Haier HWM80-68B Manuel utilisateur
Full automatic washing machine
User's manual
This manual is for
HWM80-68B
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Safety precautions
Contents
Answers to question
Trouble shooting
Packing list Specification
Installation and adjustment
Usage of the drain hose
Preparation before washing
Put in the laundries
Add the detergent and softener
Use the operation knobs and buttons
Installation the water inlet hose
Disposal after washing
*
Finish washing
Close the top lid
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Warning sign
Names of the parts
Meaning and description of the symbols
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Adjustable foot
Front control
board
Front fixed
foot
Rear fixed foot
back cover
Cabinet
Drain hose
Back faceplate
Control panel
film
Control panel
Lint filter(Installed by user)
Filter cover
Level meter
Power line
Pulsator
Inner tub
Detergent box Drier outlet
cover
Top lid B
Cabinet handle
Globe cover
Cool water valve
Top lidA
Adjustable foot
seam
hanging hole
for the drain
hose
Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.
If the power cord is bad, to avoid risk it is required to replace it by the
technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
Do not use water hotter than 65 C .
In case the washing machine is in-
stalled on ground with carpet, do not
block the ventilation hole with carpet.
The ventilation holes
at the bottom
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Earth
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Petrol
Thinner
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
Toprevent the lintin the tubfrom blocking
the cascade outlet and influencing the
cascade effect, please keep the lint filter
in good condition, and install it to proper
position during washing.If the lint filter is
lost or damaged,please contact thelocal
after-sale service department of our
company.
Install the bottom plate
Adjust the installation position
Soft items
Bottom plate Screw
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Back
Front
After openingthe package, pleaselean the
washing machine gently down on soft items
(like towel cloth, blanket, etc.). Install the
bottom plate to the bottom of the machine
with eight screws by a cross screwdriver,
then lift the machine up gently. See to the
figure:
Loosen Fasten
High Low
Adjustable nut
Adjustable leg
The largest allowable slope of the shank base of the machine is 2 .
The slanting or rough ground will result in unstable running or
stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal:
Adjust the adjustable leg:
If the bulb of the level meter at the balance display
position is inside the standard circle, it indicates that
the machine is horizontal. Otherwise you need to
adjust the adjustable leg of the machine.
1.To twist the adjustable leg, please first lift up the
leg side slightly, loosen the adjustable nut, and
then twist the leg.
2.After adjustment, fasten the nut.
Air bubble
Standard circle
Suitable Not suitable
Inner tub Lint filter
After openingthe package, pleasetake out thelint
filter from the document bag,install it tothe filter cover
of inner tub.See to thefigure.
How to change the direction of the drain hose
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Usage of the drain hose
The drain hose shall drain smoothly
1.Dismount the back cover of the washing machine.
2.Lay down the washing machine gently with the front
side facing the ground. Use cross screwdriver to
loosen the eight screws. Take off the bottomplate.
4.Dismount the protecting cover of the drain outlet at the
other side as indicated in Figure 3.
5.Extend the drain hose out of the other side. Fix the drain
hose onto the cabinet with the drain hose rack. Set the
drain hose nut on, and fasten the nut to the direction
indicated in the figure, as per Figure 4.
6.Install the protecting cover of the drain outlet to the other
side, as indicated in Figure 5.
7.Install the bottom plate (method the same as stated
above). Lift up the washing
machine gently.
3.Put down the outer drain hose. Twist the drain hose nut
counterclockwise to take it off as indicated in Figure 1.
Take off the drain hose rack. Put the drain hose into
the cabinet as indicated in Figure 2.
back
front
bottom plate
drain outlet
protecting
cover fasten
drain hose nut
Drain hose nut Drain hose rack
Outer
drain hose
Loosen
soft item
Figure 1
Figure 3 Figure 4
Figure 5
Figure 2
If the extra hose is too long, cut it either
at point A or B.
Install the lint filter
Install the water inlet pipe
Connection between the water inlet hose jointer and the water faucet
Water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.
2. Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four
screws and take out the bush inside the jointer. See to Figure 3.
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3. Fasten thefour screws ofthe water inlethose jointer evenly. See toFigure 4.
About 4mm after twisting
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
About above 2mm after twisting
Water inlet hose jointer
Screw knife
Screw
Bushing
Nameplate
Screw nut
Water inlet hose Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
Figure 6
Slider
Lock level
Install the water inlet hose
4. Take off the nameplate.Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Connection between the water inlet hose and the washing machine
1 Do not takeoff the waterabsorption cushion. Pleasecheck
if the cushion isdropped or damaged eachtime before using.
If it happens so,please duly contact ourafter-sale service
department.
2 Set the nutof the water inlethose on the waterinlet valve jointer.
3 Fasten the nut.Swing it gently toconfirm if it's fastenedwell.
Water absorption cushion.
Water inlet
hose nut
Water inlet valvejointer
7
Dismount the water inlet hose
Connection between the water inlet hose jointer and the water inlet hose
Check the connection between the water inlet hose jointer and the
water faucet
1.Swing the hosegently to checkif it is fastened stably.
2.After installation, open thefaucet to check ifit leaks water.
3.Do not bend thehose by force.
4.Each time before using,please check if theconnection
between the water inlethose jointer and thewater faucet,
and the installation ofthe water inlet hoseisfirm, so as
to avoid dropping owingto improper installation.
1. Push downthe slider.Plug the waterinlet hose intothe jointer.
2. Hang thelock lever ontothe jointer.Release
the slider tilla click soundis heard.
Lock level
Slider
The water inlet
hose jointer
Slider
Locking level
1. Close thewater faucet.
2 .Press thelock lever andpush down theslider. Thenpull off the
water inlet hose.If the machineis used more than once every
week, the waterinlet hose jointercan remain onthe faucet to
avoid damaging thefastening screws.
1 Preparation before washing
Preparation before washing
1.Connect the water inlet hose. Open
the water faucet.
2.Confirm that the washing machine is
earthed reliably. Then insert the
power plug into the receptacle. The
earth terminal shall not link to gas
pipeline and faucet water pipeline.
3.Put down the drain hose.
Pay attention to followings before washing the laundries
Check if
the laundries
has special
requirement
on washing
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Haier Rondelle
Haier
Haier HWM120-AS Manuel utilisateur
Haier
Haier 50FREE-3B Manuel utilisateur
Haier
Haier HWD1600 Manuel utilisateur
Haier
Haier XPB82-187 Series Manuel utilisateur
Haier
Haier HWM150-0523S Manuel utilisateur
Haier
Haier HWM25-0623S Manuel utilisateur
Haier
Haier AWT-120LI Manuel utilisateur
Haier
Haier HW110-B14979S8EU1 Manuel utilisateur
Haier
Haier HW80-BD1626 Manuel utilisateur
Haier
Haier Twin-tub Washing Manuel utilisateur
Haier
Haier XPB90-99VGS Manuel utilisateur
Haier
Haier HW80-B14979 Manuel utilisateur
Haier
Haier HWM130-0523S Manuel utilisateur
Haier
Haier HW70-I1286 Manuel utilisateur
Haier
Haier HA800TX Guide de l'utilisateur
Haier
Haier HW70-IM12929 Manuel utilisateur
Haier
Haier WD-8888-71 Manuel utilisateur
Haier
Haier HWM 80-200 S Manuel utilisateur
Haier
Haier HWM70-23S Manuel utilisateur
Haier
Haier HWM100-113S Manuel utilisateur
