insulation materials.

⿟Be sure to ground the unit during use.

Handle

HAKKO FT-8004

Blade (not included)

Hexagon wrench

Hexagon socket set screw (×2)

Instruction Manual

Lead adjuster

THERMAL WIRE STRIPPER

FT-802

SEMS screw P2 (×2)

Holder part

(for HAKKO FT-8004)

OVERSEAS AFFILIATES

U.S.A.: AMERICAN HAKKO PRODUCTS, INC.

TEL: (661) 294-0090 FAX: (661) 294-0096

Toll Free (800)88-HAKKO

4 2 5 5 6

http://www.hakkousa.com

HONG KONG: HAKKO DEVELOPMENT CO., LTD.

TEL: 2811-5588 FAX: 2590-0217

http://www.hakko.com.cn

E-mail:[email protected]

SINGAPORE: HAKKO PRODUCTS PTE., LTD.

TEL: 6748-2277 FAX: 6744-0033

http://www.hakko.com.sg

E-mail:[email protected]

Please access to the following address for the other Sales affiliates.

http://www.hakko.com

HEAD OFFICE

4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN

TEL:+81-6-6561-3225 FAX:+81-6-6561-8466

http://www.hakko.com E-mail:[email protected]

Company and product names are trademarks or registered

trademarks of their respective companies.

WARNING

If output setting is over 70%, the handpiece and holder can be very hot. Please be

sure to turn on the auto-sleep function before use.

(On HAKKO FT-801, please be sure to connect the station and holder with included

connecting cable in order for auto-sleep to function properly.)

WARNING

Operating above 80% output setting can cause stress to the heating element and

shorten the life of the blades. Use 80% and above power only when necessary.

When not using the handle, be sure to place it in the holder.

CAUTION

Since the blades will become hot, place the handle on the handle holder when it is

not being used.

●How to attach the holder part (for HAKKO FT-8004)

Remove the holder part of the

handpiece holder inclusive with

HAKKO FT-801.

Attach the holder part inclusive

with HAKKO FT-8004.

●Removing the blades

Loosen and remove the hexagon socket set screw  xing the blades.

As illustrated below, pull the blade straight out.

●Attaching the lead adjuster

Handle

Attaching the lead adjuster

1 Remove the insulating cover from

the tip on the handle cover L-side

(the side with the HAKKO logo and

HAKKO FT-8004) and remove the

screw from the handle cover L-side.

2 Remove the handle cover L.

3 Align the lead adjuster mounting hole

with the handle cover L mounting

hole, replace the screw, and tighten

it lightly.

4 Firmly  t the nail of the root side of

the insulation cover in the handle

cover.

5 Attach the handle cover L to the

handle. Adjust the length of the lead

adjuster and  rmly tighten the screw.

NOTE:

Pay attention to the direction of the

blades when attaching the lead adjuster.

(See the following  gure.)

Attach the lead adjuster so that the

adjuster plate end is in parallel with the

blade surface.

The lead adjuster can be removed with

the handle cover attached to the handle.

Holder part Holder part

(for HAKKO FT-8004)

Lead adjuster

Handle cover L

Insulating cover

CAUTION

Please be sure to use the included holder part.

CAUTION

⿟When pulling out or inserting blades, be sure that the power is switched off.

⿟Before pulling out the blades, check that the blades have cooled down suf ciently.

Hexagon wrench

Hexagon socket set screw

(M2.5×2.5)

V groove

●Attaching the blades

Blades

Attaching blades

1 Stop provisionally in the tapped hole of

the handle, and do a set the hexagon

socket set screw.

2 Insert the blade so that the blade mounting

ﬂ ange locks into the HAKKO FT-8004. Merge

type V and the V-groove of the back of the

blade.

NOTE:

Blades are not heated unless both blades are

inserted fully. Be sure to use the blades as a set.

3 Fix it with a  nger so that the point of a sword

does not work, tighten the hexagon socket

set screw with the hexagonal wrench to

secure the blades.

Autres manuels Hakko Electronics Outils électriques

Hakko Electronics

Hakko Electronics FM-2023 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-400 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-410 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-601 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR400-53 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-2029 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-301 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-410 Manuel utilisateur

Hakko Electronics

Hakko Electronics FV-310 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-9703 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-950 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-204 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-204 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-2031 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-2030 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-4102 Manuel utilisateur

Hakko Electronics

Hakko Electronics FU-601 Manuel utilisateur

Hakko Electronics

Hakko Electronics FR-4103 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-9707 Manuel utilisateur

Hakko Electronics

Hakko Electronics 933 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-8003 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM-2030 Manuel utilisateur

Hakko Electronics

Hakko Electronics FM2022-05 Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-888D Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel