Hach Orbisphere 51 Series Manuel rapide
DOC024.98.93134
ORBISPHERE Model 51x
Analyzer with K-M1100 and TC
Sensors
11/2017, Edition 2
Basic User Manual
Allgemeines Benutzerhandbuch
Manuel d'utilisation de base
Manual básico del usuario
Základní uživatelská příručka
Alapvető felhasználói kézikönyv
Основно ръководство за потребителя
English..............................................................................................................................3
Deutsch.......................................................................................................................... 29
Français......................................................................................................................... 58
Español.......................................................................................................................... 87
Čeština......................................................................................................................... 115
Magyar......................................................................................................................... 143
български................................................................................................................... 171
2
Specifications
Specifications are subject to change without notice.
Analyzer
Specification Details
Operating temperature –5 to 50°C (23 to 122 °F)
Storage temperature –20 to 70°C (–4 to 158 °F)
Operating humidity 0 to 95% non condensing relative humidity
Operating altitude From 0 to 2,000 m. (6,550 ft.) above sea level
EMC requirements EN61326-1: EMC Directive
Note: The wall mount instrument is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take adequate
measures.
Korean registration
User Guidance for EMC Class A Equipment
업무용을 위한 EMC 등급 A 장치에 대한
사용자 지침
사용자안내문
A 급 기기 ( 업무용 방송통신기자재 )
이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의
하시기 바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합니다.
CE compliance EN61010-1: LVD Directive
Safety rating ETL, conforming to UL 61010-1 and CSA 22.2 No. 61010-1
Enclosure ratings IP 65; Totally protected against dust; Protected against low pressure jets of water
from all directions.
NEMA 4X (wall mount only); Totally protected against dust; Protected against
pressure jets of water from all directions.
WARNING
Enclosure rating does not apply to external power supply for benchtop
instruments.
Power supply Universal 100 VAC to 240 VAC @ 50/60 Hz - 40VA; 10 to 30 VDC - 30W
Analog current output version
on the measurement
board(s)
4-20 mA (default) or 0-20 mA (configuration with software);
3 configurable outputs: Maximum load: 500 ohm; Sensitivity: 20μA;
Accuracy: ± 0.5% (between operating temperature limits)
Analog voltage output
version on the measurement
board(s)
0- 5 V output (hardware option);
3 configurable outputs; Minimum load: 10 KOhm; Sensitivity: 5 mV;
Accuracy: ± 0.5% (between operating temperature limits)
Measurement alarm relays
on the measurement
board(s)
Three alarm relays per measurement board; 1A-30 VAC or 0.5A-50 VDC on a
resistance load.
Configurable to Normally Open [NO] or Normally Closed [NC] contacts by
changing the jumper positions.
WARNING
Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC
RMS
English 3
Specification Details
System alarm relay on the
main board
One system alarm relay; 1A-30 VAC or 0.5A-50 VDC on a resistance load.
Normally closed [NC] (NO relay also available) when instrument is turned on.
WARNING
Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC
RMS
Thermal cut off Prevents ageing of sensors when exposed to high temperatures
Options USB host; Ethernet 10/100 Base-T
Wall and pipe mount
instrument
(H x D x W)
236.5 x 160 x 250 mm; Weight 4.25 kg
9.31 x 6.30 x 9.84 in.; Weight 8.82 lbs
Panel mount instrument
(housing) (H x D x W)
156 (123) x 250 x 220 (214) mm; Weight 3.35 kg
6.14 (4.84) x 9.84 x 8.86 (8.43) in.; Weight 6.62 lbs
K-M1100 sensor
Specification Details
Sample temperature Measurement from –5 to 50°C (23 to 122°F)
Sensor resistant to temperature from –5 to 100°C (23 to 212°F)
Sample pressure 1 to 20 bar absolute (14.5 to 290 psia)
Sample flow rate
requirement
50 to 300 mL/min
Sample types K1100 sensor: Water only
M1100 sensor (low range): Water and beer
M1100 sensor (high range): Water, beer, wine, wort and carbonated drinks
For oxygen measurement
in
liquid phase gas phase
Measurement range Low range sensors 0 to 2000 ppb (dissolved.
Indicative values until
5000 ppb)
0 to 50 mbar or 0 to 5% O2 (at
atm pressure)
High range sensors 0 to 40 ppm (dissolved) 0 to 1 bar or 0 to 100% O2 (at
atm pressure)
Repeatability Low range sensors ± 0.4 ppb or 1%,
whichever is the greater
± 0.01 mbar or 10 ppm gas or
1%, whichever is the greater
High range sensors ± 0.015 ppm or ± 2%,
whichever is the greater
± 0.4 mbar or 400 ppm gas or
2%, whichever is the greater
Reproducibility Low range sensors ± 0.8 ppb or 2%,
whichever is the greater
± 0.02 mbar or 20 ppm gas or
2%, whichever is the greater
High range sensors ± 0.02 ppm or ± 3%,
whichever is the greater
± 0.5 mbar or 500 ppm gas or
3%, whichever is the greater
Accuracy Low range sensors ± 0.8 ppb or 2%,
whichever is the greater
± 0.02 mbar or 20 ppm gas (at
atm pressure) or 2% of
reading, whichever is the
greater
High range sensors ± 0.02 ppm or ± 3%,
whichever is the greater
± 0.5 mbar or 500 ppm gas (at
atm pressure) or 3% of
reading, whichever is the
greater
4 English
Specification Details
Limit of detection
(LOD)
Low range sensors 0.6 ppb 0.015 mbar or 15 ppm gas (at
atm pressure)
High range sensors 0.015 ppm 0.4 mbar or 400 ppm gas (at
atm pressure)
Response time
(90%)
Low range sensors < 30 seconds < 10 seconds
High range sensors < 50 seconds < 10 seconds
Display resolution High and low range sensors 0.1 ppb 0.001 mbar or 1 ppm gas
Calibration Low range sensors: Single point calibration (zero)
High range sensors: Two at cap replacement (zero and air), one during use (air)
Calibration sample Low range sensors: Standard 99.999% N2 (quality 50) or equivalent oxygen free gas
High range sensors: Standard 99.999% N2 (quality 30) or equivalent oxygen free gas, air
M1100 12 mm (PG
13.5) sensor (L x W)
246 x 47 mm - weight 0.6 kg
9.69 x 1.85 in. - weight 1.32 lbs
K1100 and
M1100 28 mm
sensor (L x W)
143.50 x 49 mm - weight 0.74 kg
5.65 x 1.93 in. - weight 1.63 lbs
Calibration device Weight 0.7 kg
TC sensor
Sensor type
31 250 H2, 31260 H2 and 31290 (purge gas N2)
For other purge gases, please contact your Hach
representative for specification.
31 550 N2, 31560 N2
and 31590 (purge
gas CO2)
Specification Membrane 29561A Membrane 2952A Membrane 2935A Membrane 29561A
Thickness [μm] 25 25 25 25
Material PFA ETFE ECTFE (Halar) PFA
Recommended
applications
Waste gas offgas,
reactor coolant Reactor coolant High H2 level In-line beverage
Radiation limits 105 rad 108 rad 108 rad 105
Measurement range
at 25°C
0-2 ppm, or
0-25 cc/kg, or
0-1.5 bar
0-10 ppm, or
0-120 cc/kg, or
0-6 bar
0-20 ppm, or
0-220 cc/kg, or
0-12 bar
0-350 ppm, or
0-300 mL/L, or
0-20 bar
Accuracy (sample
temperature 20-50°C
within ± 5°C of
calibration
temperature)
The greater of ±1%
of reading or ±
2 ppb, or ±
0.03cc/kg, or ±
1.5 mbar
The greater of ±1%
of reading or ±
8 ppb, or ± 0.1cc/kg,
or ± 6 mbar
The greater of ±1%
of reading or ±
25 ppb, or ±
0.4 cc/kg, or ±
20 mbar
The greater of ±2%
of reading or ±
0.3 ppm, or ±
0.25mL/L, or ±
15 mbar
Accuracy (sample
temperature 0-50°C
independent of
calibration
temperature)
The greater of ±3%
of reading or ±
15 ppb or ±
0.18 cc/kg or ±
6 mbar
The greater of ±3%
of reading or ±
60 ppb or ±
0.6 cc/kg, or ±
20 mbar
The greater of ±3%
of reading or ±
150 ppb or ±
2.5 cc/kg, or ±
50 mbar
The greater of ±4%
of reading or ±
1 ppm or ± 0.8 mL/L
or ± 34 mbar
Measurement cycle
(seconds) 17 22
English 5
Sensor type
31 250 H2, 31260 H2 and 31290 (purge gas N2)
For other purge gases, please contact your Hach
representative for specification.
31 550 N2, 31560 N2
and 31590 (purge
gas CO2)
Specification Membrane 29561A Membrane 2952A Membrane 2935A Membrane 29561A
Sample flow rate1
(through flow
chamber)
220 mL/min 200 mL/min 100 mL/min 300 mL/min
Linear flow rate2
(past sensor socket) N/A N/A N/A 150 cm/sec
Purge gas pressure regulator
Specification Details
Model 29089S4 (0.25 in.), 29089S6 (6 mm)
Filtration grade 40 μm
Input pressure min/max 1 bar / 16 bar
Output pressure min/max 0.5 bar / 7 bar
Standard nominal flow rate 900 Liters/minute
Condensate volume 22 cm3
Temperature range (ambient and media) -10°C to 60°C
Purge gas dew point -10°C (+14°F)
Construction materials Housing: metal; Condensate bowl: polycarbonate; Bowl guard: metal
Weight 460 g.
Dimension in cm (overall) 21 x 11.5 x 8
Expanded manual version
For additional information, refer to the expanded version of this manual, which is available on the
manufacturer's website.
General information
In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential
damages resulting from any defect or omission in this manual. The manufacturer reserves the right to
make changes in this manual and the products it describes at any time, without notice or obligation.
Revised editions are found on the manufacturer’s website.
Safety information
N O T I C E
The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,
without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent
permitted under applicable law. The user is solely responsible to identify critical application risks and install
appropriate mechanisms to protect processes during a possible equipment malfunction.
1Minimal flow through an ORBISPHERE 32001 flow chamber
2Minimal flow past an ORBISPHERE 29501 sensor socket
6 English
Please read this entire manual before unpacking, setting up or operating this equipment. Pay
attention to all danger and caution statements. Failure to do so could result in serious injury to the
operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or install this
equipment in any manner other than that specified in this manual.
Use of hazard information
D A N G E R
Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
Indicates a potentially hazardous situation that may result in minor or moderate injury.
N O T I C E
Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special
emphasis.
Precautionary labels
Read all labels and tags attached to the instrument. Personal injury or damage to the instrument
could occur if not observed. A symbol on the instrument is referenced in the manual with a
precautionary statement.
This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential
injury. If on the instrument, refer to the instruction manual for operation or safety information.
This symbol indicates that a risk of electrical shock and/or electrocution exists.
This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and
indicates that care must be taken to prevent damage with the equipment.
This symbol, when noted on a product, indicates the instrument is connected to alternate current.
Electrical equipment marked with this symbol may not be disposed of in European domestic or
public disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no
charge to the user.
Products marked with this symbol indicates that the product contains toxic or hazardous substances
or elements. The number inside the symbol indicates the environmental protection use period in
years.
Operating altitude
This instrument is rated for an altitude of 2000 m (6562 ft) maximum. Use of this instrument at an
altitude higher than 2000 m can slightly increase the potential for the electrical insulation to break
down, which can result in an electric shock hazard. The manufacturer recommends that users with
concerns contact technical support.
English 7
Installation
This section provides necessary information to install and connect the analyzer. The installation of
the analyzer should be performed in accordance with relevant local regulations.
D A N G E R
Electrocution hazard. Do not connect AC power directly to a DC powered instrument.
D A N G E R
Electrocution hazard. Always remove power to the instrument before making electrical connections.
D A N G E R
Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault
Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power
source.
WARNING
Potential Electrocution Hazard. A protective earth (PE) ground connection is required for both
100-240 VAC and 5 VDC wiring applications. Failure to connect a good PE ground connection can
result in shock hazards and poor performance due to electromagnetic interferences. ALWAYS connect
a good PE ground to the controller terminal.
CAUTION
Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the
document.
N O T I C E
Install the device in a location and position that gives easy access to the disconnect device and its operation.
N O T I C E
Potential Instrument Damage. Delicate internal electronic components can be damaged by static electricity,
resulting in degraded performance or eventual failure.
Wall mounting
1. Attach the U-bracket (provided) to the wall with two screws (not
provided).
2. Tilt the instrument slightly backwards to align the bracket pins and
the insertion slots, and slide the instrument onto the bracket as
shown.
3. Insert the 2 locking screws with washers through the side slots.
4. Adjust the instrument angle for better screen vision, and lock both
side screws.
8 English
Pipe mounting
1. Assemble the pipe mount bracket to the U-bracket, using the two screws provided.
2. Attach this assembly to the pipe using two clamps (not provided).
3. Slide the instrument onto the bracket.
4. Insert the 2 locking screws with washers through the side slots.
5. Adjust the instrument angle for better screen vision, and lock both side screws.
Panel mounting
WARNING
Electrocution hazard. If the cable and connector for the power supply are not accessible after
installation, an accessible local disconnection means for the instrument power is mandatory.
1-3 4-5 6-7
1. Cut an opening in the panel to accommodate the bracket frame provided.
2. Install the provided frame in the opening.
3. Fold the 6 tabs over the panel lips, using adjustable joint pliers.
4. Slide the instrument in the bracket frame. The instrument should go over the four "T" pins. Rotate the 4 fast
locking screws on both sides of the front panel and slide it in.
5. Rotate the 4 fast locking screws 1/4 turn twice in the lock direction as indicated on the side of the front panel.
This locks the instrument in place on the four "T" pins.
6. To access the connections inside the instrument, remove the instrument housing (six screws on the back
panel, and slide the housing back out)
7. Pass the cables through the housing, then through the cable gland (if applicable) and then perform the
connections as detailed below.
English 9
Instrument connections
Figure 1 Connections - panel (left); wall/pipe (right)
1 Power cable 6 K-M1100 Sensor connection
2 Ethernet cable gland 7 External pressure sensor connection
3 USB-A host connector 8 Input/Output 2 cable gland
4 USB-B 4-pin connector 9 TC Sensor connection
5 Input/Output 1 cable gland 10 Keylock (wall/pipe mount only)
Connection to mains power supply
Power supply connection (low voltage instruments)
For low voltage instruments (10-30 VDC), connection to the mains power supply is with a 8-pin
BINDER connector (supplied).
Note: The connectors are grooved to avoid an incorrect fitting to the instrument.
Connect the power cable to the connector as follows:
Figure 2 BINDER connector Pin Connections:
1. Power 10-30 VDC
2. Ground
3. Ground
4. Ground
5. Not used
6. Power 10-30 VDC
7. Power 10-30 VDC
8. Earth
Figure 3 Wiring side view
Power supply connection (high voltage instruments)
D A N G E R
Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the
document.
10 English
Autres manuels pour Orbisphere 51 Series
1
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Hach Instrument de mesure
Hach
Hach LXV321.99.00001 Manuel utilisateur
Hach
Hach DR 6000 Manuel utilisateur
Hach
Hach DR2400 Manuel utilisateur
Hach
Hach sensION+ EC71 Manuel utilisateur
Hach
Hach LANGE LOC 100 Manuel utilisateur
Hach
Hach ORBISPHERE G1100 Manuel utilisateur
Hach
Hach Polymetron 9586 Manuel utilisateur
Hach
Hach AMTAX sc Manuel utilisateur
Hach
Hach HQ440d Manuel rapide
Hach
Hach DOC026.52.00769 Manuel utilisateur
Hach
Hach LDO10101 Manuel utilisateur
Hach
Hach REFO 3 Manuel utilisateur
Hach
Hach 2100Q Manuel rapide
Hach
Hach 1735 TRO Manuel utilisateur
Hach
Hach Hach SL1000 Manuel rapide
Hach
Hach 50 14 T Probe Manuel utilisateur
Hach
Hach POCKET COLORIMETER II Manuel utilisateur
Hach
Hach sensION3 Manuel utilisateur
Hach
Hach Lange CL17 Manuel utilisateur
Hach
Hach TL2310 Manuel rapide
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur