Hach 9523sc Manuel utilisateur

DOC023.97.80570

9525sc DCCP System

09/2020, Edition 7

User Manual

Bedienungsanleitung

Manuale utente

Manuel de l'utilisateur

Manual del usuario

Brugervejledning

Kullanıcı Kılavuzu

Εγχειρίδιο χρήσης

Návod na použitie

Table of Contents

English..............................................................................................................................3

Deutsch.......................................................................................................................... 30

Italiano............................................................................................................................ 58

Français......................................................................................................................... 86

Español........................................................................................................................ 114

Dansk............................................................................................................................142

Türkçe...........................................................................................................................169

Ελληνικά...................................................................................................................... 196

Slovenský jazyk......................................................................................................... 224

Table of Contents

1 Specifications on page 3

2 General information on page 4

3 Installation on page 10

4 Startup on page 17

5 User interface and navigation on page 18

6 Operation on page 20

7 Advanced operation on page 21

8 Maintenance on page 22

9 Troubleshooting on page 28

10 Replacement parts and accessories

on page 29

Section 1 Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions 91 x 62 x 38 cm (36 x 24.5 x 15 inches)

Weight Degas-only DCCP system : 27.7 kg (61 lb)

DCCP system: 50 kg (110 lb)

Power requirements US: 110 to 120 VAC, 1 phase, 50/60 Hz

EU: 220 to 240 VAC, 1 phase, 50/60 Hz

Main supply voltage fluctuation ±10% of nominal voltage

Power consumption 1.6 kVA

Pollution degree 2

Installation category II

Altitude 2000 m (6562 ft) maximum

Operating temperature Without regenerative cooling option: 2 to 50 °C (36 to 122 °F), 0 to

85% relative humidity, non-condensing

With regenerative cooling option: 2 to 45 °C (36 to 113 °F), 0 to

85% relative humidity, non-condensing

Operating temperature

(recommended)

23 to 27 °C (73 to 81 °F)

Storage temperature 0 to 50 °C (32 to 122 °F)

8315 Conductivity sensor Cell constant, k: 0.01 cm-1

Measurement range: 0.01 to 200 μS/cm

Sensor accuracy: less than ± 2%

Power to the sensor(s) is supplied by the controller.

Controller power requirements 100 to 240 VAC ±10%, 50/60 Hz

Controller and instrument

rating

IP66/NEMA 4X

Sample water Flow rate: 100 to 150 mL/min; 6 to 9 L/hr (1.5 to 2.4 gal/hr)

Temperature: 25 °C ± 1 °C (77 °F ± 2 °F) recommended; 2 to

54 °C (36 to 129 °F) without regenerative cooling option or 2 to

45 °C (36 to 113 °F) with regenerative cooling option

Pressure: 6.9 bar (100 psig)

English 3

Specification Details

Cooling water Note: Cooling water is not used if the instrument has the regenerative cooling option.

Flow rate: 0.8 L/min (0.2 gal/min)

Temperature: 22 °C (71.6 °F)

Use clean water with no suspended solids and a low hardness.

Use water that is low in chlorides. Chlorides can cause corrosion

in the stainless steel coil and shell.

Sample water connections ¼-inch tube fittings

Cooling water connections ¼-inch tube fittings

Flow cell ¾-inch FNPT, 316 stainless steel

Certifications CE, UL, CSA

Section 2 General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

2.1 Safety information

The manufacturer is not responsible for any damages due to misapplication or misuse of this product

including, without limitation, direct, incidental and consequential damages, and disclaims such

damages to the full extent permitted under applicable law. The user is soley responsible to identify

critical application risks and install appropriate mechanisms to protect processes during a possible

equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

2.1.1 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that

requires special emphasis.

4 English

2.1.2 Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

Electrical equipment marked with this symbol may not be disposed of in European

domestic or public disposal systems. Return old or end-of-life equipment to the

manufacturer for disposal at no charge to the user.

This symbol, if noted on the instrument, references the instruction manual for operation

and/or safety information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the need for protective eye wear.

This symbol indicates that the marked item can be hot and should not be touched without

care.

This symbol, when noted on the product, identifies the location of a fuse or current

limiting device.

2.1.3 Compliance and certification

CAUTION

This equipment is not intended for use in residential environments and may not provide adequate

protection to radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, ICES-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

English 5

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

2.2 Intended use

The 9525sc DCCP System is intended for use by individuals who measure water quality parameters

in a sample stream of high purity water. The 9525sc DCCP System does not treat or alter water.

6 English

2.3 Product overview

The 9525sc degas-only DCCP (degas cation conductivity panel) system removes CO2 and measures

degassed cation conductivity (DCC). The system measures a sample stream of high purity water.

The system has one sensor and one controller. Refer to Figure 1.

Figure 1 9525sc degas-only DCCP system

1 Heater 7 Power indicator light1

2 Sample cooler 8 Temperature controller

3 Polymetron 8315 conductivity sensor 9 Sample flow meter

4 SC200 Controller (or Polymetron

9500 controller)

10 Sample flow valve

5 Electrical enclosure 11 Flow cell

6 Power switch

1The power indicator light starts and stops with the heater.

English 7

The 9525sc DCCP system removes CO2 and measures specific conductivity (SC), cation

conductivity (CC) and degassed cation conductivity (DCC) and calculates pH. The system measures

a sample stream of high purity water. The system has three conductivity sensors and two controllers.

The top controller is connected to two sensors and shows the SC (channel 1) and CC (channel 2)

measurements. The bottom controller shows the DCC measurement. Refer to Figure 2.

Figure 2 9525sc DCCP system

1 Heater 7 Power switch

2 Sample cooler 8 Power indicator light2

3 SC200 Controller (or Polymetron

9500 controller)

9 Temperature controller

4 Polymetron 8315 conductivity sensor (3x) 10 Sample flow meter

5 Electrical enclosure 11 Sample flow valve

6 Flow cell (3x) 12 Resin column

2The power indicator light starts and stops with the heater.

8 English

2.4 Product components

Make sure that all components have been received. Refer to Figure 3. If any items are missing or

damaged, contact the manufacturer or a sales representative immediately.

Figure 3 Product components

1 9525sc DCCP system (or 9525sc degas-only

DCCP system)

4 Tubing clamp for condensate drain

2 Manuals for Polymetron 8315 sensor,

controller and 9525sc DCCP

5 Ferrite for 220–240 V main power

3 Condensate drain tubing, 3/8-inch ID x

2.44 m (8 ft)

English 9

2.5 Customer-supplied parts

Before installation, collect the components that follow. Refer to Figure 4.

Figure 4 Customer-supplied parts

1 Sample plumbing parts 6 Tubing, ¼-inch OD3

2 Shutoff valve 7 Electrical parts

3 Tubing, ¼-inch OD 8 110/120 VAC: Wire conductors, 3.31 mm2

(12 AWG)

4 Cooling water plumbing parts39 220/240 VAC: Wire conductors, 2.08 mm2

(14 AWG)

5 Shutoff valves (2x)310 Conduit fitting for main power

Section 3 Installation

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this

section of the document.

3.1 Installation guidelines

Install the instrument:

• In a clean, dry, well-ventilated and temperature-controlled location. Refer to the operating

temperature and humidity specifications in Specifications on page 3.

• In a location with no mechanical vibrations and electronic noise.

• As close to the sample source as possible to decrease analysis delay.

• Near an open drain.

• Away from direct sunlight and heat sources.

• So that the power switch is visible and easily accessible.

• In a location where there is sufficient clearance around it to make plumbing and electrical

connections. Refer to Figure 5 on page 12.

3Not applicable to instruments with the regenerative cooling option.

10 English

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Hach Instrument de mesure

Hach

Hach PHC725 Manuel utilisateur

Hach

Hach LDO10101 Manuel utilisateur

Hach

Hach pHD Sensor Manuel utilisateur

Hach

Hach ORBISPHERE 410 Manuel utilisateur

Hach

Hach CLF10sc Manuel utilisateur

Hach

Hach 9186 Manuel utilisateur

Hach

Hach LBOD101 Manuel utilisateur

Hach

Hach Lange DR 3900 Manuel utilisateur

Hach

Hach BioTector B7000 Manuel utilisateur

Hach

Hach sensION3 Guide de référence

Hach

Hach 2100P Guide de référence

Hach

Hach 5500sc Mode d'emploi

Hach

Hach TOC-X5 Manuel utilisateur

Hach

Hach sension6 Manuel utilisateur

Hach

Hach HQ440d Manuel rapide

Hach

Hach PHC705A Manuel utilisateur

Hach

Hach Polymetron 9586 Manuel utilisateur

Hach

Hach sensION+ pH1 Manuel utilisateur

Hach

Hach 500sc SiO2 Mode d’emploi

Hach

Hach H120 Manuel utilisateur

Hach

Hach 8520600 Manuel utilisateur

Hach

Hach MTC101 Manuel utilisateur

Hach

Hach POCKET COLORIMETER II LCK 325 Guide de l'utilisateur

Hach

Hach Hach SL1000 Manuel rapide

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur